Mitsubishi Pajero Models Repair Service Manual 2010-2012

Complete service repair manual with Electrical Wiring Diagrams for Mitsubishi Pajero 2010-2012, with all the technical information to maintain, diagnose, repair, and rebuild like professional mechanics.

Mitsubishi Pajero workshop service repair manual includes:
* Numbered table of contents easy to use so that you can find the information you need fast.
* Detailed sub-steps expand on repair procedure information
* Numbered instructions guide you through every repair procedure step by step.
* Troubleshooting and electrical service procedures are combined with detailed wiring diagrams for ease of use.
* Notes, cautions and warnings throughout each chapter pinpoint critical information.
* Bold figure number help you quickly match illustrations with instructions.
* Detailed illustrations, drawings and photos guide you through every procedure.
* Enlarged inset helps you identify and examine parts in detail.

'10 Mitsubishi Pajero Sport Workshop Service Manual (MUT-III).iso
'10 Mitsubishi Pajero Workshop Service Manual (MUT-III).iso
'11 Mitsubishi Pajero Sport Workshop Service Manual (MUT-III).iso
'11 Mitsubishi Pajero Workshop Service Manual (MUT-III).iso
'12 Mitsubishi Pajero Workshop Service Manual (MUT-III).iso

PRODUCT DETAILS:
Total Pages: 3 GB
File Format: DVD iso disc image
Language: English

TABLE OF CONTENTS
GR00000100-80A....1
  CONFIGURATION DIAGRAMS....1
    OVERALL CONFIGURATION DIAGRAM....2
    HOW TO READ CONFIGURATION DIAGRAMS....3
    ENGINE COMPARTMENT....4
    TRANSMISSION....8
    DASH PANEL....10
    JUNCTION BLOCK AND STEERING COLUMN....16
    FLOOR AND ROOF....18
    DOOR....22
    LIFTGATE....24
GR00000200-80....25
  CONFIGURATION DIAGRAMS....25
GR00000300-00....27
  GENERAL....27
GR00000300-80B....29
  SPLICE LOCATIONS....29
    HOW TO READ SPLICE LOCATIONS....30
    INDEX....31
    ENGINE COMPARTMENT....32
    RELAY BOX....33
    JUNCTION BLOCK....33
    STEERING COLUMN....34
    DASH PANEL....36
    FLOOR AND ROOF....38
    DOOR....40
    LIFTGATE....41
GR00000400-70....43
  COMPONENT LOCATIONS....43
    FUSIBLE LINK, FUSE AND STORAGE CONNECTOR....44
    INSPECTION TERMINAL....45
    GROUNDING....46
    RELAY....48
    SENSOR....50
    GROUNDING CABLE....55
    CONTROL UNIT....56
    SOLENOID AND SOLENOID VALVE....58
    DIODE....59
    OTHER DEVICES....60
GR00000400-90....63
  CIRCUIT DIAGRAMS....63
    HOW TO READ CIRCUIT DIAGRAMS....66
      WIRE COLOR CODES....71
    JUNCTION BLOCK....72
    JOINT CONNECTOR....74
    CENTRALIZED JUNCTION....77
      FUSIBLE LINK AND FUSE....77
    POWER DISTRIBUTION SYSTEM....84
    STARTING SYSTEM....88
    IGNITION SYSTEM....89
    CHARGING SYSTEM....90
    MFI SYSTEM....92
    INVECS-II 4A/T....102
    HEADLIGHT <VEHICLES FOR USA>....112
    HEADLIGHT <VEHICLES FOR CANADA>....114
    TAILLIGHT, POSITION LIGHT AND LICENSE PLATE LIGHT....118
    FOG LIGHT....120
    DOME LIGHT, MAP LIGHT AND CARGO SPACE LIGHT <VEHICLES WITHOUT KEYLESS ENTRY SYSTEM>....122
    DOME LIGHT, MAP LIGHT AND CARGO SPACE LIGHT <VEHICLES WITH KEYLESS ENTRY SYSTEM>....124
    DOOR LIGHT....127
    IGNITION KEY HOLE ILLUMINATION LIGHT....128
    VANITY MIRROR LIGHT....129
    GLOVE BOX LIGHT....130
    TURN-SIGNAL LIGHT AND HAZARD WARNING LIGHT <VEHICLES WITHOUT KEYLESS ENTRY SYSTEM>....132
    TURN-SIGNAL LIGHT AND HAZARD WARNING LIGHT <VEHICLES WITH KEYLESS ENTRY SYSTEM>....134
    STOPLIGHT....136
    BACKUP LIGHT....138
    HORN....139
    METER AND GAUGE....140
    COMPASS AND TEMPERATURE DISPLAY....142
    FUEL WARNING LIGHT, OIL PRESSURE WARNING LIGHT, BRAKE WARNING LIGHT, SEAT BELT WARNING LIGHT....144
    POWER WINDOWS <VEHICLES WITHOUT KEYLESS ENTRY SYSTEM>....146
    POWER WINDOWS <VEHICLES WITH KEYLESS ENTRY SYSTEM>....150
    CENTRAL DOOR LOCKING SYSTEM <VEHICLES WITHOUT KEYLESS ENTRY SYSTEM>....156
    CENTRAL DOOR LOCKING SYSTEM <VEHICLES WITH KEYLESS ENTRY SYSTEM>....160
    HEATER....172
    AIR CONDITIONING SYSTEM....174
    REAR HEATER....180
    WINDSHIELD WIPER AND WASHER....183
    REAR WIPER AND WASHER....184
    REAR WINDOW DEFOGGER AND DOOR MIRROR HEATER....186
    REMOTE CONTROLLED MIRROR....189
    AUTO-DIMMING MIRROR....190
    RADIO, TAPE PLAYER AND CD PLAYER <VEHICLES WITHOUT AMPLIFIER>....192
    RADIO, TAPE PLAYER AND CD PLAYER <VEHICLES WITH AMPLIFIER>....194
    CLOCK....197
    CIGARETTE LIGHTER....198
    ACCESSORY SOCKET....199
    SUNROOF....200
    LIGHTING MONITOR TONE ALARM....204
    KEY REMINDER TONE ALARM....205
    SEAT BELT TONE ALARM....206
    RHEOSTAT....207
    AUTO-CRUISE CONTROL SYSTEM....208
    FULL TIME 4WD SYSTEM....214
    ANTI-LOCK BRAKING SYSTEM (ABS) <RWD>....216
    ANTI-LOCK BRAKING SYSTEM (ABS) <4WD>....220
    SUPPLEMENTAL RESTRAINT SYSTEM (SRS)....224
    HEATED SEAT....226
    THEFT-ALARM SYSTEM....228
    IMMOBILIZER SYSTEM....236
GR00001000-00....239
  GENERAL <BODY AND CHASSIS>....239
    HOW TO USE THIS MANUAL....241
      MAINTENANCE, REPAIR AND SERVICING EXPLANATIONS....241
      DEFINITION OF TERMS....241
      TIGHTENING TORQUE INDICATION....241
      SPECIAL TOOL NOTE....241
      ABBREVIATIONS....241
    TROUBLESHOOTING GUIDELINES....244
      VERIFY THE COMPLAINT....244
      DETERMINE POSSIBLE CAUSES....244
      FIND THE PROBLEM....244
      REPAIR THE PROBLEM....244
      VERIFY THE REPAIR....244
    HOW TO USE TROUBLESHOOTING/INSPECTION SERVICE POINTS....245
      TROUBLESHOOTING CONTENTS....245
      HOW TO USE THE INSPECTION PROCEDURES....247
      CONNECTOR MEASUREMENT SERVICE POINTS....249
      CONNECTOR INSPECTION SERVICE POINTS....251
      HOW TO COPE WITH INTERMITTENT MALFUNCTIONS....252
      INSPECTION SERVICE POINTS FOR A BLOWN FUSE....254
    VEHICLE IDENTIFICATION....255
      VEHICLE IDENTIFICATION....255
        VEHICLE IDENTIFICATION NUMBER LOCATION....255
        VEHICLE IDENTIFICATION CODE CHART PLATE....255
        VEHICLE IDENTIFICATION NUMBER LIST....256
        VEHICLES IDENTIFICATION CODE PLATE....256
        CHASSIS NUMBER....257
        VEHICLE SAFETY CERTIFICATION LABEL....257
        ENGINE MODEL STAMPING....257
        THEFT PROTECTION....258
        LOCATIONS....259
    PRECAUTIONS BEFORE SERVICE....261
      SUPPLEMENTAL RESTRAINT SYSTEM (SRS)....261
      SERVICING ELECTRICAL SYSTEM....261
      VEHICLE WASHING....262
      APPLYING ANTI-CORROSION AGENT OR OTHER UNDERCOAT AGENTS....262
      SCAN TOOL (MUT-III SUB ASSEMBLY)....263
    TREATMENT BEFORE/AFTER DRIVING THROUGH WATER....264
      INSPECTION AND SERVICE BEFORE FORDING A STREAM....264
      INSPECTION AND SERVICE AFTER FORDING A STREAM....266
    TOWING AND HOISTING....267
      WRECKER TOWING RECOMMENDATION....267
      HOISTING....268
    GENERAL DATA AND SPECIFICATIONS....271
    TIGHTENING TORQUE....273
    LUBRICATION AND MAINTENANCE....274
      MAINTENANCE SCHEDULES....274
      SEVERE SERVICE....274
      ENGINE OIL....274
      LUBRICANTS AND GREASES....274
      FUEL USAGE STATEMENT....274
      MATERIALS ADDED TO FUEL....275
    RECOMMENDED LUBRICANTS AND LUBRICANT CAPACITES TABLE....275
      LUBRICANT SELECTION....276
      SELECTION OF COOLANT....278
    SCHEDULED MAINTENANCE TABLE....279
    MAINTENANCE SERVICE....282
      1. FUEL SYSTEM (TANK, PIPE LINE AND CONNECTION AND FUEL TANK FILTER TUBE CAP) (CHECK FOR LEAKS)....282
      2. FUEL HOSES(CHECK CONDITION)....282
      3. AIR CLEANER FILTER (REPLACE)....282
      4. EVAPORATIVE EMISSION CONTROL SYSTEM (CHECK FOR LEAKS AND CLOGGING) (Except evaporative emissio...282
      5. SPARK PLUGS (REPLACE)....283
      6. IGNITION CABLES (REPLACE)....283
      7. TIMING BELT (REPLACE)....283
      8. DRIVE BELT (FOR GENERATOR, WATER PUMP, POWER STEERING OIL PUMP) (CHECK CONDITION)....284
        Water Pump and Generator Drive Belt Tension Check and Adjustment....284
        Power Steering Oil Pump Drive Belt....286
        Air Conditioning Compressor Drive Belt....287
      9. EXHAUST SYSTEM (CONNECTIONS PORTION OF MUFFLER, MUFFLER PIPES AND CONVERTER HEAT SHIELDS) (CHE...288
      10. ENGINE OIL (CHANGE)....289
      11. ENGINE OIL FILTER (REPLACE)....290
      12. TRANSMISSION FLUID (CHECK THE FLUID LEVEL)....290
      13. TRANSFER OIL (CHECK OIL LEVEL) <V4A51>....291
      14. ENGINE COOLANT (CHANGE)....292
      15. COOLANT HOSES (RADIATOR HOSE, HEATER HOSE) (INSPECT)....294
      16. DISC BRAKE PADS, ROTORS (INSPECT FOR WEAR)....294
      17. REAR DRUM BRAKE LININGS AND REAR WHEEL CYLINDERS FOR ALL WHEEL (INSPECT FOR WEAR AND LEAKS)....294
      18. BRAKE HOSES (CHECK FOR DETERIORATION OR LEAKS)....295
      19. BALL JOINT AND STEERING LINKAGE SEALS (INSPECT FOR GREASE LEAKS AND DAMAGE)....295
      20. DRIVE SHAFT BOOTS (INSPECT FOR GREASE LEAKS AND DAMAGE)....295
      21. BALL JOINT WITH GREASE NIPPLE (LUBRICATE GREASE)....296
      22. SUSPENSION SYSTEM (INSPECT FOR LOOSENESS AND DAMAGE)....296
      23. REAR AXLE OIL <with LSD> (CHANGE)....296
      REAR AXLE AND FRONT AXLE <without LSD> (CHECK OIL LEVEL)....297
      24. PROPELLER SHAFT JOINTS WITH GREASE NIPPLE (LUBRICATE GREASE)....297
      25. SRS AIR BAG (INSPECT SYSTEM)....298
        WIRING HARNESS....302
      26. TIRES (ROTATE)....302
    MAIN SEALANT AND ADHESIVE TABLE....303
GR00001100-11....307
  ENGINE....307
GR00001200-11A....309
  ENGINE MECHANICAL....309
    GENERAL DESCRIPTION....310
    ENGINE DIAGNOSIS....311
    SPECIAL TOOLS....312
    ON-VEHICLE SERVICE....315
      DRIVE BELT TENSION CHECK AND ADJUSTMENT....315
      POWER STEERING OIL PUMP DRIVE BELT TENSION CHECK AND ADJUSTMENT....315
      A/C COMPRESSOR DRIVE BELT TENSION CHECK AND ADJUSTMENT....316
      IGNITION TIMING CHECK....317
      CURB IDLE SPEED CHECK....318
      IDLE MIXTURE CHECK....319
      COMPRESSION PRESSURE CHECK....320
      MANIFOLD VACUUM CHECK....321
      LASH ADJUSTER CHECK....321
    ENGINE ASSEMBLY....324
      REMOVAL SERVICE POINTS....327
      INSTALLATION SERVICE POINT....327
    CRANKSHAFT PULLEY....328
      REMOVAL SERVICE POINT....328
      INSTALLATION SERVICE POINT....328
    CAMSHAFT....329
      REMOVAL SERVICE POINTS....330
      INSTALLATION SERVICE POINTS....330
    CAMSHAFT OIL SEAL....331
      REMOVAL SERVICE POINTS....331
      INSTALLATION SERVICE POINTS....332
    OIL PAN AND OIL SCREEN....333
      REMOVAL SERVICE POINT....334
      INSTALLATION SERVICE POINTS....334
      INSPECTION....335
    CRANKSHAFT FRONT OIL SEAL....336
      INSTALLATION SERVICE POINTS....336
    CRANKSHAFT REAR OIL SEAL....337
      REMOVAL SERVICE POINT....338
      INSTALLATION SERVICE POINTS....338
    CYLINDER HEAD GASKET....339
      REMOVAL SERVICE POINT....340
      INSTALLATION SERVICE POINTS....340
    TIMING BELT....342
      REMOVAL SERVICE POINTS....343
      INSTALLATION SERVICE POINTS....344
      INSPECTION....348
        AUTO-TENSIONER....348
    SPECIFICATIONS....348
GR00001600-12....351
  ENGINE LUBRICATION....351
    GENERAL DESCRIPTION....352
    SPECIAL TOOL....352
    ON-VEHICLE SERVICE....353
      ENGINE OIL CHECK....353
      ENGINE OIL REPLACEMENT....353
      ENGINE OIL FILTER REPLACEMENT....353
      ENGINE OIL PRESSURE CHECK....353
    SPECIFICATIONS....354
GR00001800-16....357
  ENGINE ELECTRICAL....357
    CHARGING SYSTEM....359
      CHARGING SYSTEM DIAGNOSIS....360
        TROUBLESHOOTING HINTS....360
        TROUBLESHOOTING GUIDE....360
          STEP 1...360
          STEP 2...360
          STEP 3...360
          STEP 4...361
          STEP 5...361
          STEP 6...361
          STEP 7...361
          STEP 8...361
          STEP 9...361
          STEP 10...362
      ON-VEHICLE SERVICE....363
      WAVE PATTERN CHECK USING AN OSCILLOSCOPE....367
      GENERATOR ASSEMBLY....370
        DISASSEMBLY SERVICE POINTS....372
        ASSEMBLY SERVICE POINTS....373
      INSPECTION....373
    STARTING SYSTEM....376
      OPERATION....376
      STARTING SYSTEM DIAGNOSIS....377
        TROUBLESHOOTING HINTS....377
        TROUBLESHOOTING GUIDE....377
          STEP 1...377
          STEP 2...377
          STEP 3...378
          STEP 4...378
          STEP 5...378
      ON-VEHICLE SERVICE....378
      STARTER RELAY CHECK....378
      STARTER MOTOR ASSEMBLY....379
      INSPECTION....379
        DISASSEMBLY SERVICE POINTS....383
        STARTER MOTOR PART CLEANING....383
        ASSEMBLY SERVICE POINT....383
      INSPECTION....384
    IGNITION SYSTEM....386
      ON-VEHICLE SERVICE....387
      SPARK PLUG CABLE TEST....387
      SPARK PLUG TEST....387
      IGNITION COIL CHECK....388
      IGNITION POWER TRANSISTOR CONTINUITY CHECK....388
      SPARK PLUG CABLE RESISTANCE CHECK....389
      SPARK PLUG CHECK AND CLEANING....389
      CAMSHAFT POSITION SENSOR CHECK....389
      CRANKSHAFT POSITION SENSOR CHECK....389
      IGNITION SECONDARY VOLTAGE WAVE PATTERN CHECK USING AN OSCILLOSCOPE....390
      IGNITION PRIMARY VOLTAGE WAVE PATTERN CHECK USING AN OSCILLOSCOPE....395
      CAMSHAFT POSITION SENSOR AND CRANKSHAFT POSITION SENSOR....400
    SPECIFICATIONS....401
GR00002000-17....403
  ENGINE AND EMISSION CONTROL....403
    ENGINE CONTROL....405
      ENGINE CONTROL SYSTEM DIAGNOSIS....405
      SYMPTOM PROCEDURES....405
      INSPECTION PROCEDURE 1: Throttle Valve will not Fully Open or Close...405
        DIAGNOSIS....405
          STEP 1. Check the accelerator cable adjustment...405
          STEP 2. Check the return spring...405
          STEP 3. Check the throttle lever...405
          STEP 4. Retest the system...405
      INSPECTION PROCEDURE 2: Accelerator Pedal Operation is not Smooth (Over Acceleration)....406
        DIAGNOSIS....406
          STEP 1. Check the accelerator pedal...406
          STEP 2. Check the accelerator cable wiring...406
          STEP 3. Check the accelerator cable lubricant...406
          STEP 4. Retest the system...406
      ON-VEHICLE SERVICE....406
      ACCELERATOR CABLE CHECK AND ADJUSTMENT....406
      ACCELERATOR CABLE AND PEDAL....407
    AUTO-CRUISE CONTROL....408
      CONSTRUCTION DIAGRAM....408
      AUTO-CRUISE CONTROL SYSTEM DIAGNOSIS....409
      AUTO-CRUISE CONTROL SYSTEM DIAGNOSTIC FUNCTION....410
        HOW TO CONNECT THE SCAN TOOL (MUT-III)...410
        HOW TO READ AND ERASE DIAGNOSTIC TROUBLE CODES....411
        HOW TO READ DATA LIST....412
      DIAGNOSTIC TROUBLE CODE PROCEDURES....414
      DTC 11: Auto-cruise Vacuum Pump Drive System....414
        DIAGNOSIS....416
          STEP 1. Measure the output circuit voltage at auto-cruise control-ECU connector C-35 by backprobing...416
          STEP 2. Check auto-cruise control-ECU connector C-35 and intermediate connector C-41 for loose, c...417
          STEP 3. Check auto-cruise control vacuum pump connector A-02 for loose, corroded or damaged termi...417
          STEP 4. Check the auto-cruise vacuum pump...418
          STEP 5. Check the harness wire between auto-cruise control vacuum pump connector A-02 (terminal N...419
          STEP 6. Check the diagnostic trouble codes...419
          STEP 7. Check the diagnostic trouble codes...419
      DTC 12: Vehicle Speed Sensor System....420
        DIAGNOSIS....421
          STEP 1. Check the speedometer...421
          STEP 2. Measure the circuit voltage at auto-cruise control-ECU connector C-35 by backprobing...422
          STEP 3. Check auto-cruise control-ECU connector C-35 for loose, corroded or damaged terminals, or...422
          STEP 4. Check the harness wire between intermediate connector C-29 (terminal No. 8) and auto-crui...423
          STEP 5. Check the diagnostic trouble codes...423
          STEP 6. Check the diagnostic trouble codes...423
      DTC14 : Stoplight Switch System....424
        DIAGNOSIS....425
          STEP 1. Measure the output circuit voltage at stoplight switch connector C-66 by backprobing...425
          STEP 2. Check stoplight switch connector C-66 for loose, corroded or damaged terminals, or termin...426
          STEP 3. Measure the output circuit voltage at stoplight switch connector C-66 by backprobing...426
          STEP 4. Check stoplight switch connector C-66 for loose, corroded or damaged terminals, or termin...426
          STEP 5. Check the stoplight switch...427
          STEP 6. Measure the output circuit voltage at auto-cruise control vacuum pump connector A-02 by b...428
          STEP 7. Check auto-cruise control vacuum pump connector A-02 and intermediate connector C-41 for ...428
          STEP 8. Check the harness wire between stoplight switch connector C-66 (terminal No.1) and auto-c...429
          STEP 9. Measure the output circuit voltage at auto-cruise control-ECU connector C-35 by backprobing...430
          STEP 10. Check auto-cruise control-ECU connector C-35 and intermediate connector C-41 for loose, ...431
          STEP 11. Check auto-cruise control vacuum pump connector A-02 for loose, corroded or damaged term...431
          STEP 12. Check the auto-cruise vacuum pump...432
          STEP 13. Check the harness wire between auto-cruise control vacuum pump connector A-02 (terminal ...433
          STEP 14. Measure the output circuit voltage at auto-cruise control-ECU connector C-35 by backprob...434
          STEP 15. Check intermediate connector C-41 for loose, corroded or damaged terminals, or terminals...434
          STEP 16. Check the harness wire between auto-cruise control-ECU connector C-35 (terminal No.5) an...435
          STEP 17. Check auto-cruise control-ECU connector C-35 for loose, corroded or damaged terminals, o...435
          STEP 18. Check the diagnostic trouble codes...435
          STEP 19. Check the diagnostic trouble codes...436
      DTC15 : Auto-cruise Control Switch System....436
        DIAGNOSIS....438
          STEP 1. Measure the 12-Volt supply circuit voltage at auto-cruise control switch connector D-19...438
          STEP 2. Check auto-cruise control switch connector D-19 for loose, corroded or damaged terminals,...438
          STEP 3. Check the clock spring...438
          STEP 4. Check clock spring connector D-25 for loose, corroded or damaged terminals, or terminals ...439
          STEP 5. Check the harness wire between multi-purpose fuse No.4 and auto-cruise control switch con...439
          STEP 6. Measure the output circuit voltage at auto-cruise control switch connector D-19 by backpr...440
          STEP 7. Check auto-cruise control switch connector D-19 for loose, corroded or damaged terminals,...440
          STEP 8. Check the auto-cruise control switch...441
          STEP 9. Measure the output circuit voltage at auto-cruise control-ECU connector C-35 by backprobing...442
          STEP 10. Check auto-cruise control-ECU connector C-35 for loose, corroded or damaged terminals, o...442
          STEP 11. Check the clock spring...443
          STEP 12. Check auto-cruise control switch connector D-19, clock spring connector D-25 for loose, ...443
          STEP 13. Check the harness wire between auto-cruise control switch connector D-19 (terminal No.2 ...443
          STEP 14. Check the diagnostic trouble codes...444
          STEP 15. Check the diagnostic trouble codes...444
      DTC 16: Auto-cruise Control-ECU....444
        DIAGNOSIS....444
      DTC 17: Throttle Position Sensor, Idle Position Signal System....445
        DIAGNOSIS....447
          STEP 1. Check the throttle position sensor...447
          STEP 2. Measure the output circuit voltage at auto-cruise control-ECU connector C-35 by backprobing...448
          STEP 3. Check auto-cruise control-ECU connector C-35 for loose, corroded or damaged terminals, or...448
          STEP 4. Check the harness wire between throttle position sensor connector A-41 (terminal No.3) an...449
          STEP 5. Measure the output circuit voltage at PCM connector C-91 (terminal No.79)...450
          STEP 6. Check PCM connector C-91, auto-cruise control-ECU connector C-35, intermediate connector ...451
          STEP 7. Check the harness wire between PCM connector C-91 (terminal No.79) and auto-cruise contro...453
          STEP 8. Measure the output circuit voltage at auto-cruise control-ECU connector C-35 by backprobing...454
          STEP 9. Check the diagnostic trouble codes...454
          STEP 10. Check the diagnostic trouble codes...454
      SYMPTOM PROCEDURES....456
      INSPECTION PROCEDURE 1: Communication with Scan Tool MB991958 is not Possible (Communication with...456
        DIAGNOSIS....458
          STEP 1. Measure the output circuit voltage at auto-cruise control-ECU connector C-35 by backprobing...458
          STEP 2. Check auto-cruise control-ECU connector C-35 for loose, corroded or damaged terminals, or...458
          STEP 3. Check junction block connector D-08 and D-06 for loose, corroded or damaged terminals, or...459
          STEP 4. Check the harness wire between ignition switch and auto-cruise control-ECU connector C-35...459
          STEP 5. Measure the ground circuit voltage at auto-cruise control-ECU connector C-35 by backprobing...460
          STEP 6. Check auto-cruise control-ECU connector C-35 for loose, corroded or damaged terminals, or...460
          STEP 7. Check the harness wire between auto-cruise control-ECU connector C-35 (terminal No.14) an...461
          STEP 8. Check data link connector C-69 for loose, corroded or damaged terminals, or terminals pus...461
          STEP 9. Check auto-cruise control-ECU connector C-35 for loose, corroded or damaged terminals, or...462
          STEP 10. Check the harness wire between auto-cruise control-ECU connector C-35 (terminal No.11) a...462
          STEP 11. Check that the malfunction is eliminated...463
          STEP 12. Check that the malfunction is eliminated...463
      INSPECTION PROCEDURE 2: When the Brake Pedal is Depressed, Auto-cruise Control is not Cancelled...464
        DIAGNOSIS....466
          STEP 1. Check if the stoplight illuminates...466
          STEP 2. Measure the output circuit voltage at stoplight switch connector C-66 by backprobing...466
          STEP 3. Check stoplight switch connector C-66 for loose, corroded or damaged terminals, or termin...466
          STEP 4. Check junction connector D-02 and D-09 for loose, corroded or damaged terminals, or termi...467
          STEP 5. Check the harness wire between fusible link No.8 and stoplight switch connector C-66 (ter...467
          STEP 6. Check the stoplight switch...468
          STEP 7. Check the harness wire between stoplight switch connector C-66 (terminal No. 3) and joint...469
          STEP 8. Measure the output circuit voltage at auto-cruise control-ECU connector C-35 by backprobing...470
          STEP 9. Check auto-cruise control-ECU connector C-35, stoplight switch connector C-66 and joint c...471
          STEP 10. Check the harness wire between stoplight switch connector C-66 (terminal No.3) and auto-...472
          STEP 11. Check that the malfunction is eliminated...472
          STEP 12. Check that the malfunction is eliminated...472
      INSPECTION PROCEDURE 3: When the Selector Lever is Moved to "N" Range, Auto-cruise Control is not...473
        DIAGNOSIS....475
          STEP 1. Measure the signal voltage at auto-cruise control-ECU connector C-35 by backprobing...475
          STEP 2. Check park/neutral position switch connector B-01, intermediate connector C-30 and auto-c...476
          STEP 3. Check the circuit at the park/neutral position switch...477
          STEP 4. Check the harness wire between park/neutral position switch connector B-01 (terminal No.1...478
          STEP 5. Check that the malfunction is eliminated....478
          STEP 6. Check that the malfunction is eliminated....478
      INSPECTION PROCEDURE 4: When the Auto-cruise Control "CANCEL" Switch is Set to ON, Auto-cruise Co...479
        DIAGNOSIS....479
      INSPECTION PROCEDURE 5: Auto-cruise Control cannot be Set...479
        DIAGNOSIS....479
          STEP 1. Can the auto-cruise control-ECU communicate with scan tool MB991958?....480
          STEP 2. Using scan tool MB991958, check the any DTC set...480
          STEP 3. Using scan tool MB991958, check data list item 04: auto-cruise control "CANCEL" switch...481
          STEP 4. Using scan tool MB991958, check data list item 05: stoplight switch...481
          STEP 5. Using scan tool MB991958, check data list item 14: park/neutral position switch...482
          STEP 6. Check that the malfunction is eliminated....482
          STEP 7. Check that the malfunction is eliminated....482
      INSPECTION PROCEDURE 6: Hunting (Repeated Acceleration and Deceleration) Occurs at the Set Vehicl...483
        DIAGNOSIS....483
          STEP 1. Check the vehicle speed sensor...483
          STEP 2. Check the auto-cruise vacuum pump...484
          STEP 3. Check the vacuum actuator...484
          STEP 4. Check that the malfunction is eliminated....485
          STEP 5. Check that the malfunction is eliminated....485
      INSPECTION PROCEDURE 7: Auto-cruise Control Indicator Light inside Combination Meter does not Ill...486
        DIAGNOSIS....488
          STEP 1. Check the auto-cruise control indicator bulb...488
          STEP 2. Measure the output circuit voltage at auto-cruise control-ECU connector C-35 by backprobing...488
          STEP 3. Measure the output circuit voltage at junction block connector D-06 by backprobing...489
          STEP 4. Check junction block connector D-06 for loose, corroded or damaged terminals, or terminal...489
          STEP 5. Check combination meter connector C-04 and C-05 for loose, corroded or damaged terminals,...490
          STEP 6. Check the harness wire between combination meter connector C-04 (terminal No.24) and junc...490
          STEP 7. Check the combination meter...491
          STEP 8. Check auto-cruise control-ECU connector C-35 for loose, corroded or damaged terminals, or...491
          STEP 9. Check the harness wire between combination meter connector C-05 (terminal No.8) and auto-...492
          STEP 10. Check that the malfunction is eliminated....492
          STEP 11. Check that the malfunction is eliminated....492
      ON-VEHICLE SERVICE....497
      AUTO-CRUISE CONTROL SWITCH CHECK....497
        AUTO-CRUISE CONTROL MAIN SWITCH CHECK....497
        AUTO-CRUISE CONTROL SETTING....498
        SPEED-INCREASE SETTING....498
        SPEED-REDUCTION SETTING....498
        RETURN TO THE SET SPEED BEFORE CANCELLATION AND AUTO-CRUISE CONTROL CANCELLATION....499
      AUTO-CRUISE CONTROL SYSTEM COMPONENT CHECK....499
        STOPLIGHT SWITCH....499
        PARK/NEUTRAL POSITION SWITCH ("N" POSITION)....499
        THROTTLE POSITION SENSOR....499
        AUTO-CRUISE VACUUM PUMP....500
        VACCUM ACTUATOR CHECK....500
        VEHICLE SPEED SENSOR CHECK....500
      AUTO-CRUISE CONTROL....501
      AUTO-CRUISE CONTROL SWITCH CHECK....503
    EMISSION CONTROL....504
      VACUUM HOSES....505
      VACUUM HOSE INSTALLATION....507
      VACUUM HOSE CHECK....507
      POSITIVE CRANKCASE VENTILATION SYSTEM....507
      POSITIVE CRANKCASE VENTILATION SYSTEM CHECK....508
      POSITIVE CRANKCASE VENTILATION VALVE CHECK....508
      EVAPORATIVE EMISSION CONTROL SYSTEM....509
      EVAPORATIVE EMISSION PURGE SOLENOID CHECK....511
      VOLUME AIRFLOW SENSOR CHECK....512
      BAROMETRIC PRESSURE SENSOR CHECK....512
      ENGINE COOLANT TEMPERATURE SENSOR CHECK....512
      INTAKE AIR TEMPERATURE SENSOR CHECK....512
      FUEL TANK DIFFERENTIAL PRESSURE SENSOR CHECK....512
      EVAPORATIVE EMISSION VENTILATION SOLENOID CHECK....512
      EXHAUST GAS RECIRCULATION (EGR) SYSTEM....513
        OPERATION....513
      EXHAUST GAS RECIRCULATION SYSTEM CHECK....514
      VACUUM CONTROL VALVE CHECK....515
      EGR VALVE CHECK....515
      EGR PORT VACUUM CHECK....516
      EGR VACUUM REGULATOR SOLENOID VALVE CHECK....516
      VOLUME AIRFLOW SENSOR CHECK....517
      ENGINE COOLANT TEMPERATURE SENSOR CHECK....517
      CRANKSHAFT POSITION SENSOR CHECK....517
      EVAPORATIVE EMISSION CANISTER AND FUEL TANK PRESSURE RELIEF VALVE....518
      INSPECTION....519
        EVAPORATIVE EMISSION VENTILATION SOLENOID CHECK....519
      CATALYTIC CONVERTER....520
        REMOVAL SERVICE POINT....521
        INSTALLATION SERVICE POINT....521
    SPECIFICATIONS....522
GR00002100-11B....523
  GROUP 11B....523
  ENGINE OVERHAUL....523
    CONTENTS....523
  REMOVAL AND INSTALLATION....526
    REMOVAL SERVICE POINT....527
      1. Using special tool MD998781, hold the drive plate...527
      2. Remove the crankshaft bolt...527
    INSTALLATION SERVICE POINT....527
      1. Using special tool MD998781, hold the drive plate...527
      2. Clean the bolt hole in crankshaft bolt and dam....527
      3. Degrease the cleaned seating surface of the damper pulley...527
      4. Install the damper pulley...527
      5. Apply oil to the threads of crankshaft bolt and the outer surface of washer...527
      6. Install the washer to the crankshaft bolt with its inside chamfered side toward the bolt head...527
      7. Tighten the crankshaft bolt to the specified torque...527
  REMOVAL AND INSTALLATION....528
    INSTALLTION SERVICE POINT....529
  REMOVAL AND INSTALLATION....529
  REMOVAL AND INSTALLATION....530
    REMOVAL SERVICE POINTS....531
      <<B>> CAMSHAFT SPROCKET BOLT REMOVAL....531
    INSTALLATION SERVICE POINTS....531
      >>B<< CRANKSHAFT SENSING BLADE/CRANKSHAFT SPACER/CRANKSHAFT SPROCKET INSTALLATION....532
        1. Clean the hole in the crankshaft sprocket...532
        2. Clean and degrease the mating surfaces of the crankshaft sprocket, sensing blade, and spacer...532
      >>C<< AUTO-TENSIONER INSTALLATION....532
        1. Set the auto-tensioner in a vice...532
        2. Slowly close the vice to force the rod in until set hole (A) of the rod is lined up with set h...532
        3. Insert a wire [1.4 mm (0.06 inch) in diameter] into the set holes...532
        4. Remove the auto-tensioner from the vice...532
      >>D<< TIMING BELT INSTALLATION....532
        1. Move the timing mark of the crankshaft sprocket three teeth to slightly lower the piston below...532
        2. Line up the timing marks of the left bank camshaft sprocket...532
        3. Line up the timing marks of the right bank camshaft sprocket...532
        4. Line up the timing marks of the crankshaft sprockets...533
        5. Install the timing belt on each sprocket in the following sequence...533
        (1) Install the timing belt on the crankshaft sprocket and then on the idler pulley, while tighte...533
        (2) Install the timing belt on the left bank camshaft sprocket...533
        (3) Install the timing belt on the water pump pulley, while taking up the slack...533
        (4) Install the timing belt on the right bank camshaft sprocket...533
        (5) Install the timing belt on the tensioner pulley...533
        6. Lightly press the tensioner pulley against the belt and temporarily tighten the center bolt...533
        7. Check to see that the timing marks of all the sprockets are in alignment...533
        8. Using special tool MD998769, rotate the crankshaft a quarter of a turn counterclockwise. Then ...533
        9. Mount special tool MD998767 and torque wrench on the tensioner pulley...534
        10. Torque it to 4.4 Nm (39 in-lb) with the torqu....534
        11. While holding the tensioner pulley in position, tighten the center bolt to the specified torque...534
        12. Rotate the crankshaft two turns clockwise and leave it alone for approximately five minutes...534
        13. Check to see whether the metal wire inserted when the auto-tensioner was installed can be rem...534
        If the metal wire can be removed without any resistance, it means that the belt has a proper tens...534
        14. If the metal wire offers resistance when removed, repeat the previous steps 9 through 12 unti...534
  INSPECTION....535
    TIMING BELT....535
      1. Hardening of rubber backing...535
      Back side is glossy without resilience and leaves no indent when pressed with fingernail...535
      2. Cracks on rubber back...535
      3. Cracks or peeling of canvas...535
      4. Cracks on tooth bottom...535
      5. Cracks on belt...535
      6. Abnormal wear of belt sides. Normal wear is indicated if the sides are sharp as if cut by a kn...535
      7. Abnormal wear on teeth...535
      8. Missing tooth...535
    TENSIONER PULLEY AND IDLER PULLEY....536
    AUTO-TENSIONER....536
      1. Check for oil leaks. If oil leaks are evident, replace the auto-tensioner...536
      2. Check the rod end for wear or damage and replace the auto-tensioner if necessary...536
      3. Measure the rod protrusion. If it is out of specification, replace the auto-tensioner...536
      4. Press the rod with a force of 98 to 196 N (22 to 44 pounds) and measure the movement of the rod...536
      If the measured value is out of the standard value, replace the auto-tensioner...536
  REMOVAL AND INSTALLATION....537
    INSTALLATION SERVICE POINTS....539
      1. Tighten the nuts on the right bank to 6.5 ± 1 ....539
      2. Tighten the nuts on the left bank to the specified torque...539
      3. Tighten the nuts on the right bank to the specified torque...539
      4. Tighten the nuts on the left bank and those on the right bank again in that order...539
      >>B<< INJECTOR INSTALLATION....539
        1. Before installing the injector, lubricate the O-ring with a drop of new engine oil for easy in...539
        2. Insert the injector top end into the fuel rail. Be careful not to damage the O-ring during ins...539
      >>C<< FUEL PRESSURE REGULATOR INSTALLATION....539
      >>D<< O-RING AND WATER PIPE INSTALLATION....539
      >>E<< THERMOSTAT INSTALLATION....540
      >>F<< SEALANT APPLICATION TO ENGINE COOLANT TEMPERATURE SENSOR....540
      >>G<< SEALANT APPLICATION TO ENGINE COOLANT TEMPERATURE GAUGE UNIT....540
  REMOVAL AND INSTALLATION....541
  REMOVAL AND INSTALLATION....542
    REMOVAL SERVICE POINT....543
    INSTALLATION SERVICE POINTS....543
      1. Apply engine oil to the camshaft journals and cams and then install the camshafts...543
      2. Check to see that the dowel pin of the camshaft is located at the position shown...543
      >>B<< LASH ADJUSTER INSTALLATION....544
      >>C<< ROCKER ARM, ROCKER ARM SHAFT AND ROCKER SHAFT SPRING INSTALLATION....544
        1. Temporarily tighten the rocker shaft with bolts so that all the intake valve rocker arms do no...544
        2. Insert the rocker shaft spring from above and mount it at right angles to the plug guide...544
        3. Make sure that the notch of the rocker shaft is in the position shown in the illustration...544
      >>D<< CAMSHAFT OIL SEAL INSTALLATION....545
  INSPECTION....545
    ROCKER ARM SHAFT....545
    ROCKER ARM....545
      1. Check the roller surface and replace the rocker arm if recesses, damage or heat seizure is obs...545
      2. Check roller rotation and replace the rocker arm if uneven rotation or roller backlash of the ...545
      3. Check the inside diameter and replace the rocker arm if damage or seizure is observed...545
    CAMSHAFT....545
      1. Check the camshaft bearing journals for damage and binding. If the journals are binding, check...545
      2. Check the tooth surface of the distributor drive gear teeth of the camshaft and replace if abn...545
      3. Check the cam surface for abnormal wear and damage and replace if necessary. Also measure the ...546
    LASH ADJUSTERS....546
      1. Prepare three containers and approximately 5 dm3 (30.5 quart) of diesel fuel. Into each contai...546
      2. Place the lash adjuster in container A and clean its outside surface...546
      3. While gently pushing down the internal steel ball using wire [0.5 mm (0.020 inch) in diameter]...546
      4. Remove the lash adjuster from the container. Then, push down the steel ball gently and push th...547
      5. Place the lash adjuster in container B. Then, gently push down the internal steel ball using a...547
      6. Remove the lash adjuster from the container. Then, push down the steel ball gently and push th...547
      7. Place the lash adjuster in container C. Then, gently push down the internal steel ball using a...547
      8. Stand the lash adjuster with its plunger at the top, then push the plunger downward firmly unt...547
      9. Remove the lash adjuster from the container, then stand the lash adjuster with its plunger at ...548
      10. Stand the lash adjuster upright to prevent diesel fuel from spilling out. Do not allow the la...548
  REMOVAL AND INSTALLATION....549
    REMOVAL SERVICE POINTS....550
      <<B>> RETAINER LOCK REMOVAL....550
        1. Using special tool MD998735 or MD998772, compress the spring...550
        2. Remove the retainer locks...550
    INSTALLATION SERVICE POINTS....550
      1. Install the valve spring seat...550
      2. Using special tool MD998774, install a new stem seal to the valve guide...551
      >>B<< VALVE SPRING INSTALLATION....551
      >>C<< RETAINER LOCK INSTALLATION....552
      >>D<< CYLINDER HEAD BOLT INSTALLATION....552
        1. Tighten the bolts in two or three rounds stages in the illustrated sequence...552
        2. Back off the bolts once and tighten them again to the specified torque in step 1...552
  INSPECTION....552
    CYLINDER HEAD....553
      1. Check the cylinder head gasket surface for flatness by using a straightedge in the directions ...553
      2. If the service limit is exceeded, correct to meet the specification...553
      3. *If the service limit is exceeded, correct to meet the specification...553
    VALVE....553
      1. Check the valve face for correct contact. If incorrect, reface using a valve refacer. The valv...553
      2. If the margin exceeds the service minimum limit, replace the valve...553
      3. Measure the valve's total length. If the measurement is less than specified, replace the valve...553
    VALVE SPRINGS....553
      1. Measure the free height of the spring and, if it is smaller than the minimum limit, replace th...553
      2. Measure the squareness of the spring and, if the limit is exceeded, replace the spring...553
    VALVE GUIDES....554
    VALVE SEAT....554
    VALVE SEAT RECONDITIONING PROCEDURE....554
      1. Using the special tool or a seat grinder, correct to obtain the specified seat width and angle...554
      2. After correcting the valve seat, lap the valve and valve seat using lapping compound. Then, ch...554
    VALVE SEAT REPLACEMENT PROCEDURE....554
      1. Cut the valve seat from the inside to thin the wall thickness. Then, remove the valve seat...554
      2. Rebore the valve seat hole in the cylinder head to a selected oversize valve seat diameter...555
      3. Before fitting the valve seat, either heat the....555
      4. Using a valve seat cutter, correct the valve seat to the specified width and angle. Using a va...555
    VALVE GUIDE REPLACEMENT PROCEDURE....555
      1. Remove the snap ring from the exhaust valve guide...555
      2. Using a press, remove the valve guide toward the cylinder head gasket surface...555
      3. Re bore the valve guide hole of the cylinder head so that it fits the press-fitted oversize va...555
      4. Install the new snap ring into the groove of exhaust valve guide...555
      5. Press-fit the valve guide until it protrudes 14 mm (0.55 inch) from the cylinder head top surf...555
  REMOVAL AND INSTALLATION....556
    REMOVAL SERVICE POINTS....557
      1. Remove the lower oil pan mounting bolts...557
      2. Remove the lower oil pan by tapping on its side wall a plastic hammer (mallet) through a wood ...557
      <<B>> UPPER OIL PAN REMOVAL....557
        1. Remove the bolts A shown in the illustration first...557
        2. Remove all other bolts...557
        3. Remove the oil pan...557
        4. Thread the bolt into the illustrated bolt hole B to remove the oil pan...557
      <<C>> OUTER ROTOR/INNER ROTOR REMOVAL....557
    INSTALLATION SERVICE POINTS....558
      >>B<< OIL PUMP CASE INSTALLATION....558
        1. Clean the gasket surfaces of oil pump case and cylinder block...558
        2. Apply a 3mm (0.12 inch) diameter bead of sealant Mitsubishi Genuine Parts number MD970389, or ...558
        3. Tighten the oil pump case bolts to specified torque...558
        4. After installation, keep the sealed area away from the oil for approximately one hour...558
      >>C<< CRANKSHAFT OIL SEAL INSTALLATION....558
        1. Install the guide of special tool MD998717 to the front end of the crankshaft...558
        2. Apply engine oil to the lip area of a new oil seal and push it in until it contacts the oil pu...558
        3. Using special tool MD998717, press-fit the oil seal into the oil pump case...558
      >>D<< UPPER OIL PAN INSTALLATION....559
        1. Clean the gasket surfaces of the cylinder block and upper oil pan...559
        2. Apply a 4 mm (0.2 inch) diameter bead of sealant Mitsubishi Genuine Parts number MD970389, or ...559
        3. Tighten the upper oil pan bolts in the sequence shown...559
        4. After installation, keep the sealed area away from the oil for approximately one hour...559
      >>E<< LOWER OIL PAN INSTALLATION....559
        1. Clean the gasket surfaces of the upper and lower oil pan...559
        2. Apply a 4 mm (0.2 inch) diameter bead of sealant Mitsubishi Genuine Parts number MD970389, or ...559
        3. Tighten the lower oil pan bolts in the sequence shown...559
        4. After installation, keep the sealed area away from the oil for approximately one hour...559
      >>F<< DRAIN PLUG GASKET INSTALLATION....560
      >>G<< OIL FILTER INSTALLATION....560
        1. Clean the installation surface of the oil filter bracket...560
        2. Apply engine oil to the O-ring of the oil filter...560
        3. Screw the oil filter on until the O-ring conta....560
      >>H<< SEALANT APPLICATION TO OIL PRESSURE GAUGE UNIT....560
        1. Apply 3M‰ AAD Part number 8672 or equivalent t....560
        2. Tighten the oil pressure switch together with the oil filter bracket to the specified torque, ...561
  INSPECTION....561
    OIL PUMP....561
      1. Check the tip clearance...561
      2. Check the side clearance...561
      3. Check the body clearance...561
  REMOVAL AND INSTALLATION....562
    REMOVAL SERVICE POINTS....563
      1. Mark the cylinder number on the side of the connecting rod big end for correct reassembly...563
      2. Keep the removed connecting rods, caps, and bearings in order according to the cylinder number...563
      <<B>> PISTON PIN REMOVAL....563
        1. Remove the snap rings...563
        2. Heat the piston approximately 70∞C (158∞F) and....563
    INSTALLATION SERVICE POINTS....563
      1. When replacing the piston, note cylinder bore size mark on the cylinder block as illustrated, ...563
      2. Set the snap ring into one side of the piston pin hole...563
      3. Heat the piston to approximately 70∞C (158∞F)...564
      4. With the front mark of the connecting rod and that of the piston located on the same side, ins...564
      5. Set the snap ring into the other side of the piston pin hole...564
      6. Check that the piston moves smoothly...564
      >>B<< OIL RING INSTALLATION....564
        1. Fit the oil ring spacer into the piston ring groove...564
        2. Install the upper side rail...565
        To install the side rail, first fit one end of the rail into the piston groove, then press the re...565
        3. Install the lower side rail in the same procedure as described in step 2...565
        4. Make sure that the side rails move smoothly in both directions...565
      >>C<< PISTON RING NO.2/PISTON RING NO.1 INSTALLATION....565
        1. To prevent wrong installation, check the identification mark of each piston ring. The identifi...565
        2. Using a piston ring expander, fit the number 2 piston ring into the number 2 groove of piston...565
        3. Install the number 1 piston ring in the same manner as step 2...565
      >>D<< CONNECTING ROD BEARING INSTALLATION....565
        1. Measure the crankshaft pin diameter and confirm its classification from the following table. I...565
        2. From the following table, select a bearing whose size is appropriate for the crankshaft pin ou...566
        If the crankshaft pin outside diameter Identification color is "yellow" and the connecting rod Id...566
        For example, select a bearing whose Identification color is "green."....566
        If there is no Identification color paint on the crankshaft, measure the pin outside diameter and...566
        3. Install the selected bearing in the big end and in the cap of the connecting rod...566
      >>E<< PISTON AND CONNECTING ROD INSTALLATION....566
        1. Liberally coat the circumference of the piston, piston ring, and oil ring with engine oil...566
        2. Arrange the piston ring and oil ring gaps (side rail and spacer) as shown in the illustration...566
        3. Rotate the crankshaft so that the crank pin is on the center of the cylinder bore...566
        4. Insert the piston and connecting rod assembly into the cylinder with the front mark on the pis...567
        5. Using a suitable piston ring compressor tool, install the piston and connecting rod assembly i...567
      >>F<< CONNECTING ROD CAP INSTALLATION....567
        1. Verifying the mark made during disassembly, install the bearing cap to the connecting rod. If ...567
        2. Make sure that the connecting rod big end side clearance meets the specification...567
      >>G<< CONNECTING ROD CAP NUT INSTALLATION....567
        1. The connecting rod bolts should be examined before reuse. If the bolt threads are damaged, the...567
        Hand-thread the nut to the full length of the bolt threads. If the nut does not run down smoothly...567
        2. Before installation of each nut, apply engine oil to the threaded portion and bearing surface ...568
        3. Loosely tighten each nut to the bolt...568
        4. Then tighten the nuts alternately to a torque ....568
        5. Make a paint mark on the head of each nut...568
        6. Make a paint mark on the bolt end at the position 90 degrees to 94 degrees from the paint mark...568
        7. Turn the nut further 90 to 94 degrees and make sure that the paint marks on the nut and bolt a...568
  INSPECTION....568
    PISTON....568
    PISTON PIN....568
      1. Insert the piston pin into the piston pin hole with a thumb. You should feel a slight resistan...568
      2. The piston and piston pin must be replaced as an assembly...568
    PISTON RING....568
      1. Check the piston ring for damage, excessive wear, and breakage and replace if defects are evid...568
      2. Check for clearance between the piston ring and ring groove. If the limit is exceeded, replace...568
      3. Insert the piston ring into the cylinder bore. Force the ring down with a piston, the piston c...569
      If the ring gap is excessive, replace the piston ring...569
    CRANKSHAFT PIN OIL CLEARANCE <PLASTIC GAUGING MATERIAL METHOD>....569
      1. Remove oil from the crankshaft pin and the bearing inner surface...569
      2. Cut plastic gauging material to the same length as the width of the bearing and place it on th...569
      3. Install the connecting rod cap carefully and tighten the nuts to the specified torque...569
      4. Carefully remove the connecting rod cap...569
      5. Measure the width of the smashed plastic gauging material at its widest section by using a sca...569
  REMOVAL AND INSTALLATION....570
    INSTALLATION SERVICE POINTS....571
      1. Measure the crankshaft journal diameter and confirm its classification from the following tabl...571
      2. The cylinder block bearing bore diameter identification marks are stamped at the position show...571
      3. From the above table, select a bearing whose size is appropriate for the crankshaft journal ou...571
      If there is no Identification color paint on the crankshaft, measure the journal outside diameter...571
      4. Install bearings with the groove toward the cylinder block...572
      5. Install the bearings having no groove to the bearing cap...572
      >>B<< CRANKSHAFT THRUST BEARING INSTALLATION....572
        1. Install the thrust bearing in the No.3 bearing bore in the cylinder block and in the bearing c...572
        2. The thrust bearings must be installed with their groove toward the crankshaft web...572
      >>C<< BEARING CAP/BEARING CAP BOLT INSTALLATION....572
        1. Attach the bearing cap on the cylinder block as shown in the illustration...572
        2. Tighten the bearing cap bolts to specified torque in the sequence shown in the illustration...572
        3. Check that the crankshaft rotates smoothly...572
        4. Check the end play. If it exceeds the limit value, replace the thrust bearing...573
      >>D<< CRANKSHAFT REAR OIL SEAL INSTALLATION....573
      >>E<< OIL SEAL CASE INSTALLATION....573
        1. Apply the sealant Mitsubishi Genuine Part number MD970389 or equivalent to the oil seal case...573
        2. Apply a small amount of engine oil to the entire circumference of the oil seal lip section, an...573
  INSPECTION....574
    CRANKSHAFT JOURNAL OIL CLEARANCE <PLASTIC GAUGING MATERIAL METHOD>....574
      1. Remove oil from the crankshaft journal and crankshaft bearing inner surface...574
      2. Install the crankshaft...574
      3. Cut plastic gauging material to the same length as the width of the bearing and place it on th...574
      4. Install the crankshaft bearing cap carefully and tighten the bolts to the specified torque...574
      5. Carefully remove the crankshaft bearing cap...574
      6. Measure the width of the smashed plastic gauging material at its widest section by using a sca...574
    CRANKSHAFT REAR OIL SEAL....574
      1. Check the oil seal lip for wear and damage...574
      2. Check the rubber for deterioration or hardening...574
      3. Check the oil seal case for cracks and damage...574
    CYLINDER BLOCK....574
      1. Visually check for scratches, rust, and corrosion. Use also a flaw detecting agent for the che...574
      2. Using a straightedge and feeler gauge, check the block top surface for warpage. Make sure that...574
      3. If the distortion is excessive, correct within the allowable limit or replace...574
      4. Check the cylinder walls for scratches and seizure. If defects are evident, correct (bored to ...575
      5. Using a cylinder gauge, measure the cylinder bore and cylindricality. If worn badly, correct b...575
    BORING CYLINDER....575
      1. Oversize pistons to be used should be determined on the basis of the largest bore cylinder...575
      2. Measure the outside diameter of the piston to be used. Measure it in the thrust direction as s...575
      3. Based on the measured piston Outside Diameter (OD), calculate the boring finish dimension...575
      4. Bore all cylinders to the calculated boring finish dimension...575
      5. Hone to the final finish dimension (piston OD + clearance between piston OD and cylinder)...575
      6. Check the clearance between the piston and cylinder...575
  REMOVAL AND INSTALLATION....576
  FASTENER TIGHTENING SPECIFICATIONS....577
  GENERAL SPECIFICATIONS....579
  SERVICE SPECIFICATIONS....580
  SEALANTS AND ADHESIVES....582
GR00003300-13....583
  FUEL....583
GR00003400A-13A....585
  MULTIPORT FUEL INJECTION (MFI)....585
    GENERAL DESCRIPTION....586
    MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS....588
      HOW TO CONNECT THE SCAN TOOL (MUT-III)....592
      HOW TO READ AND ERASE DIAGNOSTIC TROUBLE CODE....592
      PROVISIONAL DTCs [SCAN TOOL MB991958 OBD-II Test Mode - Results (Mode 5)]....593
      DIAGNOSTIC BY DIAGNOSTIC TEST MODE II (INCREASED SENSITIVITY)....595
      INSPECTION USING SCAN TOOL MB991958, DATA LIST AND ACTUATOR TESTING....596
      SYSTEM READINESS TEST STATUS....608
      DIAGNOSTIC TROUBLE CODE PROCEDURES....617
      DTC P0101: Volume Airflow Circuit Range / Performance Problem....617
        Logic Flow Chart....619
        Logic Flow Chart....620
        DIAGNOSIS....620
          STEP 1. Using scan tool MB991958, check data list item 12: Volume Airflow Sensor...621
          STEP 2. Measure the reset signal voltage at volume airflow sensor connector A-01 by backprobing...621
          STEP 3. Check connector A-01 at volume airflow sensor and connector C-89 at PCM for damage...622
          STEP 4. Check for short circuit to ground between volume airflow sensor connector A-01 (terminal ...623
          STEP 5. Measure the reset signal voltage at volume airflow sensor connector A-01 by backprobing...623
          STEP 6. Check connector A-01 at volume airflow sensor and connector C-89 at PCM for damage...624
          STEP 7. Check for open circuit and harness damage between volume airflow sensor connector A-01 (t...625
          STEP 8. Replace the volume airflow sensor...625
          STEP 9. Test the OBD-II drive cycle...625
      DTC P0102: Volume Airflow Circuit Low Input....626
        Logic Flow Chart....628
        DIAGNOSIS....628
          STEP 1. Using scan tool MB991958, check data list item 12: Volume Airflow Sensor...629
          STEP 2. Measure the power supply voltage at volume airflow sensor connector A-01 by backprobing...629
          STEP 3. Measure the power supply voltage at volume airflow sensor harness side connector A-01...630
          STEP 4. Check connector A-01 at the volume airflow sensor for damage...630
          STEP 5. Check connector A-01 at volume airflow sensor for damage...631
          STEP 6. Measure the sensor supply voltage at volume airflow sensor harness side connector A-01...631
          STEP 7. Check connector C-90 at PCM for damage...631
          STEP 8. Check for short circuit to ground between volume airflow sensor connector A-01 (terminal ...632
          STEP 9. Check for continuity at volume airflow sensor harness side connector A-01...632
          STEP 10. Check connector C-90 at PCM for damage...633
          STEP 11. Check for open circuit and harness damage between volume airflow sensor connector A-01 (...634
          STEP 12. Check connector C-90 at PCM for damage...634
          STEP 13. Test the OBD-II drive cycle...634
      DTC P0106: Manifold Absolute Pressure Circuit Range/Performance Problem....635
        Logic Flow Chart....637
        Logic Flow Chart....638
        DIAGNOSIS....639
          STEP 1. Using scan tool MB991958, check data list item 95: Manifold Absolute Pressure Sensor...639
          STEP 2. Measure the sensor supply voltage at manifold absolute pressure sensor connector A-12 by ...640
          STEP 3. Measure the sensor supply voltage at PCM connector C-90 by backprobing...640
          STEP 4. Check connector A-12 at the manifold absolute pressure sensor and connector C-90 at PCM f...641
          STEP 5. Check connector A-12 at the manifold absolute pressure sensor and connector C-90 at PCM f...642
          STEP 6. Measure the ground voltage at manifold absolute pressure sensor connector A-12 by backpro...642
          STEP 7. Check connector A-12 at the manifold absolute pressure sensor and connector C-90 at PCM f...643
          STEP 8. Check for harness damage between manifold absolute pressure sensor connector A-12 (termin...644
          STEP 9. Check connector A-12 at manifold absolute pressure sensor for damage...644
          STEP 10. Check connector C-91 at PCM for damage...645
          STEP 11. Check for short circuit to ground and harness damage between manifold absolute pressure ...645
          STEP 12. Test the OBD-II drive cycle...646
      DTC P0107: Manifold Absolute Pressure Circuit Low Input....646
        Logic Flow Chart....648
        DIAGNOSIS....649
          STEP 1. Using scan tool MB991958, check data list item 95: Manifold Absolute Pressure Sensor...649
          STEP 2. Measure the sensor output voltage at manifold absolute pressure sensor connector A-12 by ...650
          STEP 3. Measure the sensor output voltage at PCM connector C-91 by backprobing...651
          STEP 4. Check connector A-12 at the manifold absolute pressure sensor and connector C-91 at PCM f...652
          STEP 5. Using scan tool MB991958, check data list item 95: Manifold Absolute Pressure Sensor...653
          STEP 6. Check connector A-12 at the manifold absolute pressure sensor and connector C-91 at PCM f...654
          STEP 7. Measure the sensor supply voltage at manifold absolute pressure sensor connector A-12 by ...654
          STEP 8. Measure the sensor supply voltage at PCM connector C-90 by backprobing...655
          STEP 9. Check connector A-12 at the manifold absolute pressure sensor and connector C-90 at PCM f...656
          STEP 10. Check connector A-12 at the manifold absolute pressure sensor and connector C-90 at PCM ...657
          STEP 11. Check for short circuit to ground between manifold absolute pressure sensor connector A-...658
          STEP 12. Measure the ground voltage at manifold absolute pressure sensor connector A-12 by backpr...658
          STEP 13. Check connector A-12 at the manifold absolute pressure sensor and connector C-90 at PCM ...659
          STEP 14. Check for harness damage between manifold absolute pressure sensor connector A-12 (termi...660
          STEP 15. Check connector A-12 at manifold absolute pressure sensor for damage...660
          STEP 16. Check connector C-91 at PCM for damage...661
          STEP 17. Check for short circuit to ground and harness damage between manifold absolute pressure ...661
          STEP 18. Test the OBD-II drive cycle...662
      DTC P0108: Manifold Absolute Pressure Circuit High Input....662
        Logic Flow Chart....664
        DIAGNOSIS....665
          STEP 1. Using scan tool MB991958, check data list item 95: Manifold Absolute Pressure Sensor...665
          STEP 2. Measure the sensor output voltage at manifold absolute pressure sensor connector A-12 by ...666
          STEP 3. Check connector A-12 at the manifold absolute pressure sensor and connector C-91 at PCM f...667
          STEP 4. Using scan tool MB991958, check data list item 95: Manifold Absolute Pressure Sensor...668
          STEP 5. Measure the sensor supply voltage at manifold absolute pressure sensor connector A-12 by ...668
          STEP 6. Check connector C-90 at PCM for damage...669
          STEP 7. Measure the ground voltage at manifold absolute pressure sensor connector A-12 by backpro...669
          STEP 8. Check connector A-12 at the manifold absolute pressure sensor and connector C-90 at PCM f...670
          STEP 9. Check for open circuit between manifold absolute pressure sensor connector A-12 (terminal...671
          STEP 10. Check connector A-12 at manifold absolute pressure sensor for damage...671
          STEP 11. Check connector C-91 at PCM for damage...672
          STEP 12. Test the OBD-II drive cycle...672
      DTC P0111: Intake Air Temperature Circuit Range/Performance Problem....673
        Logic Flow Chart....675
        DIAGNOSIS....676
          STEP 1. Using scan tool MB991958, check data list item 13: Intake Air Temperature Sensor...676
          STEP 2. Check the intake air temperature sensor...677
          STEP 3. Check connector A-01 at the intake air temperature sensor for damage...677
          STEP 4. Measure the continuity at intake air temperature sensor harness side connector A-01...678
          STEP 5. Check connector C-90 at PCM for damage...678
          STEP 6. Check for harness damage between intake air temperature sensor connector A-01 (terminal N...679
          STEP 7. Check connector C-90 at PCM for damage...679
          STEP 8. Check for harness damage between intake air temperature sensor connector A-01 (terminal N...680
          STEP 9. Test the OBD-II drive cycle...680
      DTC P0112: Intake air temperature Circuit Low Input....681
        Logic Flow Chart....683
        DIAGNOSIS....684
          STEP 1. Using scan tool MB991958, check data list item 13: Intake Air Temperature Sensor...684
          STEP 2. Check connector A-01 at the intake air temperature sensor for damage...684
          STEP 3. Check the intake air temperature sensor...685
          STEP 4. Check for short circuit to ground between intake air temperature sensor connector A-01 (t...685
          STEP 5. Check connector C-90 at PCM for damage...686
          STEP 6. Test the OBD-II drive cycle...686
      DTC P0113: Intake air temperature Circuit High Input....687
        Logic Flow Chart....689
        DIAGNOSIS....690
          STEP 1. Using scan tool MB991958, check data list item 13: Intake Air Temperature Sensor...690
          STEP 2. Check connector A-01 at the intake air temperature sensor for damage...690
          STEP 3. Check the intake air temperature sensor...691
          STEP 4. Measure the sensor supply voltage at intake air temperature sensor harness side connector...691
          STEP 5. Measure the sensor supply voltage at PCM connector C-90 by backprobing...692
          STEP 6. Check connector C-90 at PCM for damage...692
          STEP 7. Check connector C-90 at PCM for damage...693
          STEP 8. Check for continuity at intake air temperature sensor harness side connector A-01...693
          STEP 9. Check connector C-90 at PCM for damage...694
          STEP 10. Check for open circuit between intake air temperature sensor connector A-01 (terminal No...694
          STEP 11. Test the OBD-II drive cycle...695
      DTC P0116: Engine Coolant Temperature Circuit Range/Performance Problem....695
        Logic Flow Chart....697
        DIAGNOSIS....698
          STEP 1. Using scan tool MB991958, check data list item 21: Engine Coolant Temperature Sensor...698
          STEP 2. Measure the sensor output voltage at engine coolant temperature sensor connector A-67 by ...699
          STEP 3. Check connector A-67 at the engine coolant temperature sensor for damage...699
          STEP 4. Using scan tool MB991958, check data list item 21: Engine Coolant Temperature Sensor...700
          STEP 5. Check connector A-67 at engine coolant temperature sensor for damage...700
          STEP 6. Measure the sensor supply voltage at engine coolant temperature sensor harness side conne...701
          STEP 7. Check connector C-90 at PCM for damage...701
          STEP 8. Check for continuity at engine coolant temperature sensor harness side connector A-67...702
          STEP 9. Check connector C-90 at PCM for damage...702
          STEP 10. Check for harness damage between engine coolant temperature sensor connector A-67 (termi...703
          STEP 11. Check the engine coolant temperature sensor...704
          STEP 12. Check connector C-90 at PCM for damage...704
          STEP 13. Check for harness damage between engine coolant temperature sensor connector A-67 (termi...705
          STEP 14. Test the OBD-II drive cycle...705
      DTC P0117: Engine Coolant Temperature Circuit Low Input....706
        Logic Flow Chart....708
        DIAGNOSIS....709
          STEP 1. Using scan tool MB991958, check data list item 21: Engine Coolant Temperature Sensor...709
          STEP 2. Check connector A-67 at the engine coolant temperature sensor for damage...709
          STEP 3. Check for short circuit to ground between engine coolant temperature sensor connector A-6...710
          STEP 4. Check connector C-90 at PCM for damage...710
          STEP 5. Check the engine coolant temperature sensor...711
          STEP 6. Test the OBD-II drive cycle...711
      DTC P0118: Engine Coolant Temperature Circuit High Input....712
        Logic Flow Chart....714
        DIAGNOSIS....715
          STEP 1. Using scan tool MB991958, check data list item 21: Engine Coolant Temperature Sensor...715
          STEP 2. Check connector A-67 at the engine coolant temperature sensor for damage...715
          STEP 3. Measure the sensor supply voltage at engine coolant temperature sensor harness side conne...716
          STEP 4. Measure the sensor supply voltage at PCM connector C-90 by backprobing...716
          STEP 5. Check connector C-90 at PCM for damage...717
          STEP 6. Check connector C-90 at PCM for damage...717
          STEP 7. Check for continuity at engine coolant temperature sensor harness side connector A-67...718
          STEP 8. Check connector C-90 at PCM for damage...718
          STEP 9. Check for open circuit between engine coolant temperature sensor connector A-67 (terminal...719
          STEP 10. Check the engine coolant temperature sensor...720
          STEP 11. Test the OBD-II drive cycle...720
      DTC P0121: Throttle Position Sensor Circuit Range/Performance Problem....721
        Logic Flow Chart....723
        Logic Flow Chart....724
        DIAGNOSIS....725
          STEP 1. Using scan tool MB991958, check data list item 14: Throttle Position Sensor...725
          STEP 2. Check connector A-41 at throttle position sensor for damage...725
          STEP3. Check the throttle position sensor...726
          STEP 4. Measure the sensor supply voltage at throttle position sensor harness side connector A-41...726
          STEP 5. Check connector C-90 at PCM for damage...727
          STEP 6. Check for harness damage between throttle position sensor connector A-41 (terminal No. 4)...727
          STEP 7. Check for continuity at throttle position sensor harness side connector A-41...728
          STEP 8. Check connector C-90 at PCM for damage...728
          STEP 9. Check for open circuit and harness damage between throttle position sensor connector A-41...729
          STEP 10. Check connector C-90, C-91 at PCM for damage...730
          STEP 11. Check for harness damage between throttle position sensor connector A-41 (terminal No. 3...730
          STEP 12. Check the incorrectly adjusted throttle position sensor...731
          STEP 13. Using scan tool MB991958, check data list item 14: Throttle Position Sensor...731
          STEP 14. Test the OBD-II drive cycle...731
      DTC P0122: Throttle Position Sensor Circuit Low Input....732
        Logic Flow Chart....734
        DIAGNOSIS....735
          STEP 1. Using scan tool MB991958, check data list item 14: Throttle Position Sensor...735
          STEP 2. Check connector A-41 at throttle position sensor for damage...735
          STEP 3. Measure the sensor supply voltage at throttle position sensor harness side connector A-41...736
          STEP 4. Check connector C-90 at PCM for damage...736
          STEP 5. Check for open circuit and short circuit to ground between throttle position sensor conne...737
          STEP 6. Check the throttle position sensor...738
          STEP 7. Check connector C-90, C-91 at PCM for damage...738
          STEP 8. Check for open circuit and short circuit to ground between throttle position sensor conne...739
          STEP 9. Using scan tool MB991958, check data list item 14: Throttle Position Sensor...740
          STEP 10. Test the OBD-II drive cycle...740
      DTC P0123: Throttle Position Sensor Circuit High Input....741
        Logic Flow Chart....743
        DIAGNOSIS....744
          STEP 1. Using scan tool MB991958, check data list item 14: Throttle Position Sensor...744
          STEP 2. Check connector A-41 at throttle position sensor for damage...744
          STEP 3. Check for continuity at throttle position sensor harness side connector A-41...745
          STEP 4. Check connector C-90 at PCM for damage...745
          STEP 5. Check for open circuit and harness damage between throttle position sensor connector A-41...746
          STEP 6. Check the throttle position sensor...747
          STEP 7. Using scan tool MB991958, check data list item 14: Throttle Position Sensor...747
          STEP 8. Test the OBD-II drive cycle...748
      DTC P0125: Insufficient Coolant Temperature for Closed Loop Fuel Control....748
        Logic Flow Chart....750
        Logic Flow Chart....751
        DIAGNOSIS....752
          STEP 1. Using scan tool MB991958, check data list item 21: Engine Coolant Temperature Sensor...752
          STEP 2. Measure the sensor output voltage at engine coolant temperature sensor connector A-67 by ...753
          STEP 3. Check connector A-67 at the engine coolant temperature sensor for damage...753
          STEP 4. Using scan tool MB991958, check data list item 21: Engine Coolant Temperature Sensor...754
          STEP 5. Check connector A-67 at engine coolant temperature sensor for damage...754
          STEP 6. Measure the sensor supply voltage at engine coolant temperature sensor harness side conne...755
          STEP 7. Check connector C-90 at PCM for damage...755
          STEP 8. Check for continuity at engine coolant temperature sensor harness side connector A-67...756
          STEP 9. Check connector C-90 at PCM for damage...756
          STEP 10. Check for harness damage between engine coolant temperature sensor connector A-67 (termi...757
          STEP 11. Check the engine coolant temperature sensor...758
          STEP 12. Check connector C-90 at PCM for damage...758
          STEP 13. Check for harness damage between engine coolant temperature sensor connector A-67 (termi...759
          STEP 14. Test the OBD-II drive cycle...759
GR00003400B-13A....760
  MULTIPORT FUEL INJECTION (MFI)....0
    MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS....0
      DTC P0128: Coolant Thermostat (Coolant Temperature Below Thermostat Regulating Temperature)....760
        Logic Flow Chart....760
        DIAGNOSIS....761
          STEP 1. Check the cooling system...761
      DTC P0130: Heated Oxygen Sensor Circuit (bank 1, sensor 1)....762
        Logic Flow Chart....765
        DIAGNOSIS....766
          STEP 1. Using scan tool MB991958, check data list item 39: Heated Oxygen Sensor Bank 1, Sensor 1 ...766
          STEP 2. Measure the sensor output voltage at right bank heated oxygen sensor (front) connector A-...767
          STEP 3. Check connector A-07 at right bank heated oxygen sensor (front) and connector C-91 at PCM...768
          STEP 4. Check for open circuit between right bank heated oxygen sensor (front) connector A-07 (te...769
          STEP 5. Using scan tool MB991958, check data list item 39: Heated Oxygen Sensor Bank 1, Sensor 1 ...770
          STEP 6. Check connector A-07 at right bank heated oxygen sensor (front) for damage...770
          STEP 7. Check for continuity at right bank heated oxygen sensor (front) harness side connector A-07...771
          STEP 8. Check connector C-90 at PCM for damage...771
          STEP 9. Check for open circuit between right bank heated oxygen sensor (front) connector A-07 (te...772
          STEP 10. Check the right bank heated oxygen sensor (front)...773
          STEP 11. Test the OBD-II drive cycle...774
      DTC P0131: Heated Oxygen Sensor Circuit Low Voltage (bank 1, sensor 1)....774
        Logic Flow Chart....777
        DIAGNOSIS....778
          STEP 1. Using scan tool MB991958, check data list item 39: Heated Oxygen Sensor Bank 1, Sensor 1 ...778
          STEP 2. Check the right bank heated oxygen sensor (front)...779
          STEP 3. Check connector A-07 at right bank heated oxygen sensor (front) and connector C-91 at PCM...780
          STEP 4. Check for short circuit to ground and harness damage between right bank heated oxygen sen...781
          STEP 5. Test the OBD-II drive cycle...781
      DTC P0132: Heated Oxygen Sensor Circuit High Voltage (bank 1, sensor 1)....782
        Logic Flow Chart....784
        DIAGNOSIS....785
          STEP 1. Check connector A-07 at right bank heated oxygen sensor (front) and connector C-91 at PCM...785
          STEP 2. Check for short circuit to power supply between right bank heated oxygen sensor (front) c...786
          STEP 3. Test the OBD-II drive cycle...786
      DTC P0133: Heated Oxygen Sensor Circuit Slow Response (bank 1 sensor 1)....787
        Logic Flow Chart....789
        DIAGNOSIS....790
          STEP 1. Using scan tool MB991958, check data list item 39: Heated Oxygen Sensor (front)...790
          STEP 2. Check the heated oxygen sensor (front)...791
          STEP 3. Check harness connector A-07 at heated oxygen sensor (front) and harness connector C-90, ...792
          STEP 4. Test the OBD-II drive cycle...792
      DTC P0134: Heated Oxygen Sensor Circuit No Activity Detected (bank 1, sensor 1)....793
        Logic Flow Chart....794
        DIAGNOSIS....795
          STEP 1. Using scan tool MB991958, check data list item 69: Heated Oxygen Sensor Bank 1, Sensor 2 ...795
          STEP 2. Check for exhaust leaks...796
          STEP 3. Check for intake system vacuum leaks...796
          STEP 4. Check connector A-07 at the right bank heated oxygen sensor (front) for damage...796
          STEP 5. Check the right bank heated oxygen sensor (front)...797
          STEP 6. Check connector A-04 at injector intermediate connector for damage...798
          STEP 7. Check the right bank injector resistance at intermediate connector A-04...798
          STEP 8. Check connector A-73, A-74, A-75 at right bank injector for damage...799
          STEP 9. Check the right bank injector...799
          STEP 10. Check connector C-90, C-91 at PCM for damage...800
          STEP 11. Check for harness damage between right bank heated oxygen sensor (front) connector A-07 ...801
          STEP 12. Check for harness damage between right bank injector connector and PCM connector...802
          STEP 13. Check the fuel pressure...802
          STEP 14. Test the OBD-II drive cycle...802
      DTC P0135: Heated Oxygen Sensor Heater Circuit (bank 1 sensor 1)....803
        Logic Flow Chart....805
        DIAGNOSIS....806
          STEP 1. Check connector A-07at the right bank heated oxygen sensor (front) for damage...806
          STEP 2. Check the right bank heated oxygen sensor (front)...807
          STEP 3. Measure the power supply voltage at right bank heated oxygen sensor (front) harness side ...808
          STEP 4. Check connector C-59 at the MFI relay for damage...808
          STEP 5. Measure the power supply voltage at PCM connector C-89 by backprobing...809
          STEP 6. Check connector C-89 at PCM for damage...809
          STEP 7. Check for open circuit or short circuit to ground between right bank heated oxygen sensor...810
          STEP 8. Check connector C-89 at PCM for damage...811
          STEP 9. Check for harness damage between MFI relay connector C-59 (terminal No. 1) and right bank...811
          STEP 10. Check for harness damage between right bank heated oxygen sensor (front) connector A-07 ...812
          STEP 11. Retest the system...813
          STEP 12. Test the OBD-II drive cycle...813
      DTC P0136: Heated Oxygen Sensor Circuit (bank 1 sensor 2)....814
        Logic Flow Chart....817
        DIAGNOSIS....818
          STEP 1. Using scan tool MB991958, check data list item 69: Heated Oxygen Sensor Bank 1, Sensor 2 ...818
          STEP 2. Measure the sensor output voltage at right bank heated oxygen sensor (rear) connector E-4...819
          STEP 3. Check connector E-47 at right bank heated oxygen sensor (rear) and connector C-91 at PCM ...820
          STEP 4. Check for open circuit between right bank heated oxygen sensor (rear) connector E-47 (ter...821
          STEP 5. Using scan tool MB991958, check data list item 69: Heated Oxygen Sensor Bank 1, Sensor 2 ...822
          STEP 6. Check connector E-47 at right bank heated oxygen sensor (rear) for damage...822
          STEP 7. Check for continuity at right bank heated oxygen sensor (rear) harness side connector E-47...823
          STEP 8. Check connector C-90 at PCM for damage...823
          STEP 9. Check for open circuit between right bank heated oxygen sensor (rear) connector E-47 (ter...824
          STEP 10. Check the right bank heated oxygen sensor (rear)...825
          STEP 11. Test the OBD-II drive cycle...826
      DTC P0137: Heated Oxygen Sensor Circuit Low Voltage (bank 1, sensor 2)....827
        Logic Flow Chart....830
        DIAGNOSIS....831
          STEP 1. Using scan tool MB991958, check data list item 69: Heated Oxygen Sensor Bank 1, Sensor 2 ...831
          STEP 2. Check the right bank heated oxygen sensor (rear)...832
          STEP 3. Check connector E-47 at right bank heated oxygen sensor (rear) and connector C-91 at PCM ...833
          STEP 4. Check for short circuit to ground between right bank heated oxygen sensor (rear) connecto...834
          STEP 5. Test the OBD-II drive cycle...835
      DTC P0138: Heated Oxygen Sensor Circuit High Voltage (bank 1 sensor 2)....836
        Logic Flow Chart....838
        DIAGNOSIS....839
          STEP 1. Check connector E-47 at right bank heated oxygen sensor (rear) and connector C-91 at PCM ...839
          STEP 2. Check for short circuit to ground and harness damage between right bank heated oxygen sen...840
          STEP 3. Test the OBD-II drive cycle...841
      DTC P0139: Heated Oxygen Sensor Circuit Slow Response (bank 1 sensor 2)....842
        Logic Flow Chart....844
        DIAGNOSIS....845
          STEP 1. Using scan tool MB991958, check data list item 69: Heated Oxygen Sensor Bank 1, Sensor 2 ...845
          STEP 2. Check the right bank heated oxygen sensor (rear)...846
          STEP 3. Check harness connector E-47 at right bank heated oxygen sensor (rear) and harness connec...847
          STEP 4. Test the OBD-II drive cycle...847
      DTC P0141: Heated Oxygen Sensor Heater Circuit (bank 1 sensor 2)....848
        Logic Flow Chart....850
        DIAGNOSIS....851
          STEP 1. Check connector E-47 at the right bank heated oxygen sensor (rear) for damage...851
          STEP 2. Check the right bank heated oxygen sensor (rear)...852
          STEP 3. Measure the power supply voltage at right bank heated oxygen sensor (rear) harness side c...853
          STEP 4. Check harness connector C-59 at the MFI relay for damage...853
          STEP 5. Measure the power supply voltage at PCM connector C-89 by backprobing...854
          STEP 6. Check connector C-89 at PCM for damage...854
          STEP 7. Check for open circuit or short circuit to ground between right bank heated oxygen sensor...855
          STEP 8. Check connector C-89 at PCM for damage...856
          STEP 9. Check for harness damage between MFI relay connector C-59 (terminal No. 1) and right bank...856
          STEP 10. Check for harness damage between right bank heated oxygen sensor (rear) connector E-47 (...857
          STEP 11. Retest the system...858
          STEP 12. Test the OBD- II drive cycle...858
      DTC P0150: Heated Oxygen Sensor Circuit (bank 2 sensor 1)....859
        Logic Flow Chart....862
        DIAGNOSIS....863
          STEP 1. Using scan tool MB991958, check data list item 11: Heated Oxygen Sensor Bank 2, Sensor 1 ...863
          STEP 2. Measure the sensor output voltage at left bank heated oxygen sensor (front) connector A-0...864
          STEP 3. Check connector A-09 at left bank heated oxygen sensor (front) and connector C-91 at PCM ...865
          STEP 4. Check for open circuit between left bank heated oxygen sensor (front) connector A-09 (ter...866
          STEP 5. Using scan tool MB991958, check data list item 11: Heated Oxygen Sensor Bank 2, Sensor 1 ...867
          STEP 6. Check connector A-09 at left bank heated oxygen sensor (front) for damage...867
          STEP 7. Check for continuity at left bank heated oxygen sensor (front) harness side connector A-09...868
          STEP 8. Check connector C-90 at PCM for damage...868
          STEP 9. Check for open circuit between left bank heated oxygen sensor (front) connector A-09 (ter...869
          STEP 10. Check the left bank heated oxygen sensor (front)...870
          STEP 11. Test the OBD-II drive cycle...871
      DTC P0151: Heated Oxygen Sensor Circuit Low Voltage (bank 2, sensor 1)....871
        Logic Flow Chart....874
        DIAGNOSIS....875
          STEP 1. Using scan tool MB991958, check data list item 11: Heated Oxygen Sensor Bank 2, Sensor 1 ...875
          STEP 2. Check the left bank heated oxygen sensor (front)...876
          STEP 3. Check connector A-09 at left bank heated oxygen sensor (front) and connector C-91 at PCM ...877
          STEP 4. Check for short circuit to ground and harness damage between left bank heated oxygen sens...878
          STEP 5. Test the OBD-II drive cycle...878
      DTC P0152: Heated Oxygen Sensor Circuit High Voltage (bank 2, sensor 1)....879
        Logic Flow Chart....881
        DIAGNOSIS....882
          STEP 1. Check connector A-09 at left bank heated oxygen sensor (front) and connector C-91 at PCM ...882
          STEP 2. Check for short circuit to power supply between left bank heated oxygen sensor (front) co...883
          STEP 3. Test the OBD-II drive cycle...883
      DTC P0153: Heated Oxygen Sensor Circuit Slow Response (bank 2 sensor 1)....884
        Logic Flow Chart....886
        DIAGNOSIS....887
          STEP 1. Using scan tool MB991958, check data list item 11: Heated Oxygen Sensor Bank 2, Sensor 1 ...887
          STEP 2. Check the left bank heated oxygen sensor (front)...888
          STEP 3. Check harness connector A-09 at left bank heated oxygen sensor (front) and harness connec...889
          STEP 4. Test the OBD-II drive cycle...890
      DTC P0154: Heated Oxygen Sensor Circuit No Activity Detected (bank 2, sensor 1)....890
        Logic Flow Chart....891
        DIAGNOSIS....892
          STEP 1. Using scan tool MB991958, check data list item 59: Heated Oxygen Sensor Bank 2, Sensor 2 ...892
          STEP 2. Check for exhaust leaks...893
          STEP 3. Check for intake system vacuum leaks...893
          STEP 4. Check connector A-09 at the left bank heated oxygen sensor (front) for damage...893
          STEP 5. Check the left bank heated oxygen sensor (front)...894
          STEP 6. Check connector A-04 at injector intermediate connector for damage...895
          STEP 7. Check the left bank injector resistance at intermediate connector A-04...895
          STEP 8. Check connector A-70, A-71, A-72 at left bank injector for damage...896
          STEP 9. Check the left bank injector...896
          STEP 10. Check connector C-90, C-91 at PCM for damage...897
          STEP 11. Check for harness damage between left bank heated oxygen sensor (front) connector A-09 (...898
          STEP 12. Check for harness damage between left bank injector connector and PCM connector...899
          STEP 13. Check the fuel pressure...899
          STEP 14. Test the OBD-II drive cycle...899
      DTC P0155: Heated Oxygen Sensor Heater Circuit (bank 2 sensor 1)....900
        Logic Flow Chart....902
        DIAGNOSIS....903
          STEP 1. Check connector A-09 at the left bank heated oxygen sensor (front) for damage...903
          STEP 2. Check the left bank heated oxygen sensor (front)...904
          STEP 3. Measure the power supply voltage at left bank heated oxygen sensor (front) harness side c...905
          STEP 4. Check connector C-59 at the MFI relay for damage...905
          STEP 5. Measure the power supply voltage at PCM connector C-89 by backprobing...906
          STEP 6. Check connector C-89 at PCM for damage...906
          STEP 7. Check for open circuit or short circuit to ground between left bank heated oxygen sensor ...907
          STEP 8. Check connector C-89 at PCM for damage...908
          STEP 9. Check for harness damage between MFI relay connector C-59 (terminal No. 1) and left bank ...908
          STEP 10. Check for harness damage between left bank heated oxygen sensor (front) connector A-09 (...909
          STEP 11. Retest the system...910
          STEP 12. Test the OBD-II drive cycle...910
      DTC P0156: Heated Oxygen Sensor Circuit (bank 2, sensor 2)....911
        Logic Flow Chart....914
        DIAGNOSIS....915
          STEP 1. Using scan tool MB991958, check data list item 59: Left Bank Heated Oxygen Sensor Bank 2,...915
          STEP 2. Measure the sensor output voltage at left bank heated oxygen sensor (rear) connector E-48...916
          STEP 3. Check harness connector E-48 at left bank heated oxygen sensor (rear) and harness connect...917
          STEP 4. Check for open circuit between left bank heated oxygen sensor (rear) connector E-48 (term...918
          STEP 5. Using scan tool MB991958, check data list item 59: Heated Oxygen Sensor Bank 2, Sensor 2 ...919
          STEP 6. Check harness connector E-48 at left bank heated oxygen sensor (rear) for damage...919
          STEP 7. Check for continuity at left bank heated oxygen sensor (rear) harness side connector E-48...920
          STEP 8. Check harness connector C-90 at PCM for damage...920
          STEP 9. Check for open circuit and harness damage between left bank heated oxygen sensor (rear) c...921
          STEP 10. Check the left bank heated oxygen sensor (rear)...922
          STEP 11. Test the OBD-II drive cycle...923
      DTC P0157: Heated Oxygen Sensor Circuit Low Voltage (bank 2, sensor 2)....924
        Logic Flow Chart....927
        DIAGNOSIS....928
          STEP 1. Using scan tool MB991958, check data list item 59: Heated Oxygen Sensor Bank 2, Sensor 2 ...928
          STEP 2. Check the left bank heated oxygen sensor (rear)...929
          STEP 3. Check connector E-48 at left bank heated oxygen sensor (rear) and connector C-91 at PCM f...930
          STEP 4. Check for short circuit to ground between left bank heated oxygen sensor (rear) connector...931
          STEP 5. Test the OBD-II drive cycle...932
      DTC P0158: Heated Oxygen Sensor Circuit High Voltage (bank 2, sensor 2)....933
        Logic Flow Chart....935
        DIAGNOSIS....936
          STEP 1. Check harness connector E-48 at left bank heated oxygen sensor (rear) and harness connect...936
          STEP 2. Check for short circuit to ground and harness damage between left bank heated oxygen sens...937
          STEP 3. Test the OBD-II drive cycle...938
      DTC P0159: Heated Oxygen Sensor Circuit Slow Response (bank 2, sensor 2)....939
        Logic Flow Chart....942
        DIAGNOSIS....943
          STEP 1. Using scan tool MB991958, check data list item 59: Heated Oxygen Sensor Bank 2, Sensor 2 ...943
          STEP 2. Check the left bank heated oxygen sensor (rear)...944
          STEP 3. Check harness connector E-48 at left bank heated oxygen sensor (rear) and harness connect...945
          STEP 4. Test the OBD-II drive cycle...945
      DTC P0161: Heated Oxygen Sensor Heater Circuit (bank 2 sensor 2)....946
        Logic Flow Chart....948
        DIAGNOSIS....949
          STEP 1. Check connector E-48 at the left bank heated oxygen sensor (rear) for damage...949
          STEP 2. Check the left bank heated oxygen sensor (rear)...950
          STEP 3. Measure the power supply voltage at left bank heated oxygen sensor (rear) harness side co...951
          STEP 4. Check connector C-59 at the MFI relay for damage...951
          STEP 5. Measure the power supply voltage at PCM connector C-89 by backprobing...952
          STEP 6. Check connector C-89 at PCM for damage...952
          STEP 7. Check for open circuit or short circuit to ground between left bank heated oxygen sensor ...953
          STEP 8. Check connector C-89 at PCM for damage...954
          STEP 9. Check for harness damage between MFI relay connector C-59 (terminal No. 1) and left bank ...954
          STEP 10. Check for harness damage between left bank heated oxygen sensor (rear) connector E-48 (t...955
          STEP 11. Retest the system...956
          STEP 12. Test the OBD-II drive cycle...956
      DTC P0171: System too Lean (bank 1)....956
        Logic Flow Chart....957
        DIAGNOSIS....959
          STEP 1. Check for exhaust leaks...959
          STEP 2. Check for intake system vacuum leaks...959
          STEP 3. Using scan tool MB991958, check data list item 12: Volume Airflow Sensor...959
          STEP 4. Using scan tool MB991958, check data list item 13: Intake Air Temperature Sensor...960
          STEP 5. Using scan tool MB991958, check data list item 21: Engine Coolant Temperature Sensor...960
          STEP 6. Using scan tool MB991958, check data list item 25: Barometric Pressure Sensor...961
          STEP 7. Check harness connector A-04 at injector intermediate connector for damage...961
          STEP 8. Check the right bank injector resistance at intermediate connector A-04...962
          STEP 9. Check harness connector A-73, A-74, A-75 at right bank injector for damage...962
          STEP 10. Check the right bank injector...963
          STEP 11. Check harness connector C-89 at PCM for damage...963
          STEP 12. Check for harness damage between right bank injector connector and PCM connector...964
          STEP 13. Check the fuel pressure...964
          STEP 14. Check for entry of foreign matter (water, kerosene, etc.) into fuel...964
          STEP 15. Replace the right bank injector...965
          STEP 16. Test the OBD-II drive cycle...965
      DTC P0172: System too Rich (bank 1)....965
        Logic Flow Chart....966
        DIAGNOSIS....967
          STEP 1. Using scan tool MB991958, check data list item 12: Volume Airflow Sensor...967
          STEP 2. Using scan tool MB991958, check data list item 13: Intake Air Temperature Sensor...968
          STEP 3. Using scan tool MB991958, check data list item 21: Engine Coolant Temperature Sensor...968
          STEP 4. Using scan tool MB991958, check data list item 25: Barometric Pressure Sensor...969
          STEP 5. Check harness connector A-04 at injector intermediate connector for damage...969
          STEP 6. Check the right bank injector resistance at intermediate connector A-04...970
          STEP 7. Check the right bank injector...970
          STEP 8. Check the fuel pressure...971
          STEP 9. Replace the right bank injector...971
          STEP 10. Test the OBD-II drive cycle...971
      DTC P0174: System too Lean (bank 2)....971
        Logic Flow Chart....972
        DIAGNOSIS....974
          STEP 1. Check for exhaust leaks...974
          STEP 2. Check for intake system vacuum leaks...974
          STEP 3. Using scan tool MB991958, check data list item 12: Volume Airflow Sensor...974
          STEP 4. Using scan tool MB991958, check data list item 13: Intake Air Temperature Sensor...975
          STEP 5. Using scan tool MB991958, check data list item 21: Engine Coolant Temperature Sensor...975
          STEP 6. Using scan tool MB991958, check data list item 25: Barometric Pressure Sensor...976
          STEP 7. Check harness connector A-04 at injector intermediate connector for damage...976
          STEP 8. Check the left bank injector resistance at intermediate connector A-04...977
          STEP 9. Check harness connector A-70, A-71, A-72 at left bank injector for damage...977
          STEP 10. Check the left bank injector...978
          STEP 11. Check harness connector C-89 at PCM for damage...978
          STEP 12. Check for harness damage between left bank injector connector and PCM connector...979
          STEP 13. Check the fuel pressure...979
          STEP 14. Check for entry of foreign matter (water, kerosene, etc.) into fuel...979
          STEP 15. Replace the left bank injector...979
          STEP 16. Test the OBD-II drive cycle...980
      DTC P0175: System too Rich (bank 1)....980
        Logic Flow Chart....981
        DIAGNOSIS....982
          STEP 1. Using scan tool MB991958, check data list item 12: Volume Airflow Sensor...982
          STEP 2. Using scan tool MB991958, check data list item 13: Intake Air Temperature Sensor...983
          STEP 3. Using scan tool MB991958, check data list item 21: Engine Coolant Temperature Sensor...983
          STEP 4. Using scan tool MB991958, check data list item 25: Barometric Pressure Sensor...984
          STEP 5. Check harness connector A-04 at injector intermediate connector for damage...984
          STEP 6. Check the left bank injector resistance at intermediate connector A-04...985
          STEP 7. Check the left bank injector...985
          STEP 8. Check the fuel pressure...986
          STEP 9. Replace the left bank injector...986
          STEP 10. Test the OBD-II drive cycle...986
      DTC P0181: Fuel Tank Temperature Sensor Circuit Range / Performance....987
        Logic Flow Chart....989
        DIAGNOSIS....990
          STEP 1. Using scan tool MB991958, check data list item 4A: Fuel Tank Temperature Sensor...990
          STEP 2. Measure the sensor output voltage at fuel tank temperature sensor connector E-30 by backp...991
          STEP 3. Check connector E-30 at the fuel tank temperature sensor for damage...991
          STEP 4. Using scan tool MB991958, check data list item 4A: Fuel Tank Temperature Sensor...992
          STEP 5. Check connector E-30 at fuel tank temperature sensor for damage...992
          STEP 6. Measure the sensor supply voltage at fuel tank temperature sensor harness side connector ...993
          STEP 7. Check connector C-90 at PCM for damage...993
          STEP 8. Check for continuity at fuel tank temperature sensor harness side connector E-30...994
          STEP 9. Check the fuel tank temperature sensor...994
          STEP 10. Check connector C-90 at PCM for damage...995
          STEP 11. Check for harness damage between fuel tank temperature sensor connector E-30 (terminal N...995
          STEP 12. Test the OBD-II drive cycle...996
      DTC P0182: Fuel Tank Temperature Sensor Circuit Low Input....997
        Logic Flow Chart....999
        DIAGNOSIS....999
          STEP 1. Using scan tool MB991958, check data list item 4A: Fuel Tank Temperature Sensor...1000
          STEP 2. Check the fuel tank temperature sensor...1000
          STEP 3. Check connector E-30 at the fuel tank temperature sensor and connector C-90 at PCM for da...1001
          STEP 4. Check for short circuit to ground between fuel tank temperature sensor connector E-30 (te...1002
          STEP 5. Test the OBD-II drive cycle...1002
      DTC P0183: Fuel Tank Temperature Sensor Circuit High Input....1003
        Logic Flow Chart....1005
        DIAGNOSIS....1006
          STEP 1. Using scan tool MB991958, check data list item 4A: Fuel Tank Temperature Sensor...1006
          STEP 2. Check connector E-30 at the fuel tank temperature sensor for damage...1006
          STEP 3. Check the fuel tank temperature sensor...1007
          STEP 4. Measure the sensor supply voltage at fuel tank temperature sensor harness side connector ...1007
          STEP 5. Measure the sensor supply voltage at PCM connector C-90 by backprobing...1008
          STEP 6. Check connector C-90 at PCM for damage...1008
          STEP 7. Check connector C-90 at PCM for damage...1009
          STEP 8. Check for continuity at fuel tank temperature sensor harness side connector E-30...1009
          STEP 9. Check connector C-90 at PCM for damage...1010
          STEP 10. Check for open circuit and harness damage between fuel tank temperature sensor connector...1010
          STEP 11. Test the OBD-II drive cycle...1011
      DTC P0201: Injector Circuit Malfunction - Cylinder 1, DTC P0202: Injector Circuit Malfunction - C...1012
        Logic Flow Chart....1014
        DIAGNOSIS....1015
          STEP 1. Using scan tool MB991958, check actuator test items 01, 02, 03, 04, 05, 06: Injectors...1015
          STEP 2. Check connector A-04 at injector intermediate connector for damage...1015
          STEP 3. Check the injector resistance at injector intermediate connector A-04...1016
          STEP 4. Check the connector at injector for damage...1016
          STEP 5. Check the injector...1017
          STEP 6. Measure the power supply voltage at injector intermediate connector A-04...1018
          STEP 7. Check connector C-59 at MFI relay for damage...1019
          STEP 8. Check for harness damage between MFI relay connector C-59 (terminal No. 1) and injector i...1019
          STEP 9. Check connector C-89 at PCM for damage...1020
          STEP 10. Check for open circuit and short circuit to ground and harness damage between injector i...1020
          STEP 11. Using the oscilloscope, check the injector...1021
          STEP 12. Test the OBD-II drive cycle...1022
GR00003400C-13A....1023
  MULTIPORT FUEL INJECTION (MFI)....0
    MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS....0
      DTC P0300: Random/Multiple Cylinder Misfire Detected....1023
        Logic Flow Chart....1024
        DIAGNOSIS....1025
          STEP 1. Using scan tool MB991958, check data list item 22: Crankshaft Position Sensor...1025
          STEP 2. Using scan tool MB991958, check data list item 81 <bank 1> and 83 <bank 2>: Long-Term Fue...1026
          STEP 3. Using scan tool MB991958, check data list item 82 <bank 1> and 84 <bank 2>: Short-Term Fu...1026
          STEP 4. Check the ignition coil spark...1027
          STEP 5. Check the spark plugs...1027
          STEP 6. Check the spark plug cable...1027
          STEP 7. Check the injector...1028
          STEP 8. Check connectors A-70, A-71, A-72, A-73, A-74, A-75 at injector and connector A-04 at inj...1028
          STEP 9. Check connector C-89 at PCM for damage...1029
          STEP 10. Check for harness damage between injector connector and PCM connector...1029
          STEP 11. Check the following items...1029
          STEP 12. Replace the injector...1030
          STEP 13. Test the OBD-II drive cycle...1030
      DTC P0301: Cylinder 1 Misfire Detected, DTC P0302: Cylinder 2 Misfire Detected, DTC P0303: Cylind...1030
        Logic Flow Chart....1031
        DIAGNOSIS....1032
          STEP 1. Check the spark plugs...1032
          STEP 2. Check the spark plug cable...1032
          STEP 3. Check the injector...1033
          STEP 4. Check connector at injector and injector intermediate connector for damage...1033
          STEP 5. Check connector C-89 at PCM for damage...1034
          STEP 6. Check for harness damage between injector connector and PCM connector...1034
          STEP 7. Check the compression...1034
          STEP 8. Replace the injector...1035
          STEP 9. Test the OBD-II drive cycle...1035
      DTC P0335: Crankshaft Position Sensor Circuit....1036
        Logic Flow Chart....1038
        Logic Flow Chart....1039
        DIAGNOSIS....1039
          STEP 1. Using scan tool MB991958, check data list item 22: Crankshaft Position Sensor...1040
          STEP 2. Using the oscilloscope, check the crankshaft position sensor...1040
          STEP 3. Check connector A-43 at the crankshaft position sensor for damage...1041
          STEP 4. Using scan tool MB991958, check data list item 22: Crankshaft Position Sensor...1041
          STEP 5. Check connector A-43 at the crankshaft position sensor for damage...1042
          STEP 6. Measure the sensor supply voltage at crankshaft position sensor harness side connector A-43...1043
          STEP 7. Measure the sensor supply voltage at PCM connector C-90 by backprobing...1044
          STEP 8. Check connector C-90 at PCM for damage...1044
          STEP 9. Check connector C-90 at PCM for damage...1045
          STEP 10. Check for short circuit to ground between crankshaft position sensor connector A-43 (ter...1046
          STEP 11. Measure the power supply voltage at crankshaft position sensor harness side connector A-43...1047
          STEP 12. Check connector C-59 at MFI relay for damage...1047
          STEP 13. Check for continuity at crankshaft position sensor harness side connector A-43...1048
          STEP 14. Check connector C-59 at the MFI relay for damage...1048
          STEP 15. Check connector C-90 at PCM for damage...1049
          STEP 16. Check for harness damage between MFI relay connector C-59 (terminal No. 1) and crankshaf...1049
          STEP 17. Check for harness damage between crankshaft position sensor connector A-43 (terminal No....1050
          STEP 18. Check for harness damage between crankshaft position sensor connector A-43 (terminal No....1051
          STEP 19. Check the crankshaft sensing blade...1051
          STEP 20. Test the OBD-II drive cycle...1051
      DTC P0340: Camshaft Position Sensor Circuit....1052
        Logic Flow Chart....1054
        Logic Flow Chart....1055
        DIAGNOSIS....1055
          STEP 1. Using the oscilloscope, check the camshaft position sensor...1056
          STEP 2. Check connector A-42 at camshaft position sensor for damage...1056
          STEP 3. Retest the system...1057
          STEP 4. Check connector A-42 at camshaft position sensor for damage...1057
          STEP 5. Measure the sensor supply voltage at camshaft position sensor connector A-42...1058
          STEP 6. Measure the sensor supply voltage at PCM connector C-90 by backprobing...1059
          STEP 7. Check connector C-90 at PCM for damage...1059
          STEP 8. Check connector C-90 at PCM for damage...1060
          STEP 9. Check for short circuit to ground between camshaft position sensor connector A-42 (termin...1061
          STEP 10. Measure the power supply voltage at camshaft position sensor connector A-42...1062
          STEP 11. Check connector C-59 at MFI relay for damage...1062
          STEP 12. Check for continuity at camshaft position sensor connector A-42...1063
          STEP 13. Check connector C-59 at the MFI relay for damage...1063
          STEP 14. Check connector C-90 at PCM for damage...1064
          STEP 15. Check for harness damage between MFI relay connector C-59 (terminal No. 1) and camshaft ...1064
          STEP 16. Check for harness damage between camshaft position sensor connector A-42 (terminal No. 2...1065
          STEP 17. Check the camshaft position sensing cylinder...1066
          STEP 18. Test the OBD-II drive cycle...1066
      DTC P0401: Exhaust Gas Recirculation Flow Insufficient Detected....1066
        Logic Flow Chart....1067
        DIAGNOSIS....1068
          STEP 1. Check the EGR system....1068
          STEP 2. Using scan tool MB991958, check data list item 95: Manifold Absolute Pressure Sensor...1068
          STEP 3. Test the OBD-II drive cycle...1069
      DTC P0403: Exhaust Gas Recirculation Control Circuit....1070
        Logic Flow Chart....1072
        DIAGNOSIS....1073
          STEP 1. Using scan tool MB991958, check actuator test item 10: EGR vacuum regulator solenoid valve...1073
          STEP 2. Check connector A-11 at the EGR vacuum regulator solenoid valve for damage...1073
          STEP 3 Check the EGR vacuum regulator solenoid valve...1074
          STEP 4. Measure the power supply voltage at EGR vacuum regulator solenoid valve harness side conn...1074
          STEP 5. Check connector C-59 at MFI relay for damage...1075
          STEP 6. Measure the power supply voltage at PCM connector C-89 by backprobing...1075
          STEP 7. Check connector C-89 at PCM for damage...1076
          STEP 8. Check for open circuit and short circuit to ground between EGR vacuum regulator solenoid ...1076
          STEP 9. Check connector C-89 at PCM for damage...1077
          STEP 10. Check for harness damage between MFI relay connector C-59 (terminal No. 1) and EGR vacuu...1077
          STEP 11. Check for harness damage between EGR vacuum regulator solenoid valve connector A-11 (ter...1078
          STEP 12. Test the OBD-II drive cycle...1078
      DTC P0421: Warm Up Catalyst Efficiency Below Threshold (bank 1)....1079
        Logic Flow Chart....1079
        DIAGNOSIS....1080
          STEP 1. Check for exhaust leaks...1080
          STEP 2. Using scan tool MB991958, check data list item 69: Heated Oxygen Sensor Bank 1, Sensor 2 ...1081
          STEP 3. Using scan tool MB991958, check data list item 39: Heated Oxygen Sensor Bank 1, Sensor 1 ...1081
          STEP 4. Using scan tool MB991958, check data list item 39: Heated Oxygen Sensor Bank 1, Sensor 1 ...1082
          STEP 5. Test the OBD-II drive cycle...1082
          STEP 6. Test the OBD-II drive cycle...1082
          STEP 7. Test the OBD-II drive cycle...1082
      DTC P0431: Warm Up Catalyst Efficiency Below Threshold (bank 2)....1083
        Logic Flow Chart....1084
        DIAGNOSIS....1085
          STEP 1. Check for exhaust leaks...1085
          STEP 2. Using scan tool MB991958, check data list item 59: Heated Oxygen Sensor Bank 2, Sensor 2 ...1085
          STEP 3. Using scan tool MB991958, check data list item 11: Heated Oxygen Sensor Bank 2, Sensor 1 ...1086
          STEP 4. Using scan tool MB991958, check data list item 11: Heated Oxygen Sensor Bank 2, Sensor 1 ...1086
          STEP 5. Test the OBD-II drive cycle...1087
          STEP 6. Test the OBD-II drive cycle...1087
          STEP 7. Test the OBD-II drive cycle...1087
      DTC P0441: Evaporative Emission Control System Incorrect Purge Flow....1088
        Logic Flow Chart....1089
        DIAGNOSIS....1089
          STEP1. Using scan tool MB991958, read the diagnostic trouble code (DTC)...1090
          STEP 2. Using scan tool MB991958, check data list item 73: Fuel Tank Differential Pressure Sensor...1090
          STEP 3. Using scan tool MB991958, check actuator test item 08: Evaporative Emission Purge Solenoid...1091
          STEP 4. Using scan tool MB991958, check actuator test item 29: Evaporative Emission Ventilation S...1091
          STEP 5 Test the OBD-II drive cycle...1092
      DTC P0442: Evaporative Emission Control System Leak Detected (Small Leak)....1092
        DIAGNOSIS....1096
          STEP 1. Using scan tool MB991958, check evaporative emission system monitor test...1096
          STEP 2. Check the evaporative emission purge solenoid valve using scan tool MB991958 (Actuator te...1097
          STEP 3. Check for leaks in the evaporator emission system hose A through hose C...1098
          STEP 4. Check the evaporative emission ventilation solenoid using scan tool MB991958. (Actuator t...1099
          STEP 5. Check for vacuum leak in evaporative emission system hose M...1100
          STEP 6. Check for vacuum leak in evaporative emission system hose D...1100
          STEP 7. Pressure test the evaporative emission system lines between hoses E to hose L and the fue...1101
          STEP 8. Check for vacuum leak in evaporative emission system hose E...1101
          STEP 9. Pressure test the evaporative emission system lines between hoses F and J...1102
          STEP 10. Check the check valve A...1102
          STEP 11. Check the check valve B...1102
          STEP 12. Check for leaks in the evaporative emission system hose K and L...1103
          STEP 13. Check for leaks in the fuel tank...1103
          STEP 14. Using scan tool MB991958, check evaporative emission system monitor test...1105
          STEP 15. Check the evaporative emission canister for leaks...1106
          STEP 16. Perform the OBD-II drive cycle...1106
      DTC P0443: Evaporative Emission Control System Purge Control Valve Circuit....1107
        Logic Flow Chart....1109
        DIAGNOSIS....1110
          STEP 1. Using scan tool MB991958, check actuator test item 08: Evaporative Emission Purge Solenoid...1110
          STEP 2. Check connector A-10 at the evaporative emission purge solenoid for damage...1110
          STEP 3. Check the evaporative emission purge solenoid...1111
          STEP 4. Measure the power supply voltage at evaporative emission purge solenoid harness side conn...1111
          STEP 5. Check connector C-59 at MFI relay for damage...1112
          STEP 6. Measure the power supply voltage at PCM connector C-89 by backprobing...1112
          STEP 7. Check connector C-89 at PCM for damage...1113
          STEP 8. Check for open circuit and short circuit to ground between evaporative emission purge sol...1113
          STEP 9. Check connector C-89 at PCM for damage...1114
          STEP 10. Check for harness damage between MFI relay connector C-59 (terminal No. 1) and evaporati...1114
          STEP 11. Check for harness damage between evaporative emission purge solenoid connector A-10 (ter...1115
          STEP 12. Test the OBD-II drive cycle...1115
      DTC P0446: Evaporative Emission Control System Vent Control Circuit....1116
        Logic Flow Chart....1118
        DIAGNOSIS....1119
          STEP 1. Using scan tool MB991958, check actuator test item 29: Evaporative Emission Ventilation S...1119
          STEP 2 Check connector E-63 at the evaporative emission ventilation solenoid for damage...1119
          STEP 3 Check the evaporative emission ventilation solenoid...1120
          STEP 4. Measure the power supply voltage at evaporative emission ventilation solenoid harness sid...1120
          STEP 5. Check connector C-59 at MFI relay for damage...1121
          STEP 6. Measure the power supply voltage at PCM connector C-89 by backprobing...1121
          STEP 7. Check connector C-89 at PCM for damage...1122
          STEP 8. Check for open circuit and short circuit to ground between evaporative emission ventilati...1122
          STEP 9. Check connector C-89 at PCM for damage...1123
          STEP 10. Check for harness damage between MFI relay connector C-59 (terminal No. 1) and evaporati...1123
          STEP 11. Check for harness damage between evaporative emission ventilation solenoid connector E-6...1124
          STEP 12. Test the OBD-II drive cycle...1124
      DTC P0451: Evaporative Emission Control System Pressure Sensor Range/Performance....1125
        DIAGNOSIS....1129
          STEP 1. Using scan tool MB991958, check data list item 73: Fuel Tank Differential Pressure Sensor...1130
          STEP 2. Measure the sensor output voltage at fuel tank differential pressure sensor connector E- 28...1131
          STEP 3. Measure the 5-volt supply circuit voltage at fuel tank differential pressure sensor conne...1132
          STEP 4. Check the ground circuit voltage at fuel tank differential pressure sensor connector E-28...1132
          STEP 5. Check connectors E-44, C-16, C-71 at intermediate connector and C-90 at PCM and E-28 at f...1133
          STEP 6. Check the harness wire for open circuit between PCM connector C-90 terminal 57 and fuel t...1135
          STEP 7. Measure the output circuit voltage at PCM connector C-91 by backprobing...1136
          STEP 8. Check connectors C-91 at PCM and E-28 at fuel tank differential pressure sensor for loose...1137
          STEP 9. Check connectors E-44, C-16, at intermediate connector and C-91 at PCM and E-28 at fuel t...1138
          STEP 10. Measure the 5-volt reference signal at PCM connector C-40 by backprobing...1139
          STEP 11. Check connectors E-44, C-16, at intermediate connector and C-90 at PCM and E-28 at fuel ...1140
          STEP 12. Measure the fuel tank differential pressure sensor ground voltage at PCM connector C-90 ...1141
          STEP 13. Check connectors E-44, C-16, C-71 at intermediate connector and C-90 at PCM and E-28 at ...1142
          STEP 14. Check connector C-90 at PCM for loose, corroded or damaged terminals, for terminals push...1144
          STEP 15. Using scan tool MB991958, check data list item 73: Fuel Tank Differential Pressure Sensor...1145
          STEP 16. Perform the OBD-II drive cycle...1146
      DTC P0452: Evaporative Emission Control System Pressure Sensor Low Input....1146
        DIAGNOSIS....1150
          STEP 1. Using scan tool MB991958, check data list item 73: Fuel Tank Differential Pressure Sensor...1151
          STEP 2. Measure the sensor output voltage at fuel tank differential pressure sensor connector E- 28...1152
          STEP 3. Measure the 5-volt supply circuit voltage at fuel tank differential pressure sensor conne...1153
          STEP 4. Measure the ground circuit voltage at fuel tank differential pressure sensor connector E-28...1153
          STEP 5. Check connectors E-44, C-16, C-71 at intermediate connector and C-90 at PCM and E-28 at f...1154
          STEP 6. Check the harness wire for open circuit between PCM connector C-90 terminal 57 and fuel t...1156
          STEP 7. Measure the output circuit voltage at PCM connector C-91 by backprobing...1157
          STEP 8. Check connectors C-91 at PCM and E-28 at fuel tank differential pressure sensor for loose...1158
          STEP 9. Check connectors E-44, C-16, at intermediate connector and C-91 at PCM and E-28 at fuel t...1159
          STEP 10. Measure the 5-volt reference signal at PCM connector C-90 by backprobing...1160
          STEP 11. Check connectors E-44, C-16, at intermediate connector and C-90 at PCM and E-28 at fuel ...1161
          STEP 12. Measure the ground voltage at intermediate connector C-90 by backprobing...1162
          STEP 13. Check connectors E-44, C-16, C-71 at intermediate connector and C-90 at PCM and E-28 at ...1163
          STEP 14. Check connector C-90 at PCM for loose, corroded or damaged terminals or terminals pushed...1165
          STEP 15. Using scan tool MB991958, check data list item 73: Fuel Tank Differential Pressure Sensor...1166
          STEP 16. Perform the OBD-II drive cycle...1167
      DTC P0453: Evaporative Emission Control System Pressure Sensor High Input....1167
        DIAGNOSIS....1171
          STEP 1. Using scan tool MB991958, check data list item 73: Fuel Tank Differential Pressure Sensor...1172
          STEP 2. Measure the sensor output voltage at fuel tank differential pressure sensor connector E- 28...1173
          STEP 3. Measure the 5-volt supply circuit voltage at fuel tank differential pressure sensor conne...1174
          STEP 4. Measure the ground circuit voltage at fuel tank differential pressure sensor connector E-28...1174
          STEP 5. Check connectors E-44, C-16, C-71 at intermediate connector and C-90 at PCM and E-28 at f...1175
          STEP 6. Check the harness wire for open circuit between PCM connector C-90 terminal 57 and fuel t...1177
          STEP 7. Measure the output circuit voltage at PCM connector C-91 by backprobing...1178
          STEP 8. Check connectors C-91 at PCM and E-28 at fuel tank differential pressure sensor for loose...1179
          STEP 9. Check connectors E-44, C-16, at intermediate connector and C-91 at PCM and E-28 at fuel t...1180
          STEP 10. Measure the 5-volt reference signal at PCM connector C-90 by backprobing...1181
          STEP 11. Check connectors E-44, C-16, at intermediate connector and C-90 at PCM and E-28 at fuel ...1182
          STEP 12. Measure the ground voltage at intermediate connector C-90 by backprobing...1183
          STEP 13. Check connectors E-44, C-16, C-71 at intermediate connector and C-90 at PCM and E-28 at ...1184
          STEP 14. Check connector C-90 at PCM for loose, corroded or damaged terminals, or terminals pushe...1186
          STEP 15. Using scan tool MB991958, check data list item 73: Fuel Tank Differential Pressure Sensor...1187
          STEP 16. Perform the OBD-II drive cycle...1188
      DTC P0455: Evaporative Emission Control System Leak Detected (Gross Leak)....1189
        DIAGNOSIS....1193
          STEP 1. Using scan tool MB991958, check evaporative emission system monitor test...1193
          STEP 2. Check the evaporative emission purge solenoid valve using scan tool MB991958 (Actuator te...1194
          STEP 3. Check for leaks and clogging in the evaporative emission system hoses A through C...1195
          STEP 4. Check the evaporative emission ventilation solenoid using scan tool MB991958. (Actuator t...1196
          STEP 5. Check for leaks the evaporator line hose M...1197
          STEP 6. Check for vacuum leaks and clogging in evaporator line hose D...1197
          STEP 7. Pressure test the evaporative emission system lines between hose E, L and the fuel tank...1198
          STEP 8. Check for vacuum leaks in the evaporative emission system hose E...1198
          STEP 9. Pressure test the evaporative emission system from hoses F through J...1199
          STEP 10. Check the check valve A...1199
          STEP 11. Check the check valve B...1199
          STEP 12. Check for leaks in the evaporative emission system hoses K through L...1200
          STEP 13. Check for leak in the fuel tank...1200
          STEP 14. Using scan tool MB991958, check evaporative emission system monitor test...1201
          STEP 15. Pressure test for clogging in evaporative emission system line between hose E and L...1202
          STEP 16. Check for clogging in the evaporative emission system line hose E...1202
          STEP 17. Check for clogging in the evaporator line from hoses F...1203
          STEP 18. Check the evaporative emission canister for leaks and clogging...1203
          STEP 19. Perform the OBD-II drive cycle...1203
      DTC P0456: Evaporative Emission Control System Leak Detected (Very Small Leak)....1204
        DIAGNOSIS....1208
          STEP 1. Using scan tool MB991958, check evaporative emission system monitor test...1208
          STEP 2. Check the evaporative emission purge solenoid valve using scan tool MB991958 (Actuator te...1209
          STEP 3. Check for leaks in the evaporative emission system line between hose A through C...1210
          STEP 4. Check the evaporative emission ventilation solenoid using scan tool MB991958. (Actuator t...1211
          STEP 5. Check for leaks in the evaporative emission system hose M...1212
          STEP 6. Check for vacuum leaks in the evaporative emission system hose D...1212
          STEP 7. Pressure test the evaporative emission system lines from hose E, L and the fuel tank...1213
          STEP 8. Check vacuum for leaks in the evaporative emission system hose E...1213
          STEP 9. Pressure test the leaks in the evaporative emission system from hoses H through O...1214
          STEP 10. Check the check valve A...1214
          STEP 11. Check the check valve B...1214
          STEP 12. Check for leaks in the evaporative emission system line from hose K through L...1215
          STEP 13. Check for leak in the fuel tank...1215
          STEP 14. Using scan tool MB991958, check evaporative emission system monitor test...1216
          STEP 15. Check the evaporative emission canister for leaks and clogging...1217
          STEP 16. Perform the OBD-II drive cycle...1217
      DTC P0461: Fuel Level Sensor Circuit Range/Performance....1218
        Logic Flow Chart....1220
        DIAGNOSIS....1221
          STEP 1. Check fuel gauge...1221
          STEP 2. Check for short circuit to ground between fuel level sensor connector E-30 (terminal No. ...1221
          STEP 3. Check connector C-90 at PCM for damage...1222
          STEP 4. Check for open circuit or harness damage between fuel gauge unit connector E-30 (terminal...1222
          STEP 5. Retest the system...1223
          STEP 6. Test the OBD-II drive cycle...1223
      DTC P0506: Idle Control System RPM Lower Than Expected....1224
        Logic Flow Chart....1226
        DIAGNOSIS....1227
          STEP 1. Using scan tool MB991958, read the diagnostic trouble code (DTC)...1227
          STEP 2. Check the throttle body (throttle valve area)....1227
          STEP 3. Check connector A-40 at idle air control motor for damage...1228
          STEP 4. Measure the idle air control motor coil resistance...1228
          STEP 5. Measure the power supply voltage at idle air control motor harness side connector A-40...1229
          STEP 6. Check connector C-59 at MFI relay for damage...1229
          STEP 7. Measure the power supply voltage at PCM connector C-89 by backprobing....1230
          STEP 8. Check connector C-89 at PCM for damage...1230
          STEP 9. Check for open circuit and short circuit to ground between idle air control motor connect...1231
          STEP 10. Check connector C-89 at PCM for damage...1231
          STEP 11. Check the idle air control motor operation using special tool MB991709...1232
          STEP 12. Check for harness damage between MFI relay connector C-59 (terminal No. 1) and idle air ...1233
          STEP 13. Check for harness damage between idle air control motor connector A-40 and PCM connector...1233
          STEP 14. Test the OBD-II drive cycle...1234
      DTC P0507: Idle Control System RPM Higher than Expected....1235
        Logic Flow Chart....1237
        DIAGNOSIS....1238
          STEP 1. Using scan tool MB991958, read the diagnostic trouble code (DTC)...1238
          STEP 2. Check for intake system vacuum leaks...1238
          STEP 3. Check connector A-40 at idle air control motor for damage...1238
          STEP 4. Check the idle air control motor coil resistance...1239
          STEP 5. Measure the power supply voltage at idle air control motor harness side connector A-40...1240
          STEP 6. Check connector C-59 at MFI relay for damage...1240
          STEP 7. Measure the power supply voltage at PCM connector C-89 by backprobing....1241
          STEP 8. Check connector C-89 at PCM for damage...1241
          STEP 9. Check for open circuit and short circuit to ground between idle air control motor connect...1242
          STEP 10. Check connector C-89 at PCM for damage...1242
          STEP 11. Check the idle air control motor operation using special tool MB991709...1243
          STEP 12. Check for harness damage between MFI relay connector C-59 (terminal No. 1) and idle air ...1244
          STEP 13. Check for harness damage between idle air control motor connector A-40 and PCM connector...1244
          STEP 14. Test the OBD-II drive cycle...1245
      DTC P0513: Immobilizer Malfunction....1245
        DIAGNOSIS....1246
          STEP 1. Using scan tool MB991958, read the immobilizer system diagnostic trouble code (DTC)...1246
      DTC P0551: Power Steering Pressure Sensor Circuit Range/Performance....1247
        Logic Flow Chart....1248
        DIAGNOSIS....1249
          STEP 1. Using scan tool MB991958, check data list item 27: Power Steering Pressure Switch...1249
          STEP 2. Measure the power supply voltage at power steering pressure switch connector A-76 by back...1250
          STEP 3. Check connector A-76 at power steering pressure switch for damage...1250
          STEP 4. Using scan tool MB991958, check data list item 27: Power Steering Pressure Switch...1251
          STEP 5. Check connector A-76 at power steering pressure switch for damage...1251
          STEP 6. Measure the power supply voltage at power steering pressure switch harness side connector...1252
          STEP 7. Measure the power supply voltage at PCM connector C-90 by backprobing...1252
          STEP 8. Check connector C-90 at PCM for damage...1253
          STEP 9. Check connector C-90 at PCM for damage...1253
          STEP 10. Check for short circuit to ground between power steering pressure switch connector A-76 ...1254
          STEP 11. Replace the power steering pressure switch...1254
          STEP 12. Check connector C-90 at PCM for damage...1255
          STEP 13. Check for harness damage between power steering pressure switch connector A-76 (terminal...1255
          STEP 14. Using scan tool MB991958, check data list item 27: Power Steering Pressure Switch...1256
      DTC P0554: Power Steering Pressure Sensor Circuit Intermittent....1257
        DIAGNOSIS....1259
          STEP 1. Using scan tool MB991958, check data list item 27: Power Steering Pressure Switch...1259
          STEP 2. Check the power steering fluid level...1259
          STEP 3. Check the power steering pressure switch...1259
          STEP 4. Check the oil pump pressure ...1260
          STEP 5. Check connector A-76 at the power steering pressure switch and connector C-90 at PCM for ...1260
          STEP 6. Check for harness damage between power steering pressure switch connector A-76 (terminal ...1261
          STEP 7. Using scan tool MB991958, check data list item 27: Power Steering Pressure Switch...1262
      DTC P1603: Battery Backup Line Malfunction....1263
        DIAGNOSIS....1264
          STEP 1. Using scan tool MB991958, read the diagnostic trouble code (DTC)...1265
          STEP 2. Measure the backup power supply voltage at PCM connector C-90 by backprobing...1265
          STEP 3. Measure the backup power supply voltage at PCM harness side connector C-90...1266
          STEP 4. Check connector C-90 at PCM for damage...1266
          STEP 5. Check connector C-90 at PCM for damage...1267
          STEP 6. Using scan tool MB991958, read the diagnostic trouble code (DTC)...1267
      DTC P2227: Barometric Pressure Circuit Range/Performance Problem....1268
        Logic Flow Chart....1270
        DIAGNOSIS....1271
          STEP 1. Using scan tool MB991958, check data list item 25: Barometric Pressure Sensor...1271
          STEP 2. Replace the airflow sensor...1271
          STEP 3. Check connector A-01 at the barometric pressure sensor and connector C-90 at PCM for damage...1272
          STEP 4. Check for harness damage between barometric pressure sensor connector A-01 (terminal No. ...1273
          STEP 5. Check for harness damage between barometric pressure sensor connector A-01 (terminal No. ...1274
          STEP 6. Check for harness damage between barometric pressure sensor connector A-01 (terminal No. ...1275
          STEP 7. Test the OBD-II drive cycle...1275
      DTC P2228: Barometric Pressure Circuit Low Input....1276
        Logic Flow Chart....1278
        DIAGNOSIS....1279
          STEP 1. Using scan tool MB991958, check data list item 25: Barometric Pressure Sensor...1279
          STEP 2. Measure the sensor output voltage at barometric pressure sensor connector A-01 by backpro...1280
          STEP 3. Measure the sensor output voltage at PCM connector C-90 by backprobing...1281
          STEP 4. Check connector A-01 at the barometric pressure sensor and connector C-90 at PCM for damage...1282
          STEP 5. Using scan tool MB991958, check data list item 25: Barometric Pressure Sensor...1282
          STEP 6. Check connector A-01 at the barometric pressure sensor and connector C-90 at PCM for damage...1283
          STEP 7. Measure the sensor supply voltage at barometric pressure sensor connector A-01 by backpro...1283
          STEP 8. Measure the sensor supply voltage at PCM connector C-90 by backprobing...1284
          STEP 9. Check connector A-01 at the barometric pressure sensor and connector C-90 at PCM for damage...1285
          STEP 10. Check connector A-01 at the barometric pressure sensor and connector C-90 at PCM for dam...1286
          STEP 11. Check for short circuit to ground between barometric pressure sensor connector A-01 (ter...1287
          STEP 12. Measure the ground voltage at barometric pressure sensor connector A-01 by backprobing...1287
          STEP 13. Check connector A-01 at the barometric pressure sensor and connector C-90 at PCM for dam...1288
          STEP 14. Check for harness damage between barometric pressure sensor connector A-01 (terminal No....1289
          STEP 15. Check connector A-01 at barometric pressure sensor for damage...1289
          STEP 16. Check connector C-90 at PCM for damage...1290
          STEP 17. Check for short circuit to ground and harness damage between barometric pressure sensor ...1290
          STEP 18. Test the OBD-II drive cycle...1291
      DTC P2229: Barometric Pressure Circuit High Input....1291
        Logic Flow Chart....1293
        DIAGNOSIS....1293
          STEP 1. Using scan tool MB991958, check data list item 25: Barometric Pressure Sensor...1294
          STEP 2. Measure the sensor output voltage at barometric pressure sensor connector A-01 by backpro...1294
          STEP 3. Check connector A-01 at the barometric pressure sensor and connector C-90 at PCM for damage...1295
          STEP 4. Using scan tool MB991958, check data list item 25: Barometric Pressure Sensor...1295
          STEP 5. Measure the sensor supply voltage at barometric pressure sensor connector A-01 by backpro...1296
          STEP 6. Check connector C-90 at PCM for damage...1296
          STEP 7. Measure the ground voltage at barometric pressure sensor connector A-01 by backprobing...1297
          STEP 8. Check connector A-01 at the barometric pressure sensor and connector C-90 at PCM for damage...1297
          STEP 9. Check for open circuit between barometric pressure sensor connector A-01 (terminal No. 5)...1298
          STEP 10. Check connector A-01 at barometric pressure sensor for damage...1298
          STEP 11. Check connector C-90 at PCM for damage...1299
          STEP 12. Test the OBD-II drive cycle...1299
GR00003400D-13A....1300
  MULTIPORT FUEL INJECTION (MFI)....0
    MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS....0
      SYMPTOM PROCEDURES....1300
      INSPECTION PROCEDURE 1: Communication with Scan Tool Is Not Possible. (Comunication with All Syst...1300
        DIAGNOSIS....1301
          STEP 1. Measure the power supply voltage at data link connector C-69...1301
          STEP 2. Check for continuity at data link connector C-69...1302
      INSPECTION PROCEDURE 2: Scan Tool Communication with PCM Is Not Possible...1303
        DIAGNOSIS....1304
          STEP 1. Check harness connector C-91 at PCM for damage...1304
          STEP 2. Check for open circuit, short circuit to ground and harness damage between data link conn...1305
          STEP 3. Check for open circuit, short circuit to ground and harness damage between data link conn...1306
      INSPECTION PROCEDURE 3: The Malfunction Indicator Lamp (SERVICE ENGINE SOON or Check Engine Lamp)...1307
        DIAGNOSIS....1309
          STEP 1. Using scan tool MB991958, check data list item 16: Power Supply Voltage...1309
          STEP 2. Check the burned-out bulb...1309
          STEP 3. Check harness connector C-04 at the combination meter for damage...1309
          STEP 4. Measure the power supply voltage at combination meter harness side connector C-04...1310
          STEP 5. Check harness connector C-89 at the PCM for damage...1310
          STEP 6. Measure the power supply voltage at PCM connector C-89...1311
      INSPECTION PROCEDURE 4: The Malfunction Indicator Lamp (SERVICE ENGINE SOON or Check Engine Lamp)...1312
        DIAGNOSIS....1313
          STEP 1. Using scan tool MB991958, read the diagnostic trouble code (DTC)...1314
          STEP 2. Check for continuity at combination meter harness side connector C-04...1314
      INSPECTION PROCEDURE 5: Cranks, Won't Start....1315
        DIAGNOSIS....1315
          STEP 1. Measure the battery positive voltage...1315
          STEP 2. Check the timing belt for breaks...1315
          STEP 3 Using scan tool MB991958, check data list...1316
          STEP 4. Using scan tool MB991958, check actuator test...1316
          STEP 5. Check the ignition system...1317
          STEP 6. Check the ignition timing...1317
          STEP 7. Measure the injector resistance at injector intermediate connector A-04...1318
          STEP 8. Check the injector...1319
          STEP 9. Check harness connector A-70 or A-71 or A-72 or A-73 or A-74 or A-75 at injector for damage...1319
          STEP 10. Check harness connector A-04 at injector intermediate connector for damage...1319
          STEP 11. Check harness connector C-89 at PCM for damage...1320
          STEP 12. Check for harness damage between injector intermediate connector A-04 and PCM connector ...1320
      INSPECTION PROCEDURE 6: Fires Up and Dies...1321
        DIAGNOSIS....1321
          STEP 1. Measure the battery positive voltage...1321
          STEP 2. Using scan tool MB991958, read the diagnostic trouble code (DTC)...1321
          STEP 3. Using scan tool MB991958, check actuator test...1322
          STEP 4. Using scan tool MB991958, check data list...1322
          STEP 5. Check the engine start-ability...1323
          STEP 6. Check the idle air control (IAC) motor operation sound...1323
          STEP 7. Check the ignition timing...1323
          STEP 8. Measure the right bank injector resistance at injector intermediate connector A-04...1324
          STEP 9. Check the injector...1325
          STEP 10. Check harness connector A-70 or A-71 or A-72 or A-73 or A-74 or A-75 at injector for dam...1325
          STEP 11. Check harness connector A-04 at injector intermediate connector for damage...1325
          STEP 12. Check harness connector C-89 at PCM for damage...1326
          STEP 13. Check for harness damage between injector connector and PCM connector...1326
      INSPECTION PROCEDURE 7: Hard Starting....1327
        DIAGNOSIS....1327
          STEP 1. Measure the battery positive voltage...1327
          STEP 2. Using scan tool MB991958, read the diagnostic trouble code (DTC)...1327
          STEP 3. Using scan tool MB991958, check actuator test...1328
          STEP 4. Using scan tool MB991958, check data list...1328
          STEP 5. Check the ignition timing...1329
          STEP 6. Measure the right bank injector resistance at injector intermediate connector A-04...1329
          STEP 7. Check the injector...1330
          STEP 8. Check harness connectors A-70, A-71, A-72, A-73, A-74 or A-75 at injector for damage...1330
          STEP 9. Check harness connector A-04 at the injector intermediate connector for damage...1330
          STEP 10. Check the harness connector C-89 at the PCM for damage...1331
          STEP 11. C Check for harness damage between injector intermediate connector A-04 and PCM connecto...1331
      INSPECTION PROCEDURE 8: Unstable Idle (Rough Idle, Hunting)...1332
        DIAGNOSIS....1332
          STEP 1. Check if the battery terminal is disconnected...1332
          STEP 2. Using scan tool MB991958, read the diagnostic trouble code (DTC)...1332
          STEP 3. Check the engine idling state...1333
          STEP 4. Check the following items...1333
          STEP 5. Check the idle air control (IAC) motor operation sound...1333
          STEP 6. Using scan tool MB991958, check actuator test items 01, 02, 03, 04, 05, 06: Injector...1334
          STEP 7. Using scan tool MB991958, check data list...1334
          STEP 8. Using scan tool MB991958, check actuator test...1335
          STEP 9. Using scan tool MB991958, check data list...1335
          STEP 10. Using scan tool MB991958, check data list...1336
          STEP 11. Check the fuel pressure...1336
          STEP 12. Check the ignition timing...1337
      INSPECTION PROCEDURE 9: Idle speed is high (improper idle speed)...1337
        DIAGNOSIS....1337
          STEP 1. Using scan tool MB991958, read the diagnostic trouble code (DTC)...1338
          STEP 2. Check the idle air control (IAC) motor operation sound...1338
          STEP 3. Using scan tool MB991958, check data list...1339
          STEP 4. Adjust the basic idle speed...1339
      INSPECTION PROCEDURE 10: Idle Speed Is Low (Improper Idle Speed)...1339
        DIAGNOSIS....1339
          STEP 1. Using scan tool MB991958, read the diagnostic trouble code (DTC)...1340
          STEP 2. Check the idle air control (IAC) motor operation sound...1340
          STEP 3. Using scan tool MB991958, check data list...1341
          STEP 4. Adjust the basic idle speed...1341
      INSPECTION PROCEDURE 11: When the engine is cold, it stalls at idle (die out)...1341
        DIAGNOSIS....1341
          STEP 1. Check if the battery terminal is disconnected...1342
          STEP 2. Using scan tool MB991958, read the diagnostic trouble code (DTC)...1342
          STEP 3. Checking by operating the accelerator pedal...1342
          STEP 4. Check the engine idling...1342
          STEP 5. Check the idle air control (IAC) motor operation sound...1343
          STEP 6. Using scan tool MB991958, check actuator test items 01, 02, 03, 04, 05, 06: Injector...1343
          STEP 7. Using scan tool MB991958, check data list...1344
          STEP 8. Check the fuel pressure...1344
          STEP 9. Check the ignition timing...1344
      INSPECTION PROCEDURE 12: When the Engine Is Hot, It Stalls at Idle (Die Out)...1345
        DIAGNOSIS....1345
          STEP 1. Check if the battery terminal is disconnected...1345
          STEP 2. Using scan tool MB991958, read the diagnostic trouble code (DTC)...1345
          STEP 3. Check the idle air control (IAC) motor operation sound...1346
          STEP 4. Using scan tool MB991958, check actuator test items 01, 02, 03, 04, 05, 06: Injector...1346
          STEP 5. Checking by operating the accelerator pedal...1347
          STEP 6. Engine stall reproduction test...1347
          STEP 7. Using scan tool MB991958, check data list...1347
          STEP 8. Using scan tool MB991958, check actuator test...1348
          STEP 9. Using scan tool MB991958, check data list...1348
          STEP 10. Check the fuel pressure...1349
          STEP 11. Using scan tool MB991958, check data list...1349
          STEP 12. Check the ignition timing...1349
      INSPECTION PROCEDURE 13: The Engine Stalls when Accelerating (Pass Out)...1350
        DIAGNOSIS....1350
          STEP 1. Using scan tool MB991958, read the diagnostic trouble code (DTC)...1350
          STEP 2. Using scan tool MB991958, check actuator test...1351
      INSPECTION PROCEDURE 14: The engine stalls when decelerating...1351
        DIAGNOSIS....1351
          STEP 1. Check if the battery terminal is disconnected....1351
          STEP 2. Using scan tool MB991958, read the diagnostic trouble code (DTC)...1352
          STEP 3. Using scan tool MB991958, check data list...1352
          STEP 4. Using scan tool MB991958, check actuator test...1353
          STEP 5. Using scan tool MB991958, check data list item 45: Idle Air Control Position...1353
      INSPECTION PROCEDURE 15: Hesitation, sag or stumble...1354
        DIAGNOSIS....1354
          STEP 1. Using scan tool MB991958, read the diagnostic trouble code (DTC)...1354
          STEP 2. Using scan tool MB991958, check actuator test items 01, 02, 03, 04, 05, 06: Injector...1355
          STEP 3. Check the ignition timing...1355
          STEP 4. Using scan tool MB991958, check data list and actuator test...1356
          STEP 5. Using scan tool MB991958, check actuator test...1356
          STEP 6. Using scan tool MB991958, check data list...1357
          STEP 7. Check the fuel pressure...1357
          STEP 8. Check the fuel pressure...1358
      INSPECTION PROCEDURE 16: Acceleration shock...1359
        DIAGNOSIS....1359
          STEP 1. Using scan tool MB991958, read the diagnostic trouble code (DTC)...1359
      INSPECTION PROCEDURE 17: Deceleration Shock....1360
        DIAGNOSIS....1360
          STEP 1. Using scan tool MB991958, read the diagnostic trouble code (DTC)...1360
          STEP 2. Check the idle air control (IAC) motor operation sound...1361
          STEP 3. Using scan tool MB991958, check data list...1361
      INSPECTION PROCEDURE 18: Poor acceleration...1362
        DIAGNOSIS....1362
          STEP 1. Using scan tool MB991958, read the diagnostic trouble code (DTC)...1362
          STEP 2. Using scan tool MB991958, check actuator test items 01, 02, 03, 04, 05, 06: Injector...1363
          STEP 3. Check the ignition timing...1363
          STEP 4. Using scan tool MB991958, check data list...1364
          STEP 5. Using scan tool MB991958, check actuator test...1364
          STEP 6. Using scan tool MB991958, check data list...1365
          STEP 7. Check the fuel pressure...1365
          STEP 8. Check the fuel pressure...1366
      INSPECTION PROCEDURE 19: Surge...1367
        DIAGNOSIS....1367
          STEP 1. Using scan tool MB991958, read the diagnostic trouble code (DTC)...1367
          STEP 2. Using scan tool MB991958, check actuator test items 01, 02, 03, 04, 05, 06: Injector...1368
          STEP 3. Check the ignition timing...1368
          STEP 4. Using scan tool MB991958, check data list and actuator test...1369
          STEP 5. Using scan tool MB991958, check actuator test...1369
          STEP 6. Using scan tool MB991958, check data list...1370
          STEP 7. Check the fuel pressure...1370
          STEP 8. Check the fuel pressure...1371
      INSPECTION PROCEDURE 20: Knocking....1371
        DIAGNOSIS....1371
      INSPECTION PROCEDURE 21: Dieseling...1371
        DIAGNOSIS....1371
      INSPECTION PROCEDURE 22: Too high CO and HC concentration when idling....1371
        DIAGNOSIS....1372
          STEP 1. Using scan tool MB991958, read the diagnostic trouble code (DTC)...1372
          STEP 2. Check the ignition timing...1372
          STEP 3. Using scan tool MB991958, check data list...1373
          STEP 4. Using scan tool MB991958, check data list...1373
          STEP 5. Check the fuel pressure...1374
          STEP 6. Check the following items...1374
      INSPECTION PROCEDURE 23: Transient, Mass Emission Tailpipe Test Failure...1374
        DIAGNOSIS....1374
          STEP 1. Check the exhaust gas with the engine at normal operating temperature...1374
          STEP 2. Check the following items...1375
          STEP 3. Check the drivability...1375
          STEP 4. Using scan tool MB991958, read the diagnostic trouble code (DTC)...1375
          STEP 5. Check the ignition timing...1376
          STEP 6. Using scan tool MB991958, check data list...1376
          STEP 7. Using scan tool MB991958, check data list item 39: Right Bank heated oxygen sensor (front)...1377
          STEP 8. Using scan tool MB991958, check data list item 11: Left Bank Heated oxygen sensor (front)...1377
          STEP 9. Using scan tool MB991958, check data list item 39: Right Bank Heated oxygen sensor (front)...1378
          STEP 10. Check the EGR system...1378
          STEP 11. Using scan tool MB991958, check data list item 69: Right Bank Heated oxygen sensor (rear)...1379
          STEP 12. Using scan tool MB991958, check data list item 11: Left Bank Heated oxygen sensor (front)...1379
          STEP 13. Check the EGR system...1380
          STEP 14. Using scan tool MB991958, check data list item 59: Left Bank Heated oxygen sensor (rear)...1380
          STEP 15. Check the fuel pressure...1380
          STEP 16. Check the following items...1381
      INSPECTION PROCEDURE 24: Purge Flow Test of the Evaporative Emission Canister Failure...1382
        DIAGNOSIS....1382
          STEP 1. Using scan tool MB991958, read the diagnostic trouble code (DTC)...1382
      INSPECTION PROCEDURE 25: Pressure Test of the Evaporative System Failure...1383
        DIAGNOSIS....1383
          STEP 1. Check the evaporative emission purge solenoid....1383
          STEP 2. Check the evaporative emission ventilation solenoid...1383
      INSPECTION PROCEDURE 26: Incorrect Idle Speed When the A/C is Operating (A/C Switch 2 Signal)....1384
        DIAGNOSIS....1385
          STEP 1. Check harness connector C-90 at PCM for damage...1385
          STEP 2. Measure the output voltage at PCM harness side connector C-90...1385
      INSPECTION PROCEDURE 27: A/C condenser fan is inoperative....1386
        DIAGNOSIS....1387
          STEP 1. Check harness connector C-89 at PCM for damage...1387
          STEP 2. Measure the output voltage at PCM harness side connector C-89...1387
      INSPECTION PROCEDURE 28: Power supply system and ignition switch-IG system...1388
        DIAGNOSIS....1390
          STEP 1. Check harness connector C-59 at MFI relay for damage...1390
          STEP 2. Check the MFI relay....1390
          STEP 3. Measure the power supply voltage at MFI relay harness side connector C-59...1391
          STEP 4. Check harness connector C-91 at PCM for damage...1391
          STEP 5. Measure the ignition switch-IG signal voltage at PCM harness side connector C-91...1392
          STEP 6. Measure the backup power supply voltage at PCM harness side connector C-90...1393
          STEP 7. Check for continuity at PCM harness side connector C-90...1394
          STEP 8. Measure the power supply voltage at PCM harness side connector C-90...1395
          STEP 9. Measure the power supply voltage at PCM harness side connector C-90...1396
      INSPECTION PROCEDURE 29: Fuel pump system...1397
        DIAGNOSIS....1399
          STEP 1. Using scan tool MB991958, check actuator test item 07: Fuel Pump...1399
          STEP 2. Check harness connector E-26 at fuel pump for damage...1399
          STEP 3 Check the fuel pump operation...1400
          STEP 4. Check for continuity at fuel pump harness side connector E-26...1400
          STEP 5. Check harness connector C-60 at fuel pump relay for damage...1401
          STEP 6. Check the fuel pump relay....1401
          STEP 7. Measure the power supply voltage at fuel pump relay connector C-60...1402
          STEP 8. Check for open circuit and short circuit to ground and harness damage between fuel pump r...1403
          STEP 9. Check harness connector C-89 at PCM for damage...1403
          STEP 10. Measure the power supply voltage at PCM connector C-89...1404
      INSPECTION PROCEDURE 30: Ignition Switch-ST System and Transmission Range Switch System...1405
        DIAGNOSIS....1407
          STEP 1. Check connector A-50X at starter relay for damage...1407
          STEP 2. Check the starter relay...1407
          STEP 3. Measure the power supply voltage at starter relay connector A-50X...1407
          STEP 4. Check for continuity at starter relay harness side connector A-50X...1408
          STEP 5. Measure the power supply voltage at starter relay connector A-50X...1408
          STEP 6. Check connector B-01 at transmission range switch for damage...1409
          STEP 7. Check the transmission range switch...1409
          STEP 8. Measure the power supply voltage at transmission range switch connector B-01...1409
          STEP 9. Check for open circuit and short circuit to ground and harness damage between transmissio...1410
          STEP 10. Check connector C-90 at PCM for damage...1410
          STEP 11. Check for open circuit and short circuit to ground and harness damage between starter re...1411
      INSPECTION PROCEDURE 31: Ignition Circuit System...1412
        DIAGNOSIS....1414
          STEP 1. Check harness connectors A-44, A-45, A-46 at ignition coil for damage...1414
          STEP 2. Check the ignition coil...1414
          STEP 3. Check harness connectors A-05, A-06 at ignition power transistor for damage...1414
          STEP 4. Check the ignition power transistor...1415
          STEP 5. Measure the power supply voltage at ignition coil connectors A-44, A-45, A-46...1415
          STEP 6. Measure the power supply voltage at ignition power transistor connector A-06...1416
          STEP 7. Measure the power supply voltage at ignition power transistor connector A-05...1416
          STEP 8. Check for continuity at ignition power transistor harness side connector A-05...1417
          STEP 9. Measure the circuit at ignition power transistor connector A-05...1417
          STEP 10. Check harness connector C-89 at PCM for damage...1418
          STEP 11. Check for open circuit between ignition power transistor connector A-05 (terminals No. 1...1418
          STEP 12. Measure the circuit at ignition power transistor connector A-05...1419
          STEP 13. Check harness connector C90 at PCM for damage...1419
          STEP 14. Check for open circuit between ignition power transistor connector A-05 (terminal No. 5)...1420
      INSPECTION PROCEDURE 32: A/C system...1421
        DIAGNOSIS....1422
          STEP 1. Check harness connector C-89, C-91 at PCM for damage...1422
          STEP 2. Check the circuit at PCM connector C-89...1422
          STEP 3. Check the circuit at PCM connector C-91...1423
      CHECK PROCEDURE WITH OSCILLOSCOPE....1447
        VOLUME AIRFLOW SENSOR....1447
        CAMSHAFT POSITION SENSOR AND CRANKSHAFT POSITION SENSOR....1449
        INJECTOR....1451
        IDLE AIR CONTROL MOTOR (STEPPER MOTOR)....1453
        IGNITION COIL AND IGNITION POWER TRANSISTOR....1455
    SPECIAL TOOLS....1457
    ON-VEHICLE SERVICE....1459
      THROTTLE BODY CLEANING....1465
      THROTTLE POSITION SENSOR ADJUSTMENT....1465
      BASIC IDLE SPEED ADJUSTMENT....1467
      FUEL PRESSURE TEST....1468
      FUEL PUMP CONNECTOR DISCONNECTION (HOW TO REDUCE PRESSURIZED FUEL LINES)....1471
      FUEL PUMP OPERATION CHECK....1472
      MULTIPORT FUEL INJECTION RELAY AND FUEL RELAY CHECK....1473
      INTAKE AIR TEMPERATURE SENSOR CHECK....1473
      ENGINE COOLANT TEMPERATURE SENSOR CHECK....1474
      THROTTLE POSITION SENSOR CHECK....1474
      HEATED OXYGEN SENSOR CHECK....1475
      INJECTOR CHECK....1481
        Measurement of Resistance between Terminals....1481
      IDLE AIR CONTROL MOTOR CHECK....1481
      EVAPORATIVE EMISSION PURGE SOLENOID CHECK....1483
      EGR SOLENOID CHECK....1483
    INJECTOR....1484
      REMOVAL SERVICE POINT....1485
      INSTALLATION SERVICE POINTS....1485
    THROTTLE BODY ASSEMBLY....1486
      INSTALLATION SERVICE POINT....1487
      DISASSEMBLY SERVICE POINTS....1488
      ASSEMBLY SERVICE POINTS....1489
      INSPECTION....1490
        DASH POT....1490
    SPECIFICATIONS....1491
GR00003600-23....1493
  AUTOMATIC TRANSMISSION....1493
GR00003900-23B....1495
  AUTOMATIC TRANSMISSION OVERHAUL....1495
    GENERAL INFORMATION....1497
    SPECIAL TOOLS....1501
    TRANSMISSION AND EXTENSION HOUSING....1506
      ASSEMBLY SERVICE POINTS....1506
    TRANSMISSION AND TRANSFER....1508
      ASSEMBLY SERVICE POINT....1508
    EXTENSION HOUSING....1509
      ASSEMBLY SERVICE POINTS....1510
    TRANSFER CASE ADAPTER....1511
      ASSEMBLY SERVICE POINTS....1512
    TRANSMISSION....1513
      DISASSEMBLY....1518
      ASSEMBLY....1526
    REVERSE AND OVERDRIVE CLUTCHES....1548
      DISASSEMBLY SERVICE POINT....1549
      ASSEMBLY SERVICE POINTS....1549
    SECOND BRAKE....1552
      ASSEMBLY SERVICE POINT....1552
    LOW REVERSE ANNULUS GEAR....1553
      ASSEMBLY SERVICE POINTS....1553
    CENTER SUPPORT....1555
      DISASSEMBLY SERVICE POINT....1555
      ASSEMBLY SERVICE POINTS....1556
    UNDERDRIVE CLUTCH....1557
      DISASSEMBLY SERVICE POINT....1558
      ASSEMBLY SERVICE POINTS....1558
    VALVE BODY....1561
      DISASSEMBLY SERVICE POINT....1564
      ASSEMBLY SERVICE POINTS....1564
    TRANSFER....1567
      DISASSEMBLY SERVICE POINT....1570
      ADJUSTMENT BEFORE ASSEMBLY....1570
      ASSEMBLY SERVICE POINTS....1571
      INSPECTION....1577
    TRANSFER CASE PLATE....1578
      ASSEMBLY SERVICE POINTS....1578
    INPUT GEAR....1579
      DISASSEMBLY SERVICE POINT....1580
      ASSEMBLY SERVICE POINTS....1580
    COUNTERSHAFT GEAR....1581
      DISASSEMBLY SERVICE POINTS....1581
      ASSEMBLY SERVICE POINTS....1582
    2-4WD SYNCHRONIZER....1583
      ASSEMBLY SERVICE POINTS....1584
      INSPECTION....1585
    CENTER DIFFERENTIAL CASE....1586
      ASSEMBLY SERVICE POINTS....1586
    REAR OUTPUT SHAFT....1587
      DISASSEMBLY SERVICE POINT....1588
      ASSEMBLY SERVICE POINTS....1588
    TRANSFER DRIVE SHAFT....1589
      DISASSEMBLY SERVICE POINT....1589
      ASSEMBLY SERVICE POINTS....1590
    FRONT OUTPUT SHAFT....1590
      DISASSEMBLY SERVICE POINT....1591
      ASSEMBLY SERVICE POINTS....1591
    SPEEDOMETER GEAR....1592
      ASSEMBLY SERVICE POINT....1592
    SPECIFICATIONS....1593
GR00004000-00E....1601
  GENERAL <ELECTRICAL>....1601
    HARNESS CONNECTOR INSPECTION....1602
      CONNECTOR CONTINUITY AND VOLTAGE TEST....1602
      IMPROPER TERMINAL ENGAGEMENT CHECK....1602
      CONNECTOR TERMINAL ENGAGEMENT AND DISENGAGEMENT....1603
    HOW TO DIAGNOSE....1605
      INSPECTION....1607
      INSPECTION INSTRUMENTS....1607
      CHECKING SWITCHES....1609
      CHECKING RELAYS....1610
      CHECKING FUSES....1611
        CAUTIONS IN EVENT OF BLOWN FUSE....1611
      CABLES AND WIRES CHECK....1612
      BATTERY HANDLING....1612
      GENERAL ELECTRICAL SYSTEM CHECK....1613
        STEP 1. Remove the blown fuse and connect the test light across the fuse terminals (Circuit switc...1613
        STEP 2. Turn the switch ON and disconnect the illumination light connector...1614
GR00004100-26....1617
  FRONT AXLE....1617
    GENERAL DESCRIPTION....1618
    FRONT AXLE DIAGNOSIS....1618
      SYMPTOM PROCEDURES....1619
      INSPECTION PROCEDURE 1: Noise during Wheel Rotation....1619
        DIAGNOSIS....1619
          STEP 1. Check the housing tube and inner shaft for bending...1619
          STEP 2. Check the inner shaft bearing for wear...1619
          STEP 3. Check the driveshaft assembly for wear, damage or bending...1619
          STEP 4. Retest the system...1619
      INSPECTION PROCEDURE 2: Noise Due to Excessive Wheel Play in Turning Direction....1619
        DIAGNOSIS....1619
          STEP 1. Check for play in the inner shaft and side gear serration, the driveshaft and side gear, ...1619
          STEP 2. Retest the system...1619
      INSPECTION PROCEDURE 3: Constant Noise....1620
        DIAGNOSIS....1620
          STEP 1. Check the oil level...1620
          STEP2. Check the tooth contact (engagement) of the drive gear and drive pinion. Refer to P.26-41...1620
          STEP3. Check the side bearing for looseness, wear or damage...1620
          STEP 4. Check the drive pinion bearing for wear or damage...1620
          STEP 5. Check the drive gear and drive pinion for wear...1620
          STEP 6. Check the side gear thrust washer or pinion shaft for wear...1620
          STEP 7. Check the drive gear and differential case for strain, and the gear for damage...1621
          STEP 8. Check for the engagement of foreign material...1621
          STEP 9. Retest the system...1621
      INSPECTION PROCEDURE 4: Gear Noise While Driving....1621
        DIAGNOSIS....1621
          STEP 1. Check the oil level...1621
          STEP 2. Check the gear engagement...1621
          STEP 3. Check the drive pinion turning torque. Refer to P.26-49...1621
          STEP 4. Check the gear for damage...1622
          STEP 5. Check for the engagement of foreign material...1622
          STEP 6. Retest the system...1622
          STEP 7. Retest the system...1622
      INSPECTION PROCEDURE 5: Gear Noise while Coasting....1622
        DIAGNOSIS....1622
          STEP 1. Check the drive pinion turning torque. Refer to P.26-49...1622
          STEP 2. Check the gear for damage...1622
          STEP 3. Retest the system...1622
      INSPECTION PROCEDURE 6: Bearing Noise While Driving or Coasting....1623
        DIAGNOSIS....1623
          STEP 1. Check the drive pinion rear bearing for cracks or damage...1623
          STEP 2. Retest the system...1623
      INSPECTION PROCEDURE 7: Noise while Turning....1623
        DIAGNOSIS....1623
          STEP 1. Check the side bearing for wear or damage...1623
          STEP 2. Check the side gear, pinion gear or pinion shaft for damage...1623
          STEP 3. Retest the system...1623
      INSPECTION PROCEDURE 8: Heat....1624
        DIAGNOSIS....1624
          STEP 1. Check the oil level...1624
          STEP 2. Check the gear backlash (excessive) Refer to P.26-49...1624
          STEP 3. Retest the system...1624
      INSPECTION PROCEDURE 9: Oil leakage....1625
        DIAGNOSIS....1625
          STEP 1. Check the vent plug for clogging...1625
          STEP 2. Check the cover installation...1625
          STEP 3. Check the oil seal for wear or damaged...1625
          STEP 4. Check the oil level...1625
          STEP 5. Retest the system...1625
    SPECIAL TOOLS....1626
    ON-VEHICLE SERVICE....1630
      FRONT AXLE TOTAL BACKLASH CHECK....1630
      FRONT AXLE GEAR OIL LEVEL CHECK....1630
      DRIVE SHAFT END PLAY CHECK....1631
    FRONT AXLE HUB ASSEMBLY....1632
      REMOVAL SERVICE POINTS....1632
      INSTALLATION SERVICE POINT....1633
      DISASSEMBLLY SERVICE POINTS....1635
      ASSEMBLY SERVICE POINTS....1636
    KNUCKLE....1637
      REMOVAL SERVICE POINT....1638
      INSPECTION....1638
        DISASSEMBLY SERVICE POINT....1639
        ASSEMBLY SERVICE POINTS....1640
    DRIVE SHAFT ASSEMBLY....1641
      REMOVAL SERVICE POINTS....1642
      INSTALLATION SERVICE POINTS....1643
      DISASSEMBLY SERVICE POINTS....1645
      ASSEMBLY SERVICE POINTS....1646
      BJ BOOT (RESIN BOOT) REPLACEMENT....1647
    INNER SHAFT ASSEMBLY....1651
      REMOVAL SERVICE POINTS....1651
      INSTALLATION SERVICE POINT....1652
      DISASSEMBLY SERVICE POINT....1653
      ASSEMBLY SERVICE POINTS....1654
    DIFFERENTIAL CARRIER ASSEMBLY....1656
      REMOVAL SERVICE POINT....1657
      INSTALLATION SERVICE POINTS....1657
      DISASSEMBLY SERVICE POINTS....1658
      ASSEMBLY SERVICE POINTS....1668
    SPECIFICATIONS....1676
GR00004200-25....1679
  PROPELLER SHAFT....1679
    GENERAL DESCRIPTION....1680
      CONSTRUCTION DIAGRAM....1680
    PROPELLER SHAFT DIAGNOSIS....1681
      SYMPTOM PROCEDURES....1681
      INSPECTION PROCEDURE 1: Noise at Start....1681
        DIAGNOSIS....1681
          STEP 1. Check if the propeller shaft mounting bolts and nuts are loose. (Refer to P.25-6.)....1681
          STEP 2. Check the universal joint's journal bearing of front propeller shaft for wear or damage. ...1681
          STEP 3. Check the BJ assembly's spline of front propeller shaft for wear...1681
          STEP 4. Check the flange sleeve spline of rear propeller shaft for wear...1682
          STEP 5. Retest the system...1682
      INSPECTION PROCEDURE 2: Noise and Vibration at High Speed....1682
        DIAGNOSIS....1682
          STEP 1. Check the front propeller shaft run-out...1682
          STEP 2. Check the front propeller shaft snap rings thickness. (Refer to P.25-10.)....1682
          STEP 3. Check the front propeller shaft journal bearings for wear or damage. (Refer to P.25-10.)....1682
          STEP 4. Check the rear propeller shaft for wear or damage. (Refer to P.25-9.)....1682
          STEP 5. Retest the system...1683
    SPECIAL TOOL....1683
    PROPELLER SHAFT....1684
      REMOVAL SERVICE POINT....1685
      INSTALLATION SERVICE POINT....1686
      INSPECTION....1687
        DISASSEMBLY SERVICE POINTS....1689
        ASSEMBLY SERVICE POINTS....1691
    SPECIFICATIONS....1694
GR00004300-27....1697
  REAR AXLE....1697
    GENERAL DESCRIPTION....1698
    REAR AXLE DIAGNOSIS....1698
      SYMPTOM PROCEDURES....1699
      INSPECTION PROCEDURE 1: Noise while Wheels are Rotating....1699
        DIAGNOSIS....1699
          STEP 1. Check whether the axle shaft is bent...1699
          STEP 2. Check the axle shaft bearing for wear or damage...1699
          STEP 3. Retest the system...1699
      INSPECTION PROCEDURE 2: Grease Leakage....1699
        DIAGNOSIS....1699
          STEP 1. Check the oil seal for wear or damage, and the bearing seal for defects...1699
          STEP 2. Retest the system...1699
      INSPECTION PROCEDURE 3: Constant Noise <Conventional Differential>....1699
        DIAGNOSIS....1699
          STEP 1. Check the oil level...1699
          STEP 2. Check the tooth contact (engagement) of the drive gear and drive pinion. Refer to GROUP 2...1700
          STEP 3. Check the side bearing for looseness, wear or damage...1700
          STEP 4. Check the drive pinion bearing for wear or damage...1700
          STEP 5. Check the drive gear and drive pinion for wear...1700
          STEP 6. Check the side gear thrust washer or pinion shaft for wear...1700
          STEP 7. Check the drive gear and differential case for strain, and the gear for damage...1700
          STEP 8. Check for the engagement of foreign material...1700
          STEP 9. Retest the system...1700
      INSPECTION PROCEDURE 4: Gear Noise while Driving <Conventional Differential>....1701
        DIAGNOSIS....1701
          STEP 1. Check the oil level...1701
          STEP 2. Check the gear engagement...1701
          STEP 3. Check the drive pinion turning torque...1701
          STEP 4. Check the gear for damage...1701
          STEP 5. Check for foreign material...1701
          STEP 6. Retest the system...1701
      INSPECTION PROCEDURE 5: Gear Noise while Coasting <Conventional Differential>....1702
        DIAGNOSIS....1702
          STEP 1. Check the drive pinion turning torque...1702
          STEP 2. Check the gear for damage...1702
          STEP 3. Retest the system...1702
      INSPECTION PROCEDURE 6: Bearing Noise while Driving or Coasting <Conventional Differential>....1702
        DIAGNOSIS....1702
          STEP 1. Check the drive pinion rear bearing for cracks or damage...1702
          STEP 2. Retest the system...1702
      INSPECTION PROCEDURE 7: Noise while Turning <Conventional Differential>....1702
        DIAGNOSIS....1702
          STEP 1. Check the side bearing for wear or damage...1702
          STEP 2. Check the side gear, pinion gear or pinion shaft for damage...1702
          STEP 3. Retest the system...1702
      INSPECTION PROCEDURE 8: Heat <Conventional Differential>....1703
        DIAGNOSIS....1703
          STEP 1. Check the oil level...1703
          STEP 2. Check the gear backlash (excessive). Refer to GROUP 26, Differential Carrier - Inspection...1703
          STEP 3. Retest the system...1703
      INSPECTION PROCEDURE 9: Oil Leakage <Conventional Differential>....1704
        DIAGNOSIS....1704
          STEP 1. Check the breather hose for clogging...1704
          STEP 2. Check the cover installation...1704
          STEP 3. Check the oil seal for wear or damaged...1704
          STEP 4. Check the oil level...1704
          STEP 5. Retest the system...1704
      INSPECTION PROCEDURE 10: Abnormal Noise during Driving or Shifting <Limited-Slip Differential>....1704
        DIAGNOSIS....1704
          STEP 1. Check for looseness in the companion flange tightening nut...1704
          STEP 2. Check the drive gear backlash (excessive)...1705
          STEP 3. Retest the system...1705
      INSPECTION PROCEDURE 11: Abnormal Noise when Cornering <Limited-Slip Differential>....1705
        DIAGNOSIS....1705
          STEP 1. Check that Hypoid gear oil MITSUBISHI Genuine Gear Oil Part No.8149630 EX or equivalent i...1705
          STEP 2. Check the oil level...1705
          STEP 3. Check the limited slip differential case assembly for damage...1705
          STEP 4. Retest the system...1705
      INSPECTION PROCEDURE 12: Gear Noise <Limited-Slip Differential>....1706
        DIAGNOSIS....1706
          STEP 1. Check that Hypoid gear oil MITSUBISHI Genuin Gear Oil Part No.8149630 EX or equivalent is...1706
          STEP 2. Check the oil level...1706
          STEP 3. Check the tooth contact (engagement) of the drive gear. Refer to GROUP 26, Differential C...1706
          STEP 4. Check the drive gear backlash...1706
          STEP 5. Check the drive pinion turning torque...1706
          STEP 6. Check the drive gear and drive pinion for tooth damage or breakage...1707
          STEP 7. Check the drive pinion bearing and side bearing for seizure, damage or breakage...1707
          STEP 8. Check the limited slip differential case assembly for damage...1707
          STEP 9. Retest the system...1707
      INSPECTION PROCEDURE 13: Gear Oil Leakage <Limited-Slip Differential>....1707
        DIAGNOSIS....1707
          STEP 1. Check for looseness in the filler or drain plug...1707
          STEP 2. Check the breather hose for clogging or damage...1707
          STEP 3. Check for looseness in the companion flange tightening nut...1707
          STEP 4. Check the oil seal for wear, damage or foreign material...1707
          STEP 5. Retest the system...1707
      INSPECTION PROCEDURE 14: Seizure <Limited-Slip Differential>....1708
        DIAGNOSIS....1708
          STEP 1. Check that Hypoid gear oil MITSUBISHI Genuine Gear Oil Part No.8149630 EX or equivalent i...1708
          STEP 2. Check the oil level...1708
          STEP 3. Check the drive gear backlash (low)...1708
          STEP 4. Check the drive pinion turning torque (excessive)...1708
          STEP 5. Check the side bearing preload (excessive)...1708
          STEP 6. Retest the system...1708
      INSPECTION PROCEDURE 15: Breakdown <Limited-Slip Differential>....1709
        DIAGNOSIS....1709
          STEP 1. Check for looseness of the drive gear tightening bolt...1709
          STEP 2. Check the drive gear backlash. Refer to GROUP 26, Differential Carrier - Inspection Befor...1709
          STEP 3. Check the drive pinion turning torque (low). Refer to P.27-34...1709
          STEP 4. Check the side bearing preload (low)...1709
          STEP 5. Retest the system...1709
      INSPECTION PROCEDURE 16: Limited Slip Differential does not Function (On Snow, Mud, Ice, etc.) <L...1709
        DIAGNOSIS....1709
          STEP 1. Check the limited slip device for damage...1709
          STEP 2. Retest the system...1709
    SPECIAL TOOLS....1710
    ON-VEHICLE SERVICE....1713
      REAR AXLE TOTAL BACKLASH CHECK....1713
      AXLE SHAFT END PLAY CHECK....1713
      AXLE SHAFT END PLAY ADJUSTMENT....1713
      GEAR OIL LEVEL CHECK....1714
    AXLE ASSEMBLY....1715
      REMOVAL SERVICE POINTS....1716
      INSTALLATION SERVICE POINTS....1716
    AXLE SHAFT ASSEMBLY....1717
      REMOVAL SERVICE POINTS....1718
      INSTALLATION SERVICE POINT....1718
      DISASSEMBLY SERVICE POINTS....1720
      ASSEMBLY SERVICE POINTS....1721
      INSPECTION....1723
    DIFFERENTIAL CARRIER ASSEMBLY....1724
      REMOVAL SERVICE POINTS....1724
      INSTALLATION SERVICE POINT....1725
      DISASSEMBLY SERVICE POINTS....1727
      ASSEMBLY SERVICE POINTS....1732
    SPECIFICATIONS....1740
GR00004400-42....1743
  BODY....1743
    BODY MOUNTING....1746
    HOOD....1747
      BODY DIAGNOSIS....1747
      SYMPTOM PROCEDURES....1747
      INSPECTION PROCEDURE 1: Difficult Locking and Unlocking....1747
        STEP 1. Check the release cable routing condition...1747
        STEP 2. Check the engagement of the hood latch and hood striker...1747
        STEP 3. Check for proper lubrication of release cable...1747
        STEP 4. Retest the system...1747
      INSPECTION PROCEDURE 2: Uneven Body Clearance....1748
        STEP 1. Check the hood installation condition...1748
        STEP 2. Retest the system...1748
      INSPECTION PROCEDURE 3 : Uneven Height....1748
        STEP 1. Check the hood bumper height...1748
        STEP 2. Retest the system...1748
      HOOD....1749
      INSPECTION....1750
        HOOD SWITCH CONTINUITY CHECK <VEHICLES WITH THEFT-ALARM SYSTEM>....1750
    FENDER....1751
    FUEL FILLER LID....1752
    WINDOW GLASS....1753
      WINDOW GLASS DIAGNOSIS....1753
      SYMPTOM PROCEDURES....1753
      INSPECTION PROCEDURE 1: Water Leak Through Windshield/Water Leak Through Quarter Window Glass/Wat...1753
        STEP 1. Check if the seal is faulty...1753
        STEP 2. Check if the body flange is deformed...1753
        STEP 3. Retest the system...1753
      WINDOW GLASS....1754
      WINDSHIELD....1756
        REMOVAL SERVICE POINT....1757
        INSTALLATION SERVICE POINT....1757
      QUARTER WINDOW GLASS....1759
        REMOVAL SERVICE POINT....1760
        INSTALLATION SERVICE POINT....1760
      LIFTGATE WINDOW GLASS....1761
        REMOVAL SERVICE POINT....1762
        INSTALLATION SERVICE POINT....1762
    DOOR....1763
      OPERATION....1763
      CENTRAL DOOR LOCKING SYSTEM DIAGNOSIS....1764
      SYMPTOM PROCEDURES....1765
      INSPECTION PROCEDURE 1: Only the ETACS-ECU Input Signal Cannot be Checked Using the Scan Tool (MU...1765
        DIAGNOSIS....1766
          STEP 1. Check the harness wire between data link connector C-69 (terminal No.9) and ETACS-ECU con...1766
          STEP 2. Retest the system....1766
      INSPECTION PROCEDURE 2: None of the Door Lock Function Operate...1767
        DIAGNOSIS....1769
          STEP 1. Check ETACS-ECU connector D-11 for loose, corroded or damaged terminals, or terminals pus...1769
          STEP 2. Measure the power supply line voltage at junction block connector D-11...1769
          STEP 3. Check the harness wires between fusible link (8) and ETACS-ECU connector D-11 (terminal N...1770
          STEP 4. Check the harness wires between ETACS-ECU connector D-11 and ground...1771
          STEP 5. Retest the system...1771
      INSPECTION PROCEDURE 3: The other Door(s) do(es) not Lock or Unlock by the Door Switch or the Fro...1772
        DIAGNOSIS....1774
          STEP 1. Choose method of ETACS-ECU input signal check...1775
          STEP 2. Check the input signal (by using the pulse check) (by using MB991958)...1775
          STEP 3. Check the ETACS-ECU input signal from the power window main switch (incorporated with doo...1776
          STEP 4. Check the input signal from the power window sub switch (incorporated with door lock swit...1776
          STEP 5. Check the input signal from the door lock key cylinder switch (RH) (by using a voltmeter)...1776
          STEP 6. Check power window main switch connector F-05 for loose, corroded or damaged terminals, o...1777
          STEP 7. Check the power window main switch (incorporated with door lock switch) continuity...1777
          STEP 8. Check ETACS-ECU connector D-10 <Vehicles without keyless entry system> or D-27 <Vehicles ...1778
          STEP 9. Check the harness wire between ETACS-ECU connector D-10 (terminals No.27 and No.28) <Vehi...1779
          STEP 10. Check the harness wire between power window main switch connector F-05 (terminal No.12) ...1780
          STEP 11. Check power window sub switch connector F-17 for loose, corroded or damaged terminals, o...1780
          STEP 12. Check the power window sub switch (incorporated with door lock switch) continuity...1781
          STEP 13. Check ETACS-ECU connector D-10 <Vehicles without keyless entry system> or D-27 <Vehicles...1781
          STEP 14. Check the harness wire between ETACS-ECU connector D-10 (terminals No.27 and No.28) <Veh...1782
          STEP 15. Check the harness wire between power window sub switch connector F-17 (terminal No.2) an...1783
          STEP 16. Check door lock key cylinder switch (RH) connector F-18 for loose, corroded or damaged t...1783
          STEP 17. Check the door lock key cylinder switch (RH)...1784
          STEP 18. Check ETACS-ECU connector D-10 <Vehicles without keyless entry system> or D-26 <Vehicles...1784
          STEP 19.Check the harness wire between ETACS-ECU connector D-10 (terminals No.27 and No.28) <Vehi...1785
          STEP 20. Check the harness wire between door lock key cylinder switch (RH) connector F-18 (termin...1786
          STEP 21. Retest the system...1786
      INSPECTION PROCEDURE 4: The Other Door(s) do(es) not Lock or Unlock by the Driver's Inside Door L...1787
        DIAGNOSIS....1790
          STEP 1. Choose method of ETACS-ECU input signal check....1790
          STEP 2. Check the input signal (by using the pulse check) (by using MB991958)...1790
          STEP 3. Check the ETACS-ECU input signal from the door lock actuator switch (front: LH) (by using...1791
          STEP 4. Check the input signal from the door lock key cylinder switch (LH) (by using a voltmeter)...1791
          STEP 5. Check door lock actuator (front: LH) connector F-12 for loose, corroded or damaged termin...1791
          STEP 6. Check the front door lock actuator switch (front: LH)...1792
          STEP 7. Check ETACS-ECU connector D-10 <Vehicles without keyless entry system> or D-27 <Vehicles ...1792
          STEP 8. Check the harness wires between ETACS-ECU connector D-10 (terminals No.21, No.23 and No.2...1793
          STEP 9. Check the harness wire between door lock actuator (front: LH) connector F-12 (terminal No...1794
          STEP 10. Check door lock key cylinder switch (LH) connector F-06 for loose, corroded or damaged t...1794
          STEP 11. Check the door lock key cylinder switch (LH)...1795
          STEP 12. Check ETACS-ECU connector D-10 <Vehicles without keyless entry system>, D-26 <Vehicles w...1795
          STEP 13. Check the harness wires between ETACS-ECU connector D-10 (terminal No.26) <Vehicles with...1796
          STEP 14. Check the harness wire between door lock key cylinder switch connector F-06 and ground...1797
          STEP 15. Retest the system...1797
      INSPECTION PROCEDURE 5: Some Doors do not Lock or Unlock...1798
        DIAGNOSIS....1801
          STEP 1. Confirm which door lock actuator is defective...1801
          STEP 2. Check door lock actuator (front: LH) connector F-12 for loose, corroded or damaged termin...1801
          STEP 3. Check the front door lock actuator switch (front: LH)...1802
          STEP 4. Check ETACS-ECU connectors D-10 <Vehicles without keyless entry system> and D-27 <Vehicle...1803
          STEP 5. Check the harness wire between ETACS-ECU connectors D-10 (terminals No.21 and No.24) <Veh...1804
          STEP 6. Check door lock actuator (front: RH) connector F-24 for loose, corroded or damaged termin...1805
          STEP 7. Check the front door lock actuator switch (front: RH)...1806
          STEP 8. Check ETACS-ECU connectors D-10 <Vehicles without keyless entry system> and D-27 <Vehicle...1807
          STEP 9. Check the harness wire between ETACS-ECU connectors D-10 (terminals No.21 and No.24) <Veh...1808
          STEP 10. Check door lock actuator (rear: RH) connector F-21 for loose, corroded or damaged termin...1809
          STEP 11. Check the rear door lock actuator (rear: RH)...1810
          STEP 12. Check ETACS-ECU connectors D-10 <Vehicles without keyless entry system> and D-27 <Vehicl...1811
          STEP 13. Check the harness wire between ETACS-ECU connectors D-10 (terminals No.21 and No.24) <Ve...1812
          STEP 14. Check door lock actuator (rear: LH) connector F-09 for loose, corroded or damaged termin...1813
          STEP 15. Check the rear door lock actuator (rear: LH)...1814
          STEP 16. Check ETACS-ECU connectors D-10 <Vehicles without keyless entry system> and D-27 <Vehicl...1815
          STEP 17. Check the harness wire between ETACS-ECU connectors D-10 (terminals No.21 and No.24) <Ve...1816
          STEP 18. Check door lock actuator (liftgate) connector G-04 for loose, corroded or damaged termin...1817
          STEP 19. Check the door lock actuator (liftgate)...1818
          STEP 20. Check ETACS-ECU connectors D-10 <Vehicles without keyless entry system> and D-27 <Vehicl...1819
          STEP 21. Check the harness wire between ETACS-ECU connectors D-10 (terminals No.21 and No.24) <Ve...1820
          STEP 22. Retest the system...1821
      INSPECTION PROCEDURE 6: Forgotten Key Prevention Function does not Operate (Center Door Locking S...1822
        DIAGNOSIS....1824
          STEP 1.Choose method of ETACS-ECU input signal check...1824
          STEP 2. Check the input signal (by using the pulse check) (by using MB991958)...1824
          STEP 3. Check the ETACS-ECU input signal from the key reminder switch (by using a voltmeter)...1825
          STEP 4. Check the input signal from the front driver's door switch (by using a voltmeter)...1825
          STEP 5. Check the input signal from the Front passenger's door switch (by using a voltmeter)...1825
          STEP 6. Check key reminder switch connector D-16 for loose, corroded or damaged terminals, or ter...1826
          STEP 7. Check the key reminder switch...1826
          STEP 8. Check ETACS-ECU connector D-11 for loose, corroded or damaged terminals, or terminals pus...1826
          STEP 9. Check the harness wire between ETACS-ECU connector D-11 (terminal No.8) and key reminder ...1827
          STEP 10. Check the harness wire between key reminder switch connector D-16 (terminal No.4) and gr...1828
          STEP 11. Check front driver's door switch connector E-33 for loose, corroded or damaged terminals...1828
          STEP 12. Check the front driver’s door switch...1828
          STEP 13. Check ETACS-ECU connector D-11 and D-27 for loose, corroded or damaged terminals, or ter...1829
          STEP 14. Check the harness wire between ETACS-ECU connector D-11 (terminal No.9), D-27 (terminal ...1830
          STEP 15. Check front passenger’s door switch conn....1831
          STEP 16. Check the front passenger’s door switch...1832
          STEP 17. Check ETACS-ECU connector D-26 and D-27 for loose, corroded or damaged terminals, or ter...1832
          STEP 18. Check the harness wire between ETACS-ECU connector D-26 (terminal No.23), D-27 (terminal...1833
          STEP 19.Retest the system...1834
      POWER WINDOW DIAGNOSIS....1835
      SYMPTOM PROCEDURES....1836
      INSPECTION PROCEDURE 1: All Windows does not Open or Close Using the Power Window Main/Sub Switch...1836
        DIAGNOSIS....1837
          STEP 1. Check power window relay connector C-75X for loose, corroded or damaged terminals, or ter...1837
          STEP 2. Measure the power window relay continuity...1838
          STEP 3. Measure the power window relay supply circuit [ignition switch (IG2)] at the power window...1838
          STEP 4. Check the harness wire between ignition switch (IG2) and power window relay connector C-7...1839
          STEP 5. Check the power window relay supply circuit [fusible link (10)] at power window relay con...1840
          STEP 6. Check the harness wire between fusible link (10) and power window relay connector C-75X (...1840
          STEP 7. Measure the power window relay supply circuit at power window relay connector C-75X...1841
          STEP 8. Check the harness wire between power window relay connector C-75X (terminal No.2) and gro...1841
          STEP 9. Check power window main switch connector F-05 for loose, corroded or damaged terminals, o...1841
          STEP 10. Check the power supply circuit [power window relay] at power window main switch connecto...1842
          STEP 11. Check the harness wire between power window relay connector C-75X (terminal No.1) and po...1842
          STEP 12. Measure the power window main switch ground circuit at power window main switch connecto...1843
          STEP 13. Check the harness wire between power window main switch connector F-05 (terminal No.12) ...1843
          STEP 14. Retest the system...1844
      INSPECTION PROCEDURE 2: All Windows does not Open or Close Using the Power Window Main/Sub Switch...1845
        DIAGNOSIS....1846
          STEP 1. Choose method of ETACS-ECU input signal check...1846
          STEP 2. Check the ETACS-ECU input signal from the ignition switch (by using the pulse check) (by ...1847
          STEP 3. Check the ETACS-ECU input signal from the ignition switch (by using a voltmeter)...1847
          STEP 4. Check ETACS-ECU connector D-11 for loose, corroded or damaged terminals, or terminals pus...1848
          STEP 5. Measure the ETACS-ECU power supply circuit ignition switch (IG1) at ETACS- ECU connector ...1848
          STEP 6. Check the harness wire between ignition switch (IG1) and ETACS-ECU connector D-11...1849
          STEP 7. Check power window relay connector C-75X for loose, corroded or damaged terminals, or ter...1849
          STEP 8. Measure the power window relay continuity...1850
          STEP 9. Measure the power window relay supply circuit [ETACS-ECU] at the power window relay conne...1850
          STEP 10. Check ETACS-ECU connector D-26 for loose, corroded or damaged terminals, or terminals pu...1851
          STEP 11. Check the harness wire between ETACS-ECU connector D-26 (terminal No.26) and power windo...1851
          STEP 12. Measure the power window relay supply circuit at power window relay connector C-75X...1852
          STEP 13. Check the harness wire between power window relay connector C-75X (terminal No.2) and gr...1852
          STEP 14. Check the power window relay supply circuit [fusible link (10)] at power window relay co...1853
          STEP 15. Check the harness wire between fusible link (10) and power window relay connector C-75X ...1853
          STEP 16. Check power window main switch connector F-05 for loose, corroded or damaged terminals, ...1854
          STEP 17. Check the power supply circuit [power window relay] at power window main switch connecto...1854
          STEP 18. Check the harness wire between power window relay connector C-75X (terminal No.1) and po...1855
          STEP 19. Measure the power window main switch ground circuit at power window main switch connecto...1856
          STEP 20. Check the harness wire between power window main switch connector F-05 (terminal No.12) ...1856
          STEP 21. Retest the system...1857
      INSPECTION PROCEDURE 3: Power Window Timer Function does not Work Normally. (Power Window Operate...1857
        DIAGNOSIS....1858
          STEP 1. Choose method of the ETACS-ECU input signal check...1858
          STEP 2. Check the ETACS-ECU input signal from the ignition switch (by using the pulse check) (by ...1859
          STEP 3. Check the ETACS-ECU input signal from the....1859
          STEP 4. Check the input signal from the ignition switch (by using a voltmeter)...1860
          STEP 5. Check driver's door switch connector E-33....1860
          STEP 6. Check the front door switch...1861
          STEP 7. Check ETACS-ECU connector D-11 and D-26 for loose, corroded or damaged terminals, or term...1861
          STEP 8. Check the harness wire between ETACS-ECU connector D-11 (terminal No.9), D-26 (terminal N...1862
          STEP 9. Check ETACS-ECU connector D-11 for loose, corroded or damaged terminals, or terminals pus...1863
          STEP 10. Check the harness wire between ETACS-ECU connector D-11 (terminal No.3) and ignition swi...1863
          STEP 11. Retest the system...1864
      DOOR DIAGNOSIS....1864
      SYMPTOM PROCEDURES....1865
      INSPECTION PROCEDURE 1: Water Leak Through Door Window Glass....1865
        STEP 1. Check the door window glass installation...1865
        STEP 2. Check the clearance at the top of the window glass...1865
        STEP 3. Retest the system...1865
      INSPECTION PROCEDURE 2: Door Window Malfunction....1865
        STEP 1. Check the door window installation condition...1865
        STEP 2. Check the door sash...1865
        STEP 3. Inspect the window regulator assembly...1865
        STEP 4. Retest the system...1865
      INSPECTION PROCEDURE 3: Water Leak through Door Edge....1866
        STEP 1. Check the weatherstrip...1866
        STEP 2. Check door fit (alignment)...1866
        STEP 3. Retest the system...1866
      INSPECTION PROCEDURE 4: Water Leak From Door Center....1866
        STEP 1. Check the drain hole...1866
        STEP 2. Check the waterproof film...1866
        STEP 3. Retest the system...1866
      INSPECTION PROCEDURE 5: Door Hard to Open....1866
        STEP 1. Adjust the latch and striker engagement...1866
        STEP 2. Check for possible lock rod damage...1866
        STEP 3. Check door handle flexibility (amount of movement of handle required to open door)...1866
        STEP 4. Retest the system...1866
      INSPECTION PROCEDURE 6: Door does not Open or Close Completely...1867
        STEP 1. Check the door hinge position...1867
        STEP 2. Check the door...1867
        STEP 3. Check the grease...1867
        STEP 4. Retest the system...1867
      INSPECTION PROCEDURE 7: Uneven Gap Between Body....1867
      INSPECTION PROCEDURE 8: Wind Noise Around Door....1867
        STEP 1. Check the weatherstrip for holding condition...1867
        STEP 2. Check the weatherstrip and molding for installation condition...1867
        STEP 3. Check the clearance...1867
        STEP 4. Check the door...1867
        STEP 5. Retest the system...1867
      HOW TO LOCATE WIND NOISES....1868
      ON-VEHICLE SERVICE....1871
      DOOR FIT ADJUSTMENT....1871
      DOOR WINDOW GLASS ADJUSTMENT....1872
      ADJUSTMENT AND REPLACEMENT WHEN THERE IS A MALFUNCTION OF THE POWER WINDOWS....1872
      DOOR OUTSIDE HANDLE PLAY CHECK....1873
      POWER WINDOW OPERATING CURRENT CHECK....1873
      CIRCUIT BREAKER (INCORPORATED IN THE POWER WINDOW MOTOR) CHECK....1873
      DOOR INSIDE HANDLE PLAY CHECK AND ADJUSTMENT....1873
      DOOR ASSEMBLY....1874
        INSTALLATION SERVICE POINT....1875
      INSPECTION....1875
        DOOR SWITCH CONTINUITY CHECK....1875
      DOOR TRIM AND WATERPROOF FILM....1876
        REMOVAL SERVICE POINT....1877
      INSPECTION....1878
        POWER WINDOW SWITCH CONTINUITY CHECK....1878
      DOOR GLASS AND REGULATOR....1879
        REMOVAL SERVICE POINT....1880
        INSTALLATION SERVICE POINTS....1881
      INSPECTION....1881
        POWER WINDOW RELAY CONTINUITY CHECK....1881
        POWER WINDOW MOTOR CHECK....1881
      DOOR HANDLE AND LATCH....1882
        INSTALLATION SERVICE POINTS....1883
      INSPECTION....1884
        FRONT DOOR LOCK ACTUATOR CHECK....1884
        REAR DOOR LOCK ACTUATOR CHECK....1885
        DOOR LOCK KEY CYLINDER SWITCH CONTINUITY CHECK....1886
        CENTER DOOR LOCK SWITCH CONTINUITY CHECK....1886
      WINDOW GLASS RUNCHANNEL AND DOOR OPENING WEATHERSTRIP....1887
        REMOVAL SERVICE POINT....1887
        INSTALLATION SERVICE POINT....1888
    LIFTGATE....1888
      LIFTGATE DIAGNOSIS....1888
      SYMPTOM PROCEDURES....1888
      INSPECTION PROCEDURE 1: Liftgate Hard to Open....1888
        STEP 1. Adjust the latch and striker engagement...1888
        STEP 2. Check for possible lock rod damage...1888
        STEP 3. Check liftgate handle flexibility (amount of movement of handle required to open liftgate)...1889
        STEP 4. Retest the system...1889
      INSPECTION PROCEDURE 2: Liftgate does not Open or Close Completely...1889
        STEP 1. Check the liftgate hinge position...1889
        STEP 2. Check the liftgate...1889
        STEP 3. Check the grease...1889
        STEP 4. Retest the system...1889
      INSPECTION PROCEDURE 3: Uneven Gap between Body....1889
      ON-VEHICLE SERVICE....1890
      LIFTGATE FIT ADJUSTMENT....1890
      LIFTGATE HANDLE PLAY CHECK....1890
      LIFTGATE....1891
        INSTALLATION SERVICE POINT....1892
      LIFTGATE TRIM AND WATERPROOF FILM....1893
      LIFTGATE HANDLE AND LATCH....1894
      INSPECTION....1895
        LIFTGATE LOCK ACTUATOR CHECK....1895
        LIFTGATE LOCK KEY CYLINDER SWITCH CHECK....1895
    KEYLESS ENTRY SYSTEM....1896
      KEYLESS ENTRY SYSTEM DIAGNOSIS....1896
      SYMPTOM PROCEDURES....1897
      INSPECTION PROCEDURE 1: All of the Doors can not be Locked or Unlocked Using the Transmitter. (Ho...1897
        DIAGNOSIS....1897
          STEP 1. Select a tester...1897
          STEP 2. Check the input signal (by using the pulse check mode of the monitor) (by using MB991958)...1898
          STEP 3. Check the keyless entry receiver-ECU input signal (by using a voltmeter)...1898
          STEP 4. Measure the voltage at transmitter battery...1899
          STEP 5. Check the transmitter...1899
          STEP 6. Retest the system...1899
      INSPECTION PROCEDURE 2: The Secret Code cannot be Registered...1899
      INSPECTION PROCEDURE 3: The Dome Light, the Cargo Space Light and the Hazard Warning Lights do no...1900
        DIAGNOSIS....1901
          STEP 1. Verify the keyless entry system...1901
          STEP 2. Check the configuration function...1901
          STEP 3. Check keyless entry receiver-ECU connector E-25 for loose, corroded or damaged terminals,...1901
          STEP 4. Measure the resistance at keyless entry receiver-ECU...1901
          STEP 5. Check ETACS-ECU connector D-27 for loose, corroded or damaged terminals, or terminals pus...1902
          STEP 6. Check the harness wire between keyless entry receiver-ECU connector E-25 (terminal No. 6)...1902
          STEP 7. Retest the system...1903
      ON-VEHICLE SERVICE....1905
      HOW TO REPLACE THE TRANSMITTER BATTERY....1905
      SECRET CODE REGISTRATION METHOD....1905
        WHEN SPECIAL TOOL MB991529 IS USED....1906
        WHEN SPECIAL TOOL MB991824 (V.C.I.) IS USED....1907
      KEYLESS ENTRY SYSTEM....1909
      INSPECTION....1910
        HAZARD WARNING RELAY CONTINUITY CHECK....1910
    SUNROOF ASSEMBLY....1910
      SUNROOF DIAGNOSIS....1910
      SYMPTOM PROCEDURES....1911
      INSPECTION PROCEDURE 1: The Sunroof does not Operate when the Ignition Switch is Turned to "ON"...1911
        DIAGNOSIS....1912
          STEP 1. Check sunroof-ECU connector E-07 for loose, corroded or damaged terminals, or terminals p...1912
          STEP 2. Measure the power supply line voltage at sunroof-ECU connector E-07...1913
          STEP 3. Check the harness wires between ignition switch (IG1) and sunroof-ECU connector E-07 (ter...1913
          STEP 4. Check the harness wires between power window relay connector C-75X (terminal No.1) and su...1915
          STEP 5. Check the harness wire between sunroof-ECU connector E-07 (terminals No.2 and No.6) and g...1915
          STEP 6. Retest the system....1916
      INSPECTION PROCEDURE 2: The Sunroof does not Operate when the Sunroof Switch is Operated...1916
        DIAGNOSIS....1917
          STEP 1. Check sunroof-ECU connector E-07 and sunroof switch connector E-03 for damage for loose, ...1917
          STEP 2. Measure the power supply voltage at sunroof switch connector E-03...1918
          STEP 3. Check the harness wires between sunroof switch connector E-03 (terminal No.1 and 3) and s...1918
          STEP 4. Check the harness wire between sunroof switch connector E-03 (terminal No.4) and ground...1919
          STEP 5. Retest the system...1919
      INSPECTION PROCEDURE 3: The Sunroof Motor does not Operate...1920
        DIAGNOSIS....1921
          STEP 1. Check sunroof-ECU connector E-07 and sunroof motor connector E-09 for loose, corroded or ...1921
          STEP 2. Measure the power supply/ground line at sunroof motor connector E-09...1921
          STEP 3. Check the harness wires between sunroof-ECU connector E-07 (terminal No.9 and 10) and sun...1922
          STEP 4. Check the sunroof motor...1922
          STEP 5. Retest the system...1922
      INSPECTION PROCEDURE 4: Sunroof Timer Function does not Work Normally <Vehicles with keyless entr...1923
        DIAGNOSIS....1924
          STEP 1. Choose method of the ETACS-ECU input signal check...1924
          STEP 2. Check the ETACS-ECU input signal from the ignition switch (by using the pulse check) (by ...1925
          STEP 3. Check the ETACS-ECU input signal from the....1925
          STEP 4. Check the input signal from the ignition switch (by using a voltmeter)...1926
          STEP 5. Check driver's door switch connector E-33....1926
          STEP 6. Check the front door switch...1927
          STEP 7. Check ETACS-ECU connector D-11 and D-26 for loose, corroded or damaged terminals, or term...1927
          STEP 8. Check the harness wire between ETACS-ECU connector D-11 (terminal No.9), D-26 (terminal N...1928
          STEP 9. Check ETACS-ECU connector D-11 for loose, corroded or damaged terminals, or terminals pus...1929
          STEP 10. Check the harness wire between ETACS-ECU connector D-11 (terminal No.3) and ignition swi...1929
          STEP 11. Retest the system...1930
      INSPECTION PROCEDURE 5: Safety Mechanism does not Function...1931
        DIAGNOSIS....1932
          STEP 1. Check sunroof-ECU connector E-07 for loose, corroded or damaged terminals, or terminals p...1932
          STEP 2. Measure the power supply line voltage at sunroof-ECU connector E-07...1933
          STEP 3. Check the harness wires between fusible link number 8 and sunroof-ECU connector E-07 (ter...1933
          STEP 4. Check the harness wires between sunroof-ECU connector E-07 (terminals No.2 and No.6) and ...1934
          STEP 5. Retest the system...1935
      ON-VEHICLE SERVICE....1937
      WATER TEST....1937
      SUNROOF FIT ADJUSTMENT....1937
      SUNROOF ASSEMBLY....1942
        REMOVAL SERVICE POINTS....1943
        INSTALLATION SERVICE POINTS....1946
      SUNROOF MOTOR CHECK....1948
      SUNROOF SWITCH CONTINUITY CHECK....1948
    UNDER COVER....1949
    SPECIFICATIONS....1950
GR00004600-52A....1953
  INTERIOR....1953
    GENERAL DESCRIPTION....1955
      OPERATION....1955
    SEAT BELT DIAGNOSIS....1956
      DIAGNOSIS FUNCTION....1956
        HOW TO CONNECT SCAN TOOL (MUT-III)....1956
      SYMPTOM PROCEDURES....1958
      INSPECTION PROCEDURE 1: When the Seat Belt is not Fastened and the Ignition Switch is Turned to t...1958
        DIAGNOSIS....1959
          STEP 1. Measure the power supply line voltage at the junction block connector D-11....1959
          STEP 2. Check the harness wires between fusible link number 6 and ETACS-ECU connector D-11 (termi...1960
          STEP 3. Measure the ignition switch (IG1) line voltage the at the junction block connector D-11...1960
          STEPS 4. Check the harness wires between ignition switch (IG1) and ETACS-ECU connector D-11 (term...1961
          STEP 5. Measure the ground line resistance at the junction block connector D-11...1961
          STEP 6. Check the harness wires between the ETACS-ECU connector D-11 (terminal No. 10) and the gr...1962
          STEP 7. Retest the system...1962
      INSPECTION PROCEDURE 2: When the Seat Belt is not Fastened and the Ignition Switch is Turned to t...1963
        DIAGNOSIS....1964
          STEP 1. Check the input signal (by using pulse check)...1965
          STEP 2. Check the seat belt buckle switch continuity...1965
          STEP 3. Check the harness wires between ETACS-ECU connector D-11 (terminal No. 7) and seat belt b...1966
          STEP 4. Check the harness wire between seat belt buckle switch connector E-35 (terminal No.2) and...1967
          STEP 5. Retest the system...1967
      INSPECTION PROCEDURE 3: When the Seat Belt is not Fastened and the Ignition Switchis Turned to th...1968
        DIAGNOSIS....1969
          STEP 1. Check the seat belt warning light circuit line at junction block connector D-11...1969
          STEP 2. Check the seat belt warning light bulb...1969
          STEP 3. Check the harness wires between the ignition switch (IG1) and junction block connector D-...1970
          STEP 4. Retest the system...1971
    COMPASS AND TEMPERATURE DISPLAY DIAGNOSIS....1972
      SYMPTOM PROCEDURES....1973
      INSPECTIN PROCEDURE 1: There is no Display...1973
        DIAGNOSIS....1975
          STEP 1. Measure the voltage at inside rear view mirror (with compass and temperature display) pow...1975
          STEP 2. Check harness connector E-59 at the inside rear view mirror (with compass and temperature...1975
          STEP 3. Check the harness wires between the inside rear view mirror (with compass and temperature...1976
          STEP 4. Measure the resistance at the inside rear view mirror (with compass and temperature displ...1978
          STEP 5. Check the harness wires between inside rear view mirror (with compass and temperature dis...1979
          STEP 6. Check the symptoms...1979
      INSPECTION PROCEDURE 2: The Advance Direction is Devited...1980
        DIAGNOSIS....1980
      INSPECTION PROCEDURE 3: The Compass Cannot be Calibrated...1980
        DIAGNOSIS....1980
      INSPECTION PROCEDURE 4: There is a Discrepancy Between the Actual Outside Temperature and Display...1981
        DIAGNOSIS....1981
          STEP 1. Check the outside thermo sensor internal resistance...1981
          STEP 2. Check harness connector A-22 at the outside thermo sensor for loose, corroded or damaged ...1981
          STEP 3. Measure the outside thermo sensor voltage...1982
          STEP 4. Check harness connector E-59 at the inside rear view mirror (with compass and temperature...1982
          STEP 5. Check the harness wires between outside thermo sensor connector A-22 (terminal No.1 and 2...1983
          STEP 6. Retest the system...1984
    ON-VEHICLE SERVICE....1984
      PROCEDURES FOR CALIBRATING THE COMPASS....1984
      PROCESSES FOR ADJUSTING THE COMPASS VARIANCE....1985
      AUTO-DIMMING FEATURE TEST....1986
    SPECIAL TOOLS....1987
    INSTRUMENT PANEL ASSEMBLY....1989
    FLOOR CONSOLE ASSEMBLY....1992
    TRIMS....1993
    HEADLINING....1994
    INSIDE REAR VIEW MIRROR....1995
      REMOVAL SERVICE POINT....1995
    FRONT SEAT ASSEMBLY....1996
      INSTALLATION SERVICE POINT....1997
      INSPECTION....1997
    REAR SEAT ASSEMBLY....2001
    FRONT SEAT BELT....2004
      INSPECTION....2005
    REAR SEAT BELT....2006
    SPECIFICATIONS....2007
GR00004700-52....2009
  INTERIOR AND SUPPLEMENTAL RESTRAINT SYSTEM(SRS)....2009
GR00004800-54....2011
  CHASSIS ELECTRICAL....2011
    BATTERY....2015
      ON-VEHICLE SERVICE....2015
      BATTERY CHECK....2015
        BATTERY VISUAL INSPECTION (1)....2015
        BATTERY VISUAL INSPECTION (2)....2016
          STEP 1. Check the battery cables...2017
          STEP 2. Check the battery post...2017
          STEP 3. Check the battery case and cover...2017
          STEP 4. Check the open circuit voltage...2017
          STEP 5. Check the load test...2017
    IGNITION SWITCH....2018
      GENERAL DESCRIPTION....2018
      EQUIPMENT DIAGNOSIS....2018
        INTRODUCTION TO IGNITION SWITCH DIAGNOSIS....2018
      DIAGNOSIS FUNCTION....2019
        HOW TO CONNECT SCAN TOOL (MUT-III)....2019
      SYMPTOM PROCEDURES....2021
      INSPECTION PROCEDURE 1: When the Driver's Side Door is Opened, the Ignition Key Hole Illumination...2021
        STEP 1. Check the input signal (by using pulse check)...2023
        STEP 2. Check the input signal from the driver's side door switch (by using a voltmeter)...2024
        STEP 3. Check the driver's side door switch...2024
        STEP 4. Check the driver's side door switch ground circuit....2024
        STEP 5. Check driver's side door switch connector E-33 for loose, corroded or damaged terminals, ...2025
        STEP 6. Check the driver's side door switch connector E-33...2025
        STEP 7. Check the harness wires between driver's side door switch connector E-33 (terminal No.2) ...2026
        STEP 8. Check the ignition key hole illumination light input...2027
        STEP 9. Check the power supply for the ignition key hole illumination light...2028
        STEP 10. Check connector D-16 at the key reminder switch for damage...2028
        STEP 11. Check the harness wires between fusible link number 8 and key reminder switch connector ...2028
        STEP 12. Check the harness wires between key reminder switch connector D-16 (terminal No.2 and 6)...2029
        STEP 13. Check for continuity between terminals (except terminal No. 4 and No. 6) of key reminder...2030
        STEP 14. Recheck for malfunction...2030
      INSPECTION PROCEDURE 2: The Ignition Key Hole Illumination Light does not Go Out...2031
        STEP 1. Check the input signal (by using pulse check)...2031
        STEP 2. Check the input signal from the driver's side door switch (by using a voltmeter)...2032
        STEP 3. Check the driver's side door switch...2032
        STEP 4. Check the driver's side door switch ground circuit...2032
        STEP 5. Check the driver's side door switch connector E-33 input circuit....2033
        STEP 6. Check driver's side door switch connector E-33 for loose, corroded or damaged terminals, ...2033
        STEP 7. Check the harness wires between the driver's side door switch connector E-33 (terminal No...2034
        STEP 8. Recheck for malfunction...2035
      INSPECTION PROCEDURE 3: The Ignition Key Hole Illumination Light does not Go out when the Ignitio...2035
        STEP 1. Check the input signal (by using pulse check)...2036
        STEP 2. Check the input signal from the ignition switch (by using a voltmeter)...2036
        STEP 3. Check the ignition switch circuit...2037
        STEP 4. Check ETACS-ECU connector D-11 for loose, corroded or damaged terminals, or terminals pus...2037
        STEP 5. Check the harness wires between the ignition switch (IG1) and ETACS-ECU connector D-11 (t...2038
        STEP 6. Recheck for malfunction...2038
      INSPECTION PROCEDURE 4: The Ignition Key Reminder Tone Alarm does not Stop Sounding by Removing t...2039
        STEP 1. Check the input signal (by using pulse check)...2039
        STEP 2. Check the input signal from the ignition switch (by using a voltmeter)...2040
        STEP 3. Measure the continuity of the key reminder switch...2040
        STEP 4. Check the input signal from the key reminder switch...2040
        STEP 5. Check key reminder switch connector D-16 for loose, corroded or damaged terminals, or ter...2041
        STEP 6. Check the harness wire between key reminder switch connector D-16 and body ground...2041
        STEP 7. Check the harness wire between key reminder switch connector D-16 (terminal No.2 and 6) a...2042
        STEP 8. Check for continuity between terminals (except No. 4 and No. 6) of key reminder switch co...2043
        STEP 9. Recheck for malfunction...2043
      INSPECTION PROCEDURE 5: The Ignition Key Reminder Tone Alarm does not Sound when the Ignition Key...2043
        STEP 1. Check the input signal (by using pulse check)...2044
        STEP 2. Check the input signal from the driver's side door switch (by using a voltmeter)...2044
        STEP 3. Check the driver's side door switch...2045
        STEP 4. Check the driver's side door switch ground circuit...2045
        STEP 5. Check driver's side door switch connector E-33 input circuit...2045
        STEP 6. Check driver's side door switch connector E-33 for loose, corroded or damaged terminals, ...2046
        STEP 7. Check the harness wires between driver's side door switch connector E-33 and ETACS connec...2047
        STEP 8. Check for continuity of the key reminder switch...2048
        STEP 9. Check the input signal from the key reminder switch...2048
        STEP 10. Check key reminder switch connector D-16 for loose, corroded or damaged terminals, or te...2049
        STEP 11. Check the harness wire between key reminder switch connector D-16 (terminal No.4) and bo...2049
        STEP 12. Check the harness wire between key reminder switch connector D-16 (terminal No.2 and 6) ...2050
        STEP 13. Check for continuity between terminals (except No. 4 and No. 6) of key reminder switch c...2051
        STEP 14. Recheck for malfunction...2051
      EQUIPMENT DIAGNOSIS....2052
        INTRODUCTION TO IMMOBILIZER SYSTEM DIAGNOSIS....2052
      IMMOBILIZER SYSTEM TROUBLE CODE DIAGNOSIS....2053
        Retrieving and Erasing Immobilizer System Diagnostic Trouble Codes....2053
      DIAGNOSTIC TROUBLE CODE PROCEDURES....2054
      DTC: 11 Transponder Communication System or Radio Interference of Encrypted Code....2054
        STEP 1. Check that there is other key near the key in the ignition...2055
        STEP 2. Check that the engine starts using the spare ignition key which encrypted code has been r...2055
        STEP 3. Using scan tool MB991958, read the diagnostic trouble code...2055
        STEP 4. Check the ignition key ring antenna...2056
        STEP 5. Check immobilizer-ECU connector C-107 and ignition key ring antenna connector D-28 for lo...2056
        STEP 6. Check the harness wires between immobilizer-ECU connector C-107 (terminal No.10 and 11) a...2057
      DTC12: Encrypted Codes are not the Same or not Registered...2057
        STEP 1. Check that the encrypted code was registered...2057
      SYMPTOM PROCEDURES....2058
      INSPECTION PROCEDURE 1: Communication with Scan Tool MB991958 is Impossible...2058
        STEP 1. Using scan toll MB991958, read the MFI system diagnostic trouble code...2060
        STEP 2. Check the immobilizer-ECU power supply circuit by backprobing...2061
        STEP 3. Check immobilizer-ECU connector C-107 and engine control relay connector C-59 for loose, ...2061
        STEP 4. Check the harness wires between immobilizer-ECU connector C-107 (terminal No. 7) and MFI ...2062
        STEP 5. Check the immobilizer-ECU ground circuit by backprobing...2063
        STEP 6. Check immobilizer-ECU connector C-107 for loose, corroded or damaged terminals, or termin...2063
        STEP 7. Check the harness wire between immobilizer-ECU connector C-107 (terminal No.3) and ground...2063
        STEP 8. Check the harness wires between immobilizer-ECU connector C-107 (terminal No.5) and power...2064
        STEP 9. Replace the immobilizer-ECU or powertrain control module...2064
        STEP 10. Recheck for malfunction...2065
      INSPECTION PROCEDURE 2: Registering the Ignition Key is Impossible...2065
        STEP 1. Using scan tool MB991958, read the diagnostic trouble code...2066
        STEP 2. Recheck for malfunction...2066
      INSPECTION PROCEDURE 3: The "IMMOBILIZER" Indicator Light does not Illuminate...2067
        STEP 1. Check the "IMMOBILIZER" indicator light circuit of immobilizer-ECU connector C-107...2068
        STEP 2. Check the "IMMOBILIZER" indicator light...2068
        STEP 3. Check combination meter connector C-05 for loose, corroded or damaged terminals, or termi...2069
        STEP 4. Check the harness wires between immobilizer-ECU connector C-107 and combination meter con...2070
        STEP 5. Recheck for malfunction...2070
      INSPECTION PROCEDURE 4: Engine does not Start (Cranking but no Initial Combustion)...2071
        STEP 1. Check the battery positive voltage...2071
        STEP 2. Using scan tool MB991958, read the any diagnostic trouble code...2071
        STEP 3. Check the starting system...2072
        STEP 4. Recheck for malfunction...2072
      ON-VEHICLE SERVICE....2075
      ENCRYPTED CODE REGISTRATION METHOD....2075
        POINTS TO NOTE DURING OPERATION....2075
        KEY ID REGISTER....2076
      TRANSPONDER LOCK CHECK....2079
      IGNITION SWITCH....2082
        REMOVAL SERVICE POINTS....2083
        INSTALLATION SERVICE POINT....2083
      INSPECTION....2084
        IGNITION SWITCH CONTINUITY CHECK....2084
        KEY REMINDER SWITCH CHECK....2084
        IGNITION KEY RING ANTENNA CHECK....2084
    COMBINATION METER ASSEMBLY AND VEHICLE SPEED SENSOR....2085
      EQUIPMENT DIAGNOSIS....2085
      DIAGNOSIS FUNCTION....2085
        HOW TO CONNECT SCAN TOOL (MUT-III)....2085
      SYMPTOM PROCEDURES....2087
      INSPECTION PROCEDURE 1: Speedometer does not Work...2087
        STEP 1. Using scan tool MB991958, read the MFI system diagnostic trouble code...2089
        STEP 2. Check the odometer and trip odometer operation...2089
        STEP 3. Check the combination meter power supply circuit at the combination meter connector C-04...2090
        STEP 4. Check combination meter connector C-04 for loose, corroded or damaged terminals, or termi...2090
        STEP 5. Check the harness wires between combination meter connector C-04 (terminal No.24) and ign...2090
        STEP 6. Check the combination meter (speedometer) ground circuit at the combination meter connect...2091
        STEP 7. Check combination meter connector C-04 for loose, corroded or damaged terminals, or termi...2092
        STEP 8. Check the harness wire between combination meter connector C-04 (terminal No.31) and ground...2092
        STEP 9. Check the combination meter power supply circuit at combination meter connector C-02...2092
        STEP 10. Check combination meter connector C-02 for loose, corroded or damaged terminals, or term...2093
        STEP 11. Check the harness wires between combination meter connector C-02 (terminal No.53) and fu...2093
        STEP 12. Check the combination meter vehicle speed sensor input signal circuit at combination met...2095
        STEP 13. Check combination meter connector C-02 for loose, corroded or damaged terminals, or term...2096
        STEP 14. Check the harness wires between combination meter connector C-02 and vehicle speed senso...2096
        STEP 15. Measure the voltage at the vehicle speed sensor power supply circuit...2097
        STEP 16. Check vehicle speed sensor connector B-09 for loose, corroded or damaged terminals, or t...2098
        STEP 17. Check the harness wires between vehicle speed sensor connector B-09 (terminal No.1) and ...2098
        STEP 18. Check the resistance at the vehicle speed sensor ground circuit...2100
        STEP 19. Check vehicle speed sensor connector B-09 for loose, corroded or damaged terminals, or t...2101
        STEP 20. Check the harness wire between vehicle speed sensor connector B-09 (terminal No.2) and g...2101
        STEP 21. Check the vehicle speed sensor input signal circuit at the vehicle speed sensor connecto...2102
        STEP 22. Recheck for malfunction...2102
      INSPECTION PROCEDURE 2: Tachometer does not Work...2103
        STEP 1. Using scan tool MB991958, read the MFI system diagnostic trouble code...2105
        STEP 2. Check the speedometer operation...2105
        STEP 3. Check the combination meter (tachometer) ground circuit at combination meter connector C-05...2106
        STEP 4. Check combination meter connector C-05 for loose, corroded or damaged terminals, or termi...2107
        STEP 5. Check the harness wires between combination meter connector C-05 (terminal No.14) and gro...2107
        STEP 6. Check the ignition signal input circuit at combination meter connector C-04...2108
        STEP 7. Check combination meter connector C-04 for loose, corroded or damaged terminals, or termi...2108
        STEP 8. Check the harness wires between combination meter connector C-04 (terminal No.24) and ign...2108
        STEP 9. Check the circuit at ignition power transistor connector A-05...2109
        STEP 10. Check ignition power transistor connector A-05 for loose, corroded or damaged terminals,...2110
        STEP 11. Check ignition power transistor connector A-05 and combination meter connector C-05 for ...2110
        STEP 12. Check the harness wire between combination meter connector C-05 (terminal No.14) and ign...2111
      INSPECTION PROCEDURE 3: Fuel Gauge does not Work...2113
        STEP 1. Check the speedometer operation...2114
        STEP 2. Check the fuel level sensor signal circuit at fuel level sensor connector E-30...2115
        STEP 3. Check fuel level sensor connector E-30 and combination meter connector C-02 for loose, co...2115
        STEP 4. Check the harness wires between fuel level sensor connector E-30 (terminal No.2) and comb...2116
        STEP 5. Check the fuel level sensor ground circuit at fuel level sensor connector E-30...2117
        STEP 6. Check the fuel level sensor connector E-30 for loose, corroded or damaged terminals, or t...2117
        STEP 7. Check the harness wire between fuel level sensor connector E-30 (terminal No.3) and ground...2117
        STEP 8. Check the fuel level sensor...2118
      INSPECTION PROCEDURE 4: Engine Coolant Temperature Gauge does not Work...2119
        STEP 1. Check the speedometer operation...2121
        STEP 2. Check the engine coolant temperature sensor signal circuit at the engine coolant temperat...2121
        STEP 3. Check engine coolant temperature sensor connector A-08 (terminal No.1) and combination me...2122
        STEP 4. Check the harness wires between engine coolant temperature sensor connector A-08 (termina...2123
        STEP 5. Measure the engine coolant temperature gauge unit...2124
      ON-VEHICLE SERVICE....2126
      SPEEDOMETER CHECK....2126
      TACHOMETER CHECK....2127
      FUEL LEVEL SENSOR CHECK....2127
        Fuel Level Sensor Resistance....2127
        Fuel Level Sensor Float Height....2128
      ENGINE COOLANT TEMPERATURE GAUGE UNIT CHECK....2128
      COMBINATION METER ASSEMBLY....2129
      INSPECTION....2129
        FUEL GAUGE RESISTANCE CHECK....2129
        ENGINE COOLANT TEMPERATURE GAUGE RESISTANCE CHECK....2130
        VEHICLE SPEED SENSOR CHECK....2130
    AMBIENT TEMPERATURE SENSOR....2132
    HEADLIGHT....2133
      INSPECTION....2133
        AMBIENT TEMPERATURE SENSOR CHECK....2133
      LIGHTING SYSTEM DIAGNOSIS....2133
      SYMPTOM PROCEDURES....2134
      INSPECTION PROCEDURE 1: Light Reminder Tone Alarm Function does not Work Normally...2134
        STEP 1. Check the input signal (by using pulse check)...2137
        STEP 2. Check the input signal from the driver's side door switch (by using a voltmeter)...2137
        STEP 3. Check the driver's side door switch...2138
        STEP 4. Check the driver's side door switch ground circuit...2138
        STEP 5. Check driver's side door switch connector E-33 for loose, corroded or damaged terminals, ...2138
        STEP 6. Check driver's side door switch connector E-33 input circuit...2139
        STEP 7. Check the harness wires between driver's side door switch connector E-33 (terminal No.2) ...2140
        STEP 8. Check for continuity of the key reminder switch...2141
        STEP 9. Check the input signal from the key reminder switch...2141
        STEP 10. Check key reminder switch connector D-16 for damage for loose, corroded or damaged termi...2142
        STEP 11. Check the harness wire between key reminder switch connector D-16 (terminal No.4) and bo...2142
        STEP 12. Check the harness wire between key reminder switch connector D-16 (terminal No.6) and ET...2143
        STEP 13. Measure the voltage at the input signal from the ignition switch...2144
        STEP 14. Check ETACS-ECU connector D-11 for damage for loose, corroded or damaged terminals, or t...2144
        STEP 15. Check the harness wire between ETACS-ECU connector D-11 (terminal No.3) and ignition swi...2145
        STEP 16. Measure the voltage at the input signal from the fusible link number 8...2146
        STEP 17. Check harness wire between ETACS-ECU connector D-11 (terminal No.2) and fusible link num...2146
        STEP 18. Measure the voltage at the input signal from the column switch (lighting switch)...2147
        STEP 19. Check the harness wire between ETACS-ECU connector D-11 (terminal No.5) and column switch...2148
        STEP 20. Check for continuity between terminals (except No. 4 and No. 6) of key reminder switch c...2148
      INSPECTION PROCEDURE 2: Daytime Running Light Function does not Illuminate .<Vehicles for CANADA>....2149
        STEP 1. Check the daytime running light-ECU power supply (battery) circuit at daytime running lig...2151
        STEP 2. Check daytime running light-ECU connector A-96 for loose, corroded or damaged terminals, ...2151
        STEP 3. Check the harness wires between daytime running light-ECU connector A-96 (terminal No.1) ...2152
        STEP 4. Check the daytime running light-ECU power supply circuit (IG2) at the daytime running lig...2152
        STEP 5. Check the connector between daytime running light-ECU connector A-96 and ignition switch ...2153
        STEP 6. Check the harness wire between daytime running light-ECU connector A-96 (terminal No.2) a...2153
        STEP 7. Check the daytime running light ground circuit at daytime running light connector A-96...2154
        STEP 8. Check the daytime running light-ECU lighting switch input circuit at daytime running ligh...2155
        STEP 9. Check the connector between daytime running light-ECU connector A-96 and headlight relay ...2155
        STEP 10. Check the harness wire between daytime running light-ECU connector A-96 (terminal No.5) ...2156
        STEP 11. Check the daytime running light relay (lower) and (upper)...2156
        STEP 12. Check the connector between DRL relay (lower) connector A-97, DRL relay (upper) connecto...2157
        STEP 13. Check the harness wires between DRL relay (lower) connector A-97 (terminal No.1 and 2), ...2158
      ON-VEHICLE SERVICE....2159
      HEADLIGHT AIMING....2159
        PRE-AIMING INSTRUCTIONS....2159
        HEADLIGHT ADJUSTMENT....2160
      LUMINOUS INTENSITY MEASUREMENT....2160
      REPLACEMENT OF REPLACEABLE BULB....2161
      HEADLIGHT....2162
        REMOVAL SERVICE POINT....2163
      INSPECTION....2163
        LIGHTING SWITCH AND DIMMER/PASSING SWITCH CONTINUITY CHECK....2163
        TURN-SIGNAL LIGHT SWITCH CONTINUITY CHECK....2164
        HEADLIGHT RELAY CHECK....2165
        DRL RELAY (LOWER AND UPPER) CHECK....2165
    FOG LIGHT....2166
      LIGHTING SYSTEM DIAGNOSIS....2166
      ON-VEHICLE SERVICE....2166
      FOG LIGHT AIMING....2166
        PRE-AIMING INSTRUCTIONS....2166
        FOG LIGHT ADJUSTMENT....2167
      BULB REPLACEMENT....2167
      FOG LIGHT....2168
      INSPECTION....2169
        FOG LIGHT SWITCH CONTINUITY CHECK....2169
        FOG LIGHT RELAY CHECK....2169
    REAR COMBINATION LIGHT....2170
      REAR COMBINATION LIGHT....2170
    DOME LIGHT....2171
      LIGHTING SYSTEM DIAGNOSIS....2171
      SYMPTOM PROCEDURES....2172
      INSPECTION PROCEDURE 1: The Dome Light and Cargo Space Light does not Illuminate...2172
        STEP 1. Check the trouble symptom...2174
        STEP 2. Check dome light connector E-20 <vehicles with sunroof> or E-21 <vehicles without sunroof...2174
        STEP 3. Check the harness wires between dome light connector E-20 (terminal No.2) <vehicles with ...2175
        STEP 4. Check the dome light bulb or cargo space light bulb...2176
        STEP 5. Check the dome light and cargo space light power supply circuit at dome light connector E...2177
        STEP 6. Check dome light connector E-20 <vehicles with sunroof> or E-21 <vehicles without sunroof...2178
        STEP 7. Check the harness wires between dome light connector E-20 (terminal No.1) <vehicles with ...2179
        STEP 8. Recheck for malfunction...2180
      INSPECTION PROCEDURE 2: Dome Light and Cargo Space Light Dimming Function does not Work Normally...2181
        DIAGNOSIS....2181
          STEP 1. Check the ETACS-ECU power supply circuit...2181
          STEP 2. Check the input signal (by using pulse check)...2182
          STEP 3. Check the input signal (by using a voltmeter)...2182
    HIGH-MOUNTED STOPLIGHT....2183
    RHEOSTAT....2184
      INSPECTION....2184
        RHEOSTAT CHECK....2184
    HAZARD WARNING LIGHT SWITCH....2185
      INSPECTION....2185
        HAZARD WARNING LIGHT SWITCH CONTINUITY CHECK....2185
    HORN....2186
      HORN....2186
      INSPECTION....2187
        HORN RELAY CONTINUITY CHECK....2187
        THEFT-ALARM HORN RELAY CONTINUITY CHECK....2187
    CIGARETTE LIGHTER....2188
      INSPECTION....2188
        CIGARETTE LIGHTER CHECK....2188
    ACCESSORY SOCKET....2189
      INSPECTION....2190
        ACCESSORY SOCKET RELAY CONTINUITY CHECK....2190
    RADIO AND TAPE PLAYER....2190
      RADIO WITH TAPE PLAYER AND CD PLAYER, SPEAKER AND ANTENNA DIAGNOSIS....2190
      SYMPTOM PROCEDURES....2192
      INSPECTION PROCEDURE 1: When Power Switch is Turned "ON," No Power is Available...2192
        STEP 1. Check the radio and CD player power supply circuit by backprobing...2194
        STEP 2. Check radio and CD player connector C-62 for damage...2194
        STEP 3. Check the harness wires between radio and CD player connector C-62 (terminal No.10) and i...2195
        STEP 4. Check that the radio and CD player are installed correctly...2196
        STEP 5. Recheck for malfunction...2196
      INSPECTION PROCEDURE 2: No Sound. <Vehicles with Amplifier>....2197
        STEP 1. Measure the voltage at the amplifier power supply circuit...2199
        STEP 2. Check amplifier connector E-11 for loose, corroded or damaged terminals, or terminals pus...2199
        STEP 3. Check the harness wires between amplifier connector E-11 (terminal No.2 and No.10) and fu...2200
        STEP 4. Check amplifier connector E-11 for loose, corroded or damaged terminals, or terminals pus...2202
        STEP 5. Check the harness wires between amplifier connector E-11 (terminal No.1 and No.9) and gro...2202
        STEP 6. Check the DIN cable between amplifier and radio, tape player and CD Player...2202
        STEP 7. Recheck for malfunction...2202
      INSPECTION PROCEDURE 3: No Sound from One Speaker...2203
        STEP 1A. Check which speaker has no sound on the vehicles without amplifier...2207
        STEP 1B. Check which speaker has no sound on the vehicles with amplifier...2207
        STEP 2. Check the speaker...2207
        STEP 3. Check tweeter (LH) connector F-03 and/or front door speaker (LH) connector F-13 for loose...2208
        STEP 4. Check the harness wires between radio and CD player connector C-62 (terminal No.5 and 13)...2208
        STEP 5. Check the radio and CD player connector C-62 for loose, corroded or damaged terminals, or...2209
        STEP 6. Recheck for malfunction...2209
        STEP 7. Check the speaker...2209
        STEP 8. Check tweeter (RH) connector F-16 and/or front door speaker (RH) connector F-25 for loose...2210
        STEP 9. Check the harness wires between radio and CD player connector C-62 (terminal No.6 and 14)...2210
        STEP 10. Check radio and CD player connector C-62 for loose, corroded or damaged terminals, or te...2211
        STEP 11. Recheck for malfunction...2211
        STEP 12. Check the speaker...2211
        STEP 13. Check rear door speaker (LH) connector F-10 for loose, corroded or damaged terminals, or...2212
        STEP 14. Check the harness wires between radio and CD player connector C-62 (terminal No.2 and 8)...2212
        STEP 15. Check radio and CD player connector C-62 for loose, corroded or damaged terminals, or te...2213
        STEP 16. Recheck for malfunction...2213
        STEP 17. Check the rear door speaker (RH)...2214
        STEP 18. Check rear door speaker (RH) connector F-22 for loose, corroded or damaged terminals, or...2214
        STEP 19. Check the harness wires between radio and CD player connector C-62 (terminal No.1 and 7)...2214
        STEP 20. Check radio and CD player connector C-62 for loose, corroded or damaged terminals, or te...2215
        STEP 21. Recheck for malfunction...2215
        STEP 22. Check the Front speaker (LH) and /or tweeter (LH)...2216
        STEP 23. Check tweeter (LH) connector F-03 and/or front speaker (LH) connector C-36 for loose, co...2216
        STEP 24. Check the harness wires between amplifier connector E-11 (terminal No.13 and14) and twee...2217
        STEP 25. Check amplifier connector E-11 for loose, corroded or damaged terminals, or terminals pu...2218
        STEP 26. Recheck for malfunction...2219
        STEP 27. Check the front door speaker (RH) and /or tweeter (RH)...2219
        STEP 28. Check tweeter (RH) connector F-16 and/or front speaker (RH) connector C-20 for loose, co...2219
        STEP 29. Check the harness wires between amplifier connector E-11 (terminal No.3 and 4) and tweet...2220
        STEP 30. Check amplifier connector E-11 for loose, corroded or damaged terminals, or terminals pu...2221
        STEP 31. Recheck for malfunction...2222
        STEP 32. Check the front door speaker (LH)...2222
        STEP 33. Check front door speaker (LH) connector F-13 for loose, corroded or damaged terminals, o...2222
        STEP 34. Check the harness wires between amplifier connector E-11 (terminal No.5 and 6) and front...2223
        STEP 35. Check amplifier connector E-11 for loose, corroded or damaged terminals, or terminals pu...2224
        STEP 36. Recheck for malfunction...2224
        STEP 37. Check the front door speaker (RH)...2224
        STEP 38. Check front door speaker (RH) connector F-25 for loose, corroded or damaged terminals, o...2224
        STEP 39. Check the harness wires between amplifier connector E-11 (terminal No.15 and 16) and fro...2225
        STEP 40. Check amplifier connector E-11 for loose, corroded or damaged terminals, or terminals pu...2226
        STEP 41. Recheck for malfunction...2226
        STEP 42. Check the rear door speaker (LH)...2226
        STEP 43. Check rear door speaker (LH) connector F-10 for loose, corroded or damaged terminals, or...2226
        STEP 44. Check the harness wires between amplifier connector E-11 (terminal No.17 and 18) and rea...2227
        STEP 45. Check amplifier connector E-11 for loose, corroded or damaged terminals, or terminals pu...2227
        STEP 46. Recheck for malfunction...2228
        STEP 47. Check the rear door speaker (RH)...2228
        STEP 48. Check rear door speaker (RH) connector F-22 for loose, corroded or damaged terminals, or...2228
        STEP 49. Check the harness wires between amplifier connector E-11 (terminal No.7 and 8) and rear ...2229
        STEP 50. Check amplifier connector E-11 for loose, corroded or damaged terminals, or terminals pu...2230
        STEP 51. Recheck for malfunction...2230
      INSPECTION PROCEDURE 4: Noise Appears at Certain Places when Traveling (AM)...2230
        STEP 1. Check that the noise occur when entering or near a particular structure (building, tunnel...2230
        STEP 2. After taking the following measures to prevent the noise, check that no noise appears...2230
        STEP 3. Ask the owner about the state of the noise...2230
        STEP 4. Check that there is no noise...2230
      INSPECTION PROCEDURE 5: Noise Appears at Certain Places when Traveling (FM)...2231
      INSPECTION PROCEDURE 6: Mixed with Noise, Only at Night (AM)...2232
        STEP 1. Check that the noise is still obvious even when the lights are off...2232
        STEP 2. Check that the following actions disappear the noise...2232
        STEP 3. Check that the noise fades away when the vehicle harness is moved away from the radio (if...2232
      INSPECTION PROCEDURE 7: Broadcasts can be Heard but Both AM and FM Have a Lot of Noise...2232
        STEP 1. Check that the noise occurs when the engine is stopped or the engine is running...2232
        STEP 2. Check that the following actions disappear the noise...2232
        STEP 3. Check that the radio is correctly grounded...2232
        STEP 4. Check that the antenna plug is properly connected to the radio...2233
        STEP 5. Check that the noise is eliminated when the antenna plug is properly attached...2233
        STEP 6. Check that the antenna is in good condition and is properly mounted...2233
        STEP 7. Clean the antenna plug and ground wire mounting area. Mount the antenna securely. On a ve...2233
      INSPECTION PROCEDURE 8: There is More Noise on either AM or FM...2234
        STEP 1. Check that there is noise under the following state(s)...2234
        STEP 2. Continue to check for static; when static is detected, check for the conditions listed ab...2234
        STEP 3. Check noise prevention on the radio side is difficult...2234
      INSPECTION PROCEDURE 9: There is Noise when Starting the Engine...2235
      INSPECTION PROCEDURE 10: Some Noise Appears when there is Vibration or Shocks during Traveling...2237
        STEP 1. Check that the connectors are properly connected...2237
        STEP 2. Check that noise appears when the radio switch is turned on while the vehicle is stopped...2237
        STEP 3. Check that the radio is correctly grounded...2237
        STEP 4. Check that the antenna is correctly grounded. (If noise appears when the antenna is moved...2237
      INSPECTION PROCEDURE 11: Noise Sometimes Appears on FM during Traveling...2237
        STEP 1. Retune the radio, and check that there is no noise...2237
        STEP 2. Check that the noise appears only in certain locations and only with certain stations...2237
        STEP 3. Check that the connectors are properly connected...2238
        STEP 4. Check that noise appears when the radio switch is turned on while the vehicle is stopped...2238
        STEP 5. Check that the radio is correctly grounded...2238
        STEP 6. Check that the antenna is correctly grounded. (If noise appears when the antenna is moved...2238
      INSPECTION PROCEDURE 12: Ever-present Noise...2238
      INSPECTION PROCEDURE 13: There is Noise but No Reception for Both AM and FM or No Sound from AM, ...2239
        STEP 1. Make sure that the check is being conducted under special electrical field conditions...2239
        STEP 2. Check that proper performance is obtained when the vehicle is moved...2239
        STEP 3. Check that tuning solves the problem...2239
        STEP 4. Check that the antenna plug and radio unit are properly connected...2239
        STEP 5. Check that the problem disappear if another radio is used...2239
      INSPECTION PROCEDURE 14: Poor Reception...2239
        STEP 1. Make sure that the check is being conducted under special electrical field conditions...2239
        STEP 2. Check that proper performance is obtained when the vehicle is moved...2239
        STEP 3. Check that tuning solves the problem...2239
        STEP 4. Check that the problem is limited to the reception of a specific radio station from a spe...2240
        STEP 5. Check that the antenna plug is connected to the radio properly...2240
        STEP 6. Check that the problem disappears when another radio is used...2240
      INSPECTION PROCEDURE 15: Distortion on AM or on Both AM and FM...2240
        STEP 1. Check how much distortion there is...2240
        STEP 2. Check that there is distortion near the radio station...2240
        STEP 3. Check that the speaker cords are in contact with the cone paper...2240
        STEP 4. Remove the speakers, and check for torn cone paper or foreign material...2240
        STEP 5. Check for distortion with the speaker installed...2240
      INSPECTION PROCEDURE 16: Distortion on FM Only...2241
        STEP 1. Check that the distortion persists when the radio is turned to another station...2241
        STEP 2. Check that the distortion increases or decreases when the vehicle is moved...2241
      INSPECTION PROCEDURE 17: Using the Auto Select Function, too Few Automatic Stations are Selected...2241
        STEP 1. Consider the number of radio stations. Check that there are enough in the area...2241
        STEP 2. Consider the distance to the radio stations. Check that the transmitting antennas are wit...2241
        STEP 3. Make sure that the check is being conducted under special field conditions...2241
        STEP 4. Check that proper performance is obtained when the vehicle is moved...2241
        STEP 5. Check that the antenna plug is connected to the radio properly...2241
        STEP 6. Check that the problem disappears when another radio is used...2241
      INSPECTION PROCEDURE 18: Preset Station are Erased...2242
        STEP 1. Check the radio, tape player and CD player memory backup power supply circuit...2243
        STEP 2. Check harness connector C-62 at the radio, tape player and CD player for loose, corroded ...2243
        STEP 3. Check the harness wires between radio, tape player, CD player connector C-62 (terminal No...2244
        STEP 4. Recheck for malfunction...2245
      INSPECTION PROCEDURE 19: CD can not be Inserted...2245
        STEP 1. Check that the shutter opens when a CD is inserted...2245
        STEP 2. Check that the CD is ejected from approximately 15 mm (0.6 inch) inside the insertion pan...2245
        STEP 3. Check that "E" (error) is displayed even though the CD is inserted completely...2245
        STEP 4A. Check the CD...2245
        STEP 4B. Check the CD...2245
        STEP 4C. Check the CD...2245
      INSPECTION PROCEDURE 20: No sound. (CD only)....2246
        STEP 1. Check that the CD player plays properly if another CD is inserted...2246
        STEP 2. Return it to the normal temperature, and recheck the operation. Check that the CD player ...2246
      INSPECTION PROCEDURE 21: CD Sound Skips...2246
        STEP 1. Malfunction occurrence state...2246
        STEP 2. Check that the CD face scratched or dirty...2246
        STEP 3. Check that the CD player plays properly if another CD is started...2246
        STEP 4. Check that sound skips when the side of the CD player is tapped...2246
      INSPECTION PROCEDURE 22: Sound Quality is Poor...2247
        STEP 1. Check that the CD player plays properly if another CD is inserted...2247
      INSPECTION PROCEDURE 23: CD can not be Ejected...2247
        STEP 1. Check that the key switch (ignition key) is at "ACC" or "ON"...2247
        STEP 2. Check that the combined amplifier or radio set connected securely?....2247
      INSPECTION PROCEDURE 24: Motor Antenna won't Extend or Retract...2248
        STEP 1. Clean and polish the surface of the antenna pole, and then check the trouble symptom...2249
        STEP 2. Clean the antenna...2250
        STEP 3. Check the motor antenna's motor...2250
        STEP 4. Check the antenna motor-ECU...2250
        STEP 5. Measure the voltage at motor antenna power supply circuit (motor antenna extension side)...2251
        STEP 6. Measure the voltage at motor antenna power supply circuit (motor antenna retraction side)...2251
        STEP 7. Check harness connector C-19 at the motor antenna for loose, corroded or damaged terminal...2251
        STEP 8. Check the harness wires between motor antenna connector C-19 (terminal No. 1 and 2) and a...2252
        STEP 9. Check antenna motor-ECU connector C-34 for loose, corroded or damaged terminals, or termi...2253
        STEP 10. Check the harness wires between antenna motor-ECU connector C-34 (terminal No. 6) and ra...2253
        STEP 11. Measure the voltage at the antenna motor-ECU power supply circuit. (Fusible link number 8)....2254
        STEP 12. Check the harness wires between fusible link number 8 and antenna motor-ECU connector C-...2254
        STEP 13. Measure the voltage at the antenna motor-ECU power supply circuit. (Ignition switch "ACC")....2256
        STEP 14. Check the harness wires between ignition switch "ACC" and antenna motor-ECU connector C-...2256
        STEP 15. Measure the voltage at the antenna motor-ECU power supply circuit. [Ignition switch "ON"...2258
        STEP 16. Check the harness wires between ignition switch "ON" and antenna motor-ECU connector C-3...2258
        STEP 17. Recheck for malfunction...2259
      INSPECTION PROCEDURE 25: Motor Antenna Extends and Retracts but does not Receive Radio Signal...2260
        STEP 1. Is the antenna normal?....2260
        STEP 2. Check the motor antenna...2260
      ON-VEHICLE SERVICE....2261
      PROCEDURE FOR INPUT OF SECURITY CODE FOR ANTI-THEFT SYSTEM....2261
        Three-minute operation mode....2263
      SPEAKER TEST....2263
      RADIO WITH CD PLAYER....2264
    SPEAKER....2265
    AMPLIFIER....2266
    ANTENNA....2267
      REMOVAL SERVICE POINT....2269
      INSPECTION....2269
        MOTOR ANTENNA CHECK....2269
        ANTENNA MOTOR-ECU CHECK....2269
        GLASS ANTENNA CHECK....2270
      ANTENNA POLE REPLACEMENT....2270
    REAR WINDOW DEFOGGER....2271
      ON-VEHICLE SERVICE....2271
      PRINTED-HEATER LINES CHECK....2271
      REAR WINDOW DEFOGGER SWITCH....2272
      INSPECTION....2272
        REAR WINDOW DEFOGGER SWITCH CONTINUITY CHECK....2272
        REAR WINDOW DEFOGGER RELAY CONTINUITY CHECK....2273
    THEFT ALARM....2274
      THEFT-ALARM SYSTEM DIAGNOSIS....2274
        Theft-alarm system....2274
        Panic Alarm Function....2274
      SYMPTOM PROCEDURES....2275
      INSPECTION PROCEDURE 1: Theft-alarm System is not Armed (Security Indicator Light does not Illumi...2275
        STEP 1. Check the ETACS-ECU power supply circuit...2277
        STEP 2. Check the security indicator circuit at the ETACS-ECU connector D-26...2277
        STEP 3. Check the security indicator light bulb...2278
        STEP 4. Check security indicator connector C-108 and ETACS-ECU connector D-26 for loose, corroded...2278
        STEP 5. Check the harness wire between security indicator connector C-108 and ETACS-ECU connector...2279
        STEP 6. Check the harness wire between security indicator connector C-108 (terminal No.2) and fus...2279
        STEP 7. Check the input signal (by using pulse check)...2281
        STEP 8. Check the input signal (by using a voltmeter)...2281
      INSPECTION PROCEDURE 2: Horn does not Sound when the Theft-alarm is Triggered...2282
        STEP 1. Check the keyless entry system horn answerback...2284
        STEP 2. Check the theft-alarm horn...2284
        STEP 3. Check the theft-alarm horn relay...2284
        STEP 4. Measure the theft-alarm horn relay power supply voltage at the theft-alarm horn relay con...2285
        STEP 5. Check theft-alarm horn relay connector C-100 for loose, corroded or damaged terminals, or...2285
        STEP 6. Check the harness wires between theft-alarm horn relay connector C-100 (terminal No.2) an...2285
        STEP 7. Check theft-alarm horn relay connector C-100 and ETACS-ECU connector D-26 for loose, corr...2286
        STEP 8. Check the harness wires between theft-alarm horn relay connector C-100 (terminal No.4) an...2287
        STEP 9. Check theft-alarm horn relay connector C-100 and theft-alarm horn connector A-91 for loos...2288
        STEP 10. Check the harness wire between theft-alarm horn relay connector C-100 (terminal No.3) an...2288
        STEP 11. Check that the theft-alarm horn is installed properly...2289
        STEP 12. Recheck for malfunction...2289
      INSPECTION PROCEDURE 3: Headlights do not Flash when the Theft-alarm System is Triggered...2290
        STEP 1. Check the headlight operation...2291
        STEP 2. Check the ETACS-ECU...2291
        STEP 3. Check the harness wires between joint connector C-70 (terminal No.26) and ETACS-ECU conne...2292
        STEP 4. Recheck for malfunction...2293
      INSPECTION PROCEDURE 4: Panic Alarm Function does not Work...2293
        STEP 1. Check the keyless entry system...2293
        STEP 2. Check the input signal (by using pulse check)...2294
        STEP 3. Check the input signal (by using a voltmeter)...2294
      INSPECTION PROCEDURE 5: Scan Tool MB991958 Communication is not Possible...2295
        STEP 1. Using scan tool MB991958, read the other systems diagnostic trouble code...2297
        STEP 2. Check the ignition switch positions...2298
        STEP 3. Check data link connector C-69 and ETACS-ECU connector D-27 for loose, corroded or damage...2299
        STEP 4. Check the harness wires between data link connector C-69 (terminal No.1 and 9) and ETACS-...2300
        STEP 5. Measure the resistance at the ETACS-ECU ground circuit...2301
        STEP 6. Check ETACS-ECU connector D-11 for loose, corroded or damaged terminals, or terminals pus...2302
        STEP 7. Check the harness wires between ETACS-ECU connector D-11 and ground...2302
        STEP 8. Recheck for malfunction...2303
      INSPECTION PROCEDURE 6: The Key Reminder Switch Signal is not Sent to the ETACS-ECU...2303
        STEP 1. Check the key reminder switch...2305
        STEP 2. Check key reminder switch connector D-16 and ETACS-ECU connector D-11 for loose, corroded...2305
        STEP 3. Check the harness wires between key reminder switch connector D-16 (terminal No.6) and ET...2306
        STEP 4. Check for continuity between terminals (except No. 4 and No. 6) of key reminder switch co...2307
        STEP 5. Recheck for malfunction...2307
      INSPECTION PROCEDURE 7: The Hood Switch is not Input...2308
        STEP 1. Check the hood switch...2309
        STEP 2. Check hood switch connector A-94 and ETACS-ECU connector D-26 for loose, corroded or dama...2310
        STEP 3. Check the harness wires between hood switch connector A-94 (terminal No.1) and ETACS-ECU ...2310
        STEP 4. Check the harness wires between hood switch connector A-94 (terminal No.2) and ground...2311
        STEP 5. Recheck for malfunction...2312
      INSPECTION PROCEDURE 8: Check the Circuit (Power Supply Line) from the Battery to the ETACS-ECU...2312
        STEP 1. Measure the voltage at ETACS-ECU power supply...2314
        STEP 2. Check ETACS-ECU connector D-11 for loose, corroded or damaged terminals, or terminals pus...2314
        STEP 3. Check the harness wires between ETACS-ECU connector D-11 (terminal No.2) and fusible link...2314
      THEFT ALARM....2316
      INSPECTION....2317
        SECURITY INDICATOR CONTINUITY CHECK....2317
    SPECIFICATIONS....2318
GR00004900-13B....2321
  FUEL SUPPLY....2321
    GENERAL DESCRIPTION....2322
    FUEL SUPPLY DIAGNOSIS....2322
      SYMPTOM PROCEDURES....2323
      INSPECTION PROCEDURE 1:Engine Malfunctions Due to Insufficient Fuel Supply....2323
        DIAGNOSIS....2323
          STEP 1. Using scan tool MB991958, read the diagnostic trouble code (DTC)...2323
          STEP 2. Check the fuel pressure...2324
          STEP 3. Check for bending, twisting or clogging of the fuel pipe or hose...2324
          STEP 4. Check the fuel filter operation...2324
          STEP 5. Check the fuel pump assembly operation...2324
          STEP 6. Check the inside of the fuel tank for contamination and rust...2324
          STEP 7. Retest the system...2324
    SPECIAL TOOLS....2325
    FUEL TANK....2326
      INSPECTION....2327
        FUEL SHUT-OFF VALVE CHECK....2327
        FUEL CUT-OFF VALVE CHECK....2327
        FUEL TANK DIFFERENTIAL PRESSURE SENSOR CHECK....2328
        FUEL GAUGE UNIT CHECK....2328
      FUEL FILTER REPLACEMENT....2328
    SPECIFICATIONS....2330
GR00005000-14....2331
  ENGINE COOLING....2331
    GENERAL DESCRIPTION....2332
    SPECIAL TOOL....2332
    ENGINE COOLING DIAGNOSIS....2332
      SYMPTOM PROCEDURES....2333
      INSPECTION PROCEDURE 1: Coolant Leak....2333
        DIAGNOSIS....2333
          STEP 1. Check for coolant leaks...2333
          STEP 2. Retest the system...2333
      INSPECTION PROCEDURE 2: Engine Overheating....2334
        DIAGNOSIS....2334
          STEP 1. Remove the radiator cap and check for coolant contamination...2334
          STEP 2. Check the radiator cap valve opening pressure...2334
          STEP 3. Check thermostat operation...2334
          STEP 4. Check the drive belt for slippage or damage...2334
          STEP 5. Retest the system...2334
    ON-VEHICLE SERVICE....2335
      ENGINE COOLANT LEAK CHECK....2335
      RADIATOR CAP PRESSURE CHECK....2335
      ENGINE COOLANT REPLACEMENT....2336
      ENGINE COOLANT CONCENTRATION TEST....2337
      DRIVE BELT TENSION CHECK AND ADJUSTMENT....2337
    RADIATOR....2338
      REMOVAL SERVICE POINTS....2338
      INSTALLATION SERVICE POINT....2339
    COOLING FAN....2339
      INSPECTION....2340
        Cooling Fan Check....2340
        Fan Clutch Check....2340
    THERMOSTAT....2340
      INSTALLATION SERVICE POINT....2341
      INSPECTION....2341
        Thermostat Check....2341
    WATER PUMP....2342
      REMOVAL SERVICE POINT....2343
      INSTALLATION SERVICE POINTS....2343
    WATER HOSE AND WATER PIPE....2345
      REMOVAL SERVICE POINT....2346
      INSTALLATION SERVICE POINTS....2346
      INSPECTION....2347
        Water Pipe and Hose Check....2347
    SPECIFICATIONS....2347
GR00005100-15....2349
  INTAKE AND EXHAUST....2349
    GENERAL DESCRIPTION....2350
    INTAKE AND EXHAUST DIAGNOSIS....2350
      SYMPTOM PROCEDURES....2350
      INSPECTION PROCEDURE 1: Exhaust Leakage....2350
        DIAGNOSIS....2350
          STEP 1. Start the engine. Have an assistant stay ....2350
          STEP 2. Check the gasket for cracks, damage...2350
          STEP 3. Check for loosening in each coupling section...2350
      INSPECTION PROCEDURE 2: Abnormal Noise....2351
        STEP 1. Start the engine. Have an assistant stay ....2351
        STEP 2. Check for missing parts in the muffler. Tap the muffler lightly to check for loose baffle...2351
        STEP 3. Check the hanger for cracks...2351
        STEP 4. Check for interference of the pipes and muffler with the body...2351
        STEP 5. Check the heat protectors...2351
        STEP 6. Check the pipes, catalytic converters and muffler for damage...2351
    SPECIAL TOOL....2351
    AIR CLEANER....2352
    INTAKE MANIFOLD....2353
      REMOVAL SERVICE POINT....2355
      INSTALLATION SERVICE POINTS....2355
      INSPECTION....2356
    EXHAUST MANIFOLD....2357
      INSPECTION....2357
    EXHAUST PIPE AND MAIN MUFFLER....2358
      REMOVAL SERVICE POINT....2358
      INSTALLATION SERVICE POINT....2359
    SPECIFICATIONS....2359
GR00005200-32....2361
  POWER PLANT MOUNT....2361
    GENERAL DESCRIPTION....2362
    ENGINE MOUNTING....2364
      INSTALLATION SERVICE POINT....2365
      INSPECTION....2365
    TRANSMISSION MOUNTING....2366
      INSPECTION....2367
    FRONT DIFFERENTIAL MOUNTING....2368
      INSPECTION....2368
    CROSSMEMBER....2369
      INSPECTION....2369
    SPECIFICATIONS....2370
GR00005300-55....2371
  HEATER, AIR CONDITIONING AND VENTILATION....2371
    GENERAL DESCRIPTION....2373
      SAFETY PRECAUTIONS....2373
      OPERATION....2374
    MANUAL A/C DIAGNOSIS....2375
      SYMPTOM PROCEDURES....2377
      INSPECTION PROCEDURE 1: When the Ignition Switch is ON, the A/C does not Operate...2377
        DIAGNOSIS....2377
          STEP 1. Check for refrigerant leaks...2377
          STEP 2. Check for excessive refrigerant...2377
          STEP 3. Check the A/C compressor clutch relay continuity...2377
          STEP 4. Check the A/C compressor clutch operation...2378
          STEP 5. Check the dual pressure switch operation...2378
          STEP 6. Check the A/C switch continuity...2378
          STEP 7. Check the blower switch continuity...2379
          STEP 8. Measure the automatic compressor controller terminal voltage...2379
          STEP 9. Measure the powertrain control module terminal voltage...2379
          STEP 10. Retest the system...2379
      INSPECTION PROCEDURE 2: When the Air Outlet Changeover Control Knob is Moved to Defroster or Defr...2380
        STEP 1. Check the defroster switch continuity...2380
        STEP 2. Check each A/C part...2380
      INSPECTION PROCEDURE 3: When The A/C is Operating, Temperature inside the Passenger Compartment d...2381
        DIAGNOSIS....2381
          STEP 1. Check for refrigerant leaks...2381
          STEP 2. Check the dual pressure switch operation...2381
          STEP 3. Measure the automatic compressor controller terminal voltage...2381
          STEP 4. Measure the powertrain control module terminal voltage...2381
          STEP 5. Retest the system...2382
      INSPECTION PROCEDURE 4: Blower Fan and Motor do not Operate...2382
        DIAGNOSIS....2382
          STEP 1. Check the blower relay continuity...2382
          STEP 2. Check the blower fan and motor operation...2382
          STEP 3. Check the blower switch continuity...2383
          STEP 4. Check the resistor resistance value...2383
          STEP 5. Retest the system...2383
      INSPECTION PROCEDURE 5: Blower Fan and Motor do not Stop Operating...2384
        DIAGNOSIS....2384
          STEP 1. Check the harness wires between the blower switch connector C-07 (terminal No.2, 3 and 6)...2384
          STEP 2. Check the blower relay continuity...2385
          STEP 3. Check the blower switch continuity...2385
          STEP 4. Retest the system...2386
      INSPECTION PROCEDURE 6: When the A/C is Operating, Condenser Fan do not Operate...2386
        DIAGNOSIS....2386
          STEP 1. Check the condensor fan control Relay continuity...2386
          STEP 2. Check the condenser fan motor operation...2387
          STEP 3. Measure the PCM terminal voltage...2387
          STEP 4. Retest the system...2387
      INSPECTION PROCEDURE 7: Even when the Rear Heater Switch is Pressed, the Blower Fan does not Turn...2388
        DIAGNOSIS....2388
          STEP 1. Check the rear heater relay continuity...2388
          STEP 2. Check the rear blower motor operation...2388
          STEP 3. Check the rear heater switch continuity...2389
          STEP 4. Check the resister resistance value...2389
          STEP 5. Retest the system...2389
      INSPECTION PROCEDURE 8: The Rear Heater Air Volume cannot be Controlled in Two Steps...2390
        DIAGNOSIS....2390
          STEP 1. Check the rear heater switch continuity...2390
          STEP 2. Check the resister resistance value...2390
          STEP 3. Retest the system...2390
      INSPACTION PROCEDURE 9: When the Heater Control Knob is Set to the "MAX COOL" Position, the Air-C...2391
        STEP 1. Check for refrigerant leaks...2391
        STEP 2. Check the water shut motor....2391
        STEP 3. Check the water shut valve controller continuity...2391
        STEP 4. Check symptoms...2392
      INSPACTION PROCEDURE 10: Warm Air does not Go Out From the Air Outlets....2393
        STEP 1. Check the water shut motor....2393
        STEP 2. Check the water shut valve controller continuity...2393
        STEP 3. Check symptoms...2394
    SPECIAL TOOLS....2396
    ON-VEHICLE SERVICE....2397
      REFRIGERANT LEVEL TEST....2397
      A/C COMPRESSOR CLUTCH TEST....2397
      RECEIVER DRIER TEST....2397
      DUAL PRESSURE SWITCH CHECK....2397
      COMPRESSOR DRIVE BELT ADJUSTMENT....2398
      CHARGING....2398
        METHOD BY USING REFRIGERANT RECOVERY AND RECYCLING UNIT....2398
        DISCHARGING SYSTEM....2398
        REFILLING OF OIL IN THE A/C SYSTEM....2398
      PERFORMANCE TEST....2399
        LOST CHARGE....2400
        LOW CHARGE....2400
        HANDLING TUBING AND FITTINGS....2400
      COMPRESSOR NOISE CHECK....2401
      POWER RELAY CHECK....2402
        BLOWER RELAY....2402
        A/C COMPRESSOR RELAY, CONDENSER FAN MOTOR RELAY....2402
        REAR HEATER RELAY....2403
      IDLE-UP OPERATION CHECK....2404
    HEATER CONTROL ASSEMBLY, A/C SWITCH AND INSIDE/OUTSIDE CHANGEOVER SWITCH....2405
      INSTALLATION SERVICE POINT....2405
      INSPECTION....2406
        A/C SWITCH CONTINUITY CHECK....2406
        INSIDE/OUTSIDE AIR DAMPER CONTROLLER CONTINUITY CHECK....2406
        INSIDE/OUTSIDE AIR CHANGEOVER SWITCH....2408
        BLOWER SWITCH CONTINUITY CHECK....2409
        MICRO SWITCH CONTINUITY CHECK....2409
    HEATER UNIT AND HEATER CORE....2410
      REMOVAL SERVICE POINT....2411
      INSTALLATION SERVICE POINT....2411
      INSPECTION....2411
        WATER SHUT MOTOR CHECK....2411
    BLOWER ASSEMBLY AND RESISTOR....2412
      INSPECTION....2413
        BLOWER FAN AND MOTOR CHECK....2413
        RESISTOR CHECK....2413
        INSIDE/OUTSIDE AIR CHANGEOVER DAMPER MOTOR CHECK....2413
    EVAPORATOR ASSEMBLY....2414
      REMOVAL SERVICE POINT....2414
      INSTALLATION SERVICE POINT....2414
    REAR HEATER UNIT....2416
      INSPECTION....2417
        REAR HEATER SWITCH CONTINUITY CHECK....2417
        REAR BLOWER MOTOR OPERATION CHECK....2417
        RESISTER CHECK....2417
    COMPRESSOR ASSEMBLY....2418
      REMOVAL SERVICE POINTS....2419
      INSTALLATION SERVICE POINT....2419
      INSPECTION....2420
        REFRIGERANT-TEMPERATURE SWITCH SIMPLE CHECK....2420
        COMPRESSOR A/C COMPRESSOR CLUTCH OPERATION INSPECTION....2420
        DISASSEMBLY SERVICE POINT....2421
        ASSEMBLY SERVICE POINTS....2422
    CONDENSER AND CONDENSER FAN MOTOR....2424
      REMOVAL SERVICE POINT....2425
      INSTALLATION SERVICE POINT....2425
      INSPECTION....2425
        CONDENSER FAN MOTOR CHECK....2425
    REFRIGERANT LINE....2426
      REMOVAL SERVICE POINT....2427
      INSTALLATION SERVICE POINT....2427
    AMBIENT AIR TEMPERATURE SENSOR....2428
      INSPECTION....2428
        AMBIENT AIR TEMPERATURE CHECK....2428
    AMBIENT TEMPERATURE SENSOR....2429
    VENTILATORS....2430
    SPECIFICATIONS....2431
GR00005400A-23A....2433
  AUTOMATIC TRANSMISSION....2433
    GENERAL DESCRIPTION....2435
      TRANSMISSION....2435
      ELECTRONICALLY-CONTROLLED SYSTEM....2440
      SHIFT PATTERN CONTROL....2443
    AUTOMATIC TRANSMISSION DIAGNOSIS....2444
      DIAGNOSTIC FUNCTION....2445
        CHECK "N" RANGE LIGHT....2445
        ON-BOARD DIAGNOSTICS....2446
        HOW TO CONNECT THE SCAN TOOL (MUT-III)....2446
        HOW TO READ AND ERASE DIAGNOSTIC TROUBLE CODES....2447
        HOW TO READ DATA LIST....2448
        HOW TO PERFORM ACTUATOR TEST....2449
      TORQUE CONVERTER STALL TEST....2457
        TORQUE CONVERTER STALL TEST JUDGMENT RESULTS....2458
      HYDRAULIC PRESSURE TESTS....2458
      LINE PRESSURE ADJUSTMENT....2471
      DIAGNOSTIC TROUBLE CODE PROCEDURES....2474
      DTC 15 (P0713): Transmission Fluid Temperature Sensor System (Open Circuit)....2474
        DIAGNOSIS....2477
          STEP 1. Using scan tool MB991958, check data list item 15: Transmission Fluid Temperature Sensor...2477
          STEP 2. Measure the sensor output voltage at the A/T control solenoid valve assembly connector B-...2478
          STEP 3. Measure the ground voltage at the A/T control solenoid valve assembly connector B-02 by b...2478
          STEP 4. Check the sensor output voltage at A/T control solenoid valve assembly connector B-02...2479
          STEP 5. Check the transmission fluid temperature sensor at A/T control solenoid valve assembly co...2480
          STEP 6. Using scan tool MB991958, check data list item 15: Transmission Fluid Temperature Sensor...2481
          STEP 7. Check A/T control solenoid valve assembly connector B-02 for loose, corroded or damaged t...2481
          STEP 8. Measure the resistance of the ground circuit at A/T control solenoid valve assembly conne...2482
          STEP 9. Measure the sensor output voltage at PCM connector C-92 by backprobing...2483
          STEP 10. Check the harness for open circuit or damage between A/T control solenoid valve connecto...2484
          STEP 11. Check PCM connector C-92 for loose, corroded or damaged terminals, or terminals pushed b...2485
          STEP 12. Check the harness for a short circuit to ground between A/T control solenoid valve conne...2486
          STEP 13. Measure the ground voltage at PCM connector C-90 by backprobing...2487
          STEP 14. Check A/T control solenoid valve assembly connector B-02, joint connector C-71, intermed...2488
          STEP 15. Check the harness for open circuit or damage between A/T control solenoid valve connecto...2490
          STEP 16. Check PCM connector C-90 for loose, corroded or damaged terminals, or terminals pushed b...2491
      DTC 16 (P0712): Transmission Fluid Temperature Sensor System (Short Circuit)....2491
        DIAGNOSIS....2493
          STEP 1. Using scan tool MB991958, check data list item 15: Transmission Fluid Temperature Sensor...2493
          STEP 2. Measure the sensor output voltage at the A/T control solenoid valve assembly connector B-...2494
          STEP 3. Check A/T control solenoid valve assembly connector B-02 for loose, corroded or damaged t...2494
          STEP 4. Check the sensor output voltage at A/T control solenoid valve assembly connector B-02...2495
          STEP 5. Check the transmission fluid temperature sensor at A/T control solenoid valve assembly co...2496
          STEP 6. Using scan tool MB991958, check data list item 15: Transmission Fluid Temperature Sensor...2497
          STEP 7. Measure the sensor output voltage at PCM connector C-92 by backprobing...2498
          STEP 8. Check PCM connector C-92 for loose, corroded or damaged terminals, or terminals pushed ba...2499
          STEP 9. Check the harness for a short circuit to ground between A/T control solenoid valve connec...2500
      DTC 22 (P0715): Input Shaft Speed Sensor System....2501
        DIAGNOSIS....2504
          STEP 1. Using scan tool MB991958, check data list item 22: Input Shaft Speed Sensor...2504
          STEP 2. Measure the power supply voltage at input shaft speed sensor connector B-16...2505
          STEP 3. Check intermediate connector C-30 and junction block connector D-13 for loose, corroded o...2505
          STEP 4. Check the harness for open circuit or short circuit to ground between input shaft speed s...2506
          STEP 5. Measure the PCM to speed sensor output voltage at the input shaft speed sensor connector ...2506
          STEP 6. Measure the PCM output voltage to the speed sensor at the PCM connector C-92 by backprobing...2507
          STEP 7. Check input shaft speed sensor connector B-16, PCM connector C-92 and intermediate connec...2508
          STEP 8. Check the harness for open circuit or damage between input shaft speed sensor connector B...2510
          STEP 9. Check input shaft speed sensor connector B-16, PCM connector C-92 and intermediate connec...2511
          STEP 10. Check the harness for short circuit to ground between input shaft speed sensor connector...2513
          STEP 11. Measure the ground circuit for resistance at the input shaft speed sensor connector B-16...2514
          STEP 12. Measure the resistance at PCM connector C-90 by backprobing...2515
          STEP 13. Check input shaft speed sensor connector B-16, joint connector C-71, intermediate connec...2516
          STEP 14. Check the harness for open circuit or damage between input shaft speed sensor harness si...2518
          STEP 15. Check PCM connector C-90 for loose, corroded or damaged terminals, or terminals pushed b...2519
          STEP 16. Using an oscilloscope, check the input shaft speed sensor waveform at PCM connectors C-9...2520
          STEP 17. Replace the input shaft speed sensor...2521
          STEP 18. Replace the reverse clutch retainer...2521
          STEP 19. Using scan tool MB991958, check data list item 22: Input Shaft Speed Sensor...2522
      DTC 23 (P0720): Output Shaft Speed Sensor System....2523
        DIAGNOSIS....2526
          STEP 1. Using scan tool MB991958, check data list item 23: Output Shaft Speed Sensor...2526
          STEP 2. Measure the power supply voltage at output shaft speed sensor connector B-15...2527
          STEP 3. Check intermediate connector C-30 and junction block connector D-13 for loose, corroded o...2527
          STEP 4. Check the harness for open circuit or short circuit to ground between output shaft speed ...2528
          STEP 5. Measure the PCM to speed sensor output voltage at output shaft speed sensor connector B-15...2528
          STEP 6. Measure the PCM output voltage to the speed sensor at PCM connector C-92 by backprobing...2529
          STEP 7. Check output shaft speed sensor connector B-15, PCM connector C-92 and intermediate conne...2530
          STEP 8. Check the harness for open circuit or damage between output shaft speed sensor connector ...2532
          STEP 9. Check output shaft speed sensor connector B-15, PCM connector C-92 and intermediate conne...2533
          STEP 10. Check the harness for short circuit to ground between output shaft speed sensor connecto...2535
          STEP 11. Measure the ground circuit for resistance at output shaft speed sensor connector B-15...2536
          STEP 12. Measure the resistance at PCM connector C-90 by backprobing...2537
          STEP 13. Check output shaft speed sensor connector B-15, joint connector C-71, intermediate conne...2538
          STEP 14. Check the harness for open circuit or damage between output shaft speed sensor harness s...2540
          STEP 15. Check PCM connector C-90 for loose, corroded or damaged terminals, or terminals pushed b...2541
          STEP 16. Using an oscilloscope, check the output shaft speed sensor waveform at PCM connectors C-...2542
          STEP 17. Replace the output shaft speed sensor...2543
          STEP 18. Replace the output shaft...2543
          STEP 19. Using scan tool MB991958, check data list item 23: Output Shaft Speed Sensor...2544
      DTC 26: Stoplight Switch System....2545
        DIAGNOSIS....2547
          STEP 1. Check the brake pedal height...2547
          STEP 2. Check the stoplight bulb...2547
          STEP 3. Using scan tool MB991958, check data list item 26: Stoplight Switch...2548
          STEP 4. Measure the stoplight switch power supply voltage at connectors C-66 by backprobing...2548
          STEP 5. Check stoplight switch connector C-66, junction block connector D-02 and D-09 for loose, ...2549
          STEP 6. Check the harness for damage between stoplight switch connector C-66 terminal 2 and the p...2549
          STEP 7. Measure the stoplight switch output voltage to the PCM at connector C-66 by backprobing...2550
          STEP 8. Check the stoplight switch...2550
          STEP 9. Measure the stoplight switch output voltage at PCM connector C-92 by backprobing...2551
          STEP 10. Check intermediate connector C-85 and PCM connector C-92 for loose, corroded or damaged ...2552
          STEP 11. Check the harness for damage between stoplight switch connector C-66 terminal 3 and PCM ...2553
          STEP 12. Using scan tool MB991958, check data list item 26: Stoplight Switch...2554
      DTC 27 (P0705): Transmission Range Switch System (Open Circuit)....2555
        DIAGNOSIS....2558
          STEP 1. Using scan tool MB991958, check data list item 61: Transmission Range Switch...2558
          STEP 2. Check the transmission range switch...2559
          STEP 3. Check transmission range switch connector B-01, intermediate connector C-30 and junction ...2560
          STEP 4. Check harness for open circuit or short circuit to ground between transmission range swit...2561
          STEP 5. Using scan tool MB991958, check data list item 61: Transmission Range Switch...2562
          STEP 6. Check the transmission range switch...2563
          STEP 7. Check transmission range switch connector B-01 for loose, corroded or damaged terminals, ...2564
          STEP 8. Measure the transmission range switch output voltage at PCM connector C-92 by backprobing...2565
          STEP 9. Check PCM connector C-92 and intermediate connector C-96 for loose, corroded or damaged t...2566
          STEP 10. Check harness for open circuit or short circuit to ground between transmission range swi...2567
          STEP 11. Check intermediate connector C-30 and combination meter connector C-03 for loose, corrod...2568
          STEP 12. Check harness for short circuit to ground between transmission range switch connector B-...2569
          STEP 13. Check PCM connector C-92 for loose, corroded or damaged terminals, or terminals pushed b...2570
          STEP 14. Check the transmission range switch...2571
          STEP 15. Check transmission range switch connector B-01 the for loose, corroded or damaged termin...2572
          STEP 16. Measure the transmission range switch output voltage at PCM connector C-92 by backprobing...2573
          STEP 17. Check PCM connector C-92 and intermediate connector C-96 for loose, corroded or damaged ...2574
          STEP 18. Check harness for open circuit or short circuit to ground between transmission range swi...2575
          STEP 19. Check intermediate connector C-30 and combination meter connector C-03 for loose, corrod...2576
          STEP 20. Check harness for short circuit to ground between transmission range switch connector B-...2577
          STEP 21. Check the transmission range switch...2578
          STEP 22. Check transmission range switch connector B-01 for loose, corroded or damaged terminals,...2579
          STEP 23. Measure the transmission range switch output voltage at PCM connector C-92 by backprobing...2580
          STEP 24. Check PCM connector C-92 and intermediate connector C-96 for loose, corroded or damaged ...2581
          STEP 25. Check harness for open circuit or short circuit to ground between transmission range swi...2582
          STEP 26. Check intermediate connector C-30 and combination meter connector C-03 for loose, corrod...2583
          STEP 27. Check harness for short circuit to ground between transmission range switch connector B-...2584
          STEP 28. Check the transmission range switch...2585
          STEP 29. Check transmission range switch connector B-01 for loose, corroded or damaged terminals,...2586
          STEP 30. Measure the transmission range switch output voltage at PCM connector C-92 by backprobing...2587
          STEP 31. Check PCM connector C-92 and intermediate connector C-96 for loose, corroded or damaged ...2588
          STEP 32. Check harness for open circuit or short circuit to ground between transmission range swi...2589
          STEP 33. Check intermediate connector C-30 and combination meter connector C-03 for loose, corrod...2590
          STEP 34. Check harness for short circuit to ground between transmission range switch connector B-...2591
          STEP 35. Check the transmission range switch...2592
          STEP 36. Check transmission range switch connector B-01 for loose, corroded or damaged terminals,...2593
          STEP 37. Measure the transmission range switch output voltage at PCM connector C-92 by backprobing...2594
          STEP 38. Check PCM connector C-92 and intermediate connector C-96 for loose, corroded or damaged ...2595
          STEP 39. Check harness for open circuit or short circuit to ground between transmission range swi...2596
          STEP 40. Check intermediate connector C-30 and combination meter connector C-03 for loose, corrod...2597
          STEP 41. Check harness for short circuit to ground between transmission range switch connector B-...2598
          STEP 42. Check the transmission range switch...2599
          STEP 43. Check transmission range switch connector B-01 for loose, corroded or damaged terminals,...2600
          STEP 44. Measure the transmission range switch output voltage at PCM connector C-92 by backprobing...2601
          STEP 45. Check PCM connector C-92 and intermediate connector C-96 for loose, corroded or damaged ...2602
          STEP 46. Check harness for open circuit or short circuit to ground between transmission range swi...2603
          STEP 47. Check intermediate connector C-30 and combination meter connector C-03 for loose, corrod...2604
          STEP 48. Check harness for short circuit to ground between transmission range switch connector B-...2605
          STEP 49. Check the transmission range switch...2606
          STEP 50. Check transmission range switch connector B-01 for loose, corroded or damaged terminals,...2607
          STEP 51. Measure the transmission range switch output voltage at PCM connector C-92 by backprobing...2608
          STEP 52. Check PCM connector C-92 and intermediate connector C-96 for loose, corroded or damaged ...2609
          STEP 53. Check harness for open circuit or short circuit to ground between transmission range swi...2610
          STEP 54. Check intermediate connector C-30 and combination meter connector C-03 for loose, corrod...2611
          STEP 55. Check harness for short circuit to ground between transmission range switch connector B-...2612
      DTC 28 (P0705): Transmission Range Switch System (Short Circuit)....2613
        DIAGNOSIS....2615
          STEP 1. Check the transmission range switch...2615
          STEP 2. Check transmission range switch connector B-01 for loose, corroded or damaged terminals, ...2616
          STEP 3. Check PCM connector C-92 for loose, corroded or damaged terminals, or terminals pushed ba...2616
          STEP 4. Measure the switch output voltage at PCM connector C-92 by backprobing. ("P" position)....2617
          STEP 5. Check intermediate connector C-96 for loose, corroded or damaged terminals, or terminals ...2618
          STEP 6. Check harness for open circuit or short circuit to ground between transmission range swit...2619
          STEP 7. Check intermediate connector C-30 and combination meter connector C-03 for loose, corrode...2620
          STEP 8. Check harness for damage or short circuit to ground between transmission range switch con...2621
          STEP 9. Measure the switch output voltage at PCM connector C-92 by backprobing. ("R" position)....2622
          STEP 10. Check intermediate connector C-96 for loose, corroded or damaged terminals, or terminals...2622
          STEP 11. Check harness for open circuit or short circuit to ground between transmission range swi...2623
          STEP 12. Check intermediate connector C-30 and combination meter connector C-03 for loose, corrod...2624
          STEP 13. Check harness for damage or short circuit to ground between transmission range switch co...2625
          STEP 14. Measure the switch output voltage at PCM connector C-92 by backprobing. ("N" position)....2626
          STEP 15. Check intermediate connector C-96 for loose, corroded or damaged terminals, or terminals...2626
          STEP 16. Check harness for open circuit or short circuit to ground between transmission range swi...2627
          STEP 17. Check intermediate connector C-30 and combination meter connector C-03 for loose, corrod...2628
          STEP 18. Check harness for damage or short circuit to ground between transmission range switch co...2629
          STEP 19. Measure the switch output voltage at PCM connector C-92 by backprobing. ("D" position)....2630
          STEP 20. Check intermediate connector C-96 for loose, corroded or damaged terminals, or terminals...2630
          STEP 21. Check harness for open circuit or short circuit to ground between transmission range swi...2631
          STEP 22. Check intermediate connector C-30 and combination meter connector C-03 for loose, corrod...2632
          STEP 23. Check harness for damage or short circuit to ground between transmission range switch co...2633
          STEP 24. Measure the switch output voltage at PCM connector C-92 by backprobing. ("3" position)....2634
          STEP 25. Check intermediate connector C-96 for loose, corroded or damaged terminals, or terminals...2634
          STEP 26. Check harness for open circuit or short circuit to ground between transmission range swi...2635
          STEP 27. Check intermediate connector C-30 and combination meter connector C-03 for loose, corrod...2636
          STEP 28. Check harness for damage or short circuit to ground between transmission range switch co...2637
          STEP 29. Measure the switch output voltage at PCM connector C-92 by backprobing. ("2" position)....2638
          STEP 30. Check intermediate connector C-96 for loose, corroded or damaged terminals, or terminals...2638
          STEP 31. Check harness for open circuit or short circuit to ground between transmission range swi...2639
          STEP 32. Check intermediate connector C-30 and combination meter connector C-03 for loose, corrod...2640
          STEP 33. Check harness for damage or short circuit to ground between transmission range switch co...2641
          STEP 34. Measure the switch output voltage at PCM connector C-92 by backprobing. ("L" position)....2642
          STEP 35. Check intermediate connector C-96 for loose, corroded or damaged terminals, or terminals...2642
          STEP 36. Check harness for open circuit or short circuit to ground between transmission range swi...2643
          STEP 37. Check intermediate connector C-30 and combination meter connector C-03 for loose, corrod...2644
          STEP 38. Check harness for damage or short circuit to ground between transmission range switch co...2645
          STEP 39. Using scan tool MB991958, check data list item 61: Transmission Range Switch...2646
      DTC 29 (P0500): Vehicle Speed Sensor System....2647
        DIAGNOSIS....2650
          STEP 1. Check the speedometer...2650
          STEP 2. Using scan tool MB991958, check data list item 29: Vehicle Speed Sensor...2650
          STEP 3. Using an oscilloscope, check the vehicle speed sensor waveform at PCM connector C-91 by b...2651
          STEP 4. Check PCM connector C-91 and intermediate connector C-16 for loose, corroded or damaged t...2652
          STEP 5. Check the harness for open circuit or short circuit to ground between combination meter c...2653
          STEP 6. Check PCM connector C-91 for loose, corroded or damaged terminals, or terminals pushed ba...2654
          STEP 7. Using scan tool MB991958, check data list item 29: Vehicle Speed Sensor...2655
      DTC 31 (P0753): Low-Reverse Solenoid Valve System....2656
        DIAGNOSIS....2660
          STEP 1. Using scan tool MB991958, check actuator test item 01: Low-Reverse Solenoid Valve...2660
          STEP 2. Using scan tool MB991958, read the A/T diagnostic trouble code...2661
          STEP 3. Using scan tool MB991958, read the A/T diagnostic trouble code...2661
          STEP 4. Measure the low-reverse solenoid valve resistance at A/T control solenoid valve assembly ...2662
          STEP 5. Measure the solenoid valve resistance at the low-reverse solenoid valve connector B-02-5 ...2662
          STEP 6. Check A/T control solenoid valve assembly connector B-02, PCM connector C-92 and intermed...2663
          STEP 7. Check the harness for an open or short circuit to ground between A/T control solenoid val...2665
          STEP 8. Measure the supply voltage at A/T control solenoid valve assembly connector B-02...2666
          STEP 9. Check A/T control solenoid valve assembly connector B-02, intermediate connector C-41 and...2667
          STEP 10. Check the harness for an open circuit or short circuit to ground between A/T control sol...2668
          STEP 11. Check A/T control solenoid valve assembly connector B-02, PCM connector C-92 and interme...2669
          STEP 12. Check the harness for an open or short circuit to ground between A/T control solenoid va...2671
          STEP 13. Check the harness for an open or short circuit to ground between A/T control solenoid va...2672
      DTC 32 (P0758): Underdrive Solenoid Valve System....2672
        DIAGNOSIS....2674
          STEP 1. Using scan tool MB991958, check actuator test item 02: Underdrive Solenoid Valve...2674
          STEP 2. Using scan tool MB991958, read the A/T diagnostic trouble code...2675
          STEP 3. Using scan tool MB991958, read the A/T diagnostic trouble code...2675
          STEP 4. Measure the underdrive solenoid valve resistance at A/T control solenoid valve assembly c...2676
          STEP 5. Measure the solenoid valve resistance at the underdrive solenoid valve connector B-02-1 i...2676
          STEP 6. Check A/T control solenoid valve assembly connector B-02, PCM connector C-92 and intermed...2677
          STEP 7. Check the harness for an open or short circuit to ground between A/T control solenoid val...2679
          STEP 8. Measure the supply voltage at A/T control solenoid valve assembly connector B-02...2680
          STEP 9. Check A/T control solenoid valve assembly connector B-02, intermediate connector C-41 and...2681
          STEP 10. Check the harness for an open circuit or short circuit to ground between A/T control sol...2682
          STEP 11. Check A/T control solenoid valve assembly connector B-02, PCM connector C-92 and interme...2683
          STEP 12. Check the harness for an open or short circuit to ground between A/T control solenoid va...2685
          STEP 13. Check the harness for an open or short circuit to ground between A/T control solenoid va...2686
      DTC 33 (P0763): Second Solenoid Valve System....2686
        DIAGNOSIS....2688
          STEP 1. Using scan tool MB991958, check actuator test item 03: Second Solenoid Valve...2688
          STEP 2. Using scan tool MB991958, read the A/T diagnostic trouble code...2689
          STEP 3. Using scan tool MB991958, read the A/T diagnostic trouble code...2689
          STEP 4. Measure the second solenoid valve resistance at A/T control solenoid valve assembly conne...2690
          STEP 5. Measure the solenoid valve resistance at the second solenoid valve connector B-02-2 insid...2690
          STEP 6. Check A/T control solenoid valve assembly connector B-02, PCM connector C-92 and intermed...2691
          STEP 7. Check the harness for an open or short circuit to ground between A/T control solenoid val...2693
          STEP 8. Measure the supply voltage at A/T control solenoid valve assembly connector B-02...2694
          STEP 9. Check A/T control solenoid valve assembly connector B-02, intermediate connector C-41 and...2695
          STEP 10. Check the harness for an open circuit or short circuit to ground between A/T control sol...2696
          STEP 11. Check A/T control solenoid valve assembly connector B-02, PCM connector C-92 and interme...2697
          STEP 12. Check the harness for an open or short circuit to ground between A/T control solenoid va...2699
          STEP 13. Check the harness for an open or short circuit to ground between A/T control solenoid va...2700
      DTC 34 (P0768): Overdrive Solenoid Valve System....2700
        DIAGNOSIS....2702
          STEP 1. Using scan tool MB991958, check actuator test item 04: Overdrive Solenoid Valve...2702
          STEP 2. Using scan tool MB991958, read the A/T diagnostic trouble code...2703
          STEP 3. Using scan tool MB991958, read the A/T diagnostic trouble code...2703
          STEP 4. Measure the overdrive solenoid valve resistance at A/T control solenoid valve assembly co...2704
          STEP 5. Measure the solenoid valve resistance at the overdrive solenoid valve connector B-02-3 in...2704
          STEP 6. Check A/T control solenoid valve assembly connector B-02, PCM connector C-92 and intermed...2705
          STEP 7. Check the harness for an open or short circuit to ground between A/T control solenoid val...2707
          STEP 8. Measure the supply voltage at A/T control solenoid valve assembly connector B-02...2708
          STEP 9. Check A/T control solenoid valve assembly connector B-02, intermediate connector C-41 and...2709
          STEP 10. Check the harness for an open circuit or short circuit to ground between A/T control sol...2710
          STEP 11. Check A/T control solenoid valve assembly connector B-02, PCM connector C-92 and interme...2711
          STEP 12. Check the harness for an open or short circuit to ground between A/T control solenoid va...2713
          STEP 13. Check the harness for an open or short circuit to ground between A/T control solenoid va...2714
      DTC 36 (P0743): Torque Converter Clutch Solenoid Valve System....2714
        DIAGNOSIS....2716
          STEP 1. Using scan tool MB991958, check actuator test item 06: Torque Converter Clutch Solenoid V...2716
          STEP 2. Using scan tool MB991958, read the A/T diagnostic trouble code...2717
          STEP 3. Using scan tool MB991958, read the A/T diagnostic trouble code...2717
          STEP 4. Measure the torque converter clutch solenoid valve resistance at A/T control solenoid val...2718
          STEP 5. Measure the solenoid valve resistance at the torque converter clutch solenoid valve conne...2718
          STEP 6. Check A/T control solenoid valve assembly connector B-02, PCM connector C-92 and intermed...2719
          STEP 7. Check the harness for an open or short circuit to ground between A/T control solenoid val...2721
          STEP 8. Measure the supply voltage at A/T control solenoid valve assembly connector B-02...2722
          STEP 9. Check A/T control solenoid valve assembly connector B-02, intermediate connector C-41 and...2723
          STEP 10. Check the harness for an open circuit or short circuit to ground between A/T control sol...2724
          STEP 11. Check A/T control solenoid valve assembly connector B-02, PCM connector C-92 and interme...2725
          STEP 12. Check the harness for an open or short circuit to ground between A/T control solenoid va...2727
          STEP 13. Check the harness for an open or short circuit to ground between A/T control solenoid va...2728
      DTC 41 (P0731): 1st Gear Incorrect Ratio DTC 42 (P0732): 2nd Gear Incorrect Ratio DTC 43 (P0733):...2729
        DIAGNOSIS....2739
          STEP 1. Using scan tool MB991958, read the A/T diagnostic trouble code...2740
          STEP 2. Check the hydraulic pressure...2740
          STEP 3. Adjust the line pressure...2740
          STEP 4. Disassemble and clean the valve body...2741
          STEP 5. Replace the PCM...2741
          STEP 6. Overhaul the A/T...2741
      DTC 52 (P0741): Torque Converter Clutch System....2742
        DIAGNOSIS....2744
          STEP 1. Using scan tool MB991958, read the A/T diagnostic trouble code...2744
          STEP 2. Using scan tool MB991958, check data list item 36: Torque Converter Clutch Solenoid Valve...2745
          STEP 3. Using scan tool MB991958, check data list item 52: Torque Converter Clutch Amount of Slip...2745
          STEP 4. Using scan tool MB991958, read the A/T diagnostic trouble code...2746
          STEP 5. Check the hydraulic pressure (for torque converter)...2746
          STEP 6. Adjust line pressure...2746
          STEP 7. Replace the PCM...2747
          STEP 8. Replace the valve body...2747
      DTC 53 (P0742): Torque Converter Clutch is Stuck On....2747
        DIAGNOSIS....2749
          STEP 1. Using scan tool MB991958, read the A/T diagnostic trouble code...2749
          STEP 2. Using scan tool MB991958, check data list item 52: Amount of Torque Converter Clutch Slip...2750
          STEP 3. Replace the PCM...2750
          STEP 4. Replace the valve body...2750
      DTC 54 (P1751): A/T Control Relay System....2751
        DIAGNOSIS....2755
          STEP 1. Using scan tool MB991958, check data list item 54: A/T Control Relay Output Voltage...2755
          STEP 2. Check the A/T control relay...2756
          STEP 3. Check A/T control relay connector C-97 for loose, corroded or damaged terminals, or termi...2756
          STEP 4. Measure the supply voltage at A/T control relay connector C-97...2757
          STEP 5. Check junction block connectors D-09 and D-02 for loose, corroded or damaged terminals, o...2757
          STEP 6. Check the harness for open circuit or short circuit to ground between A/T control relay c...2758
          STEP 7. Measure the resistance at A/T control relay connector C-97...2758
          STEP 8. Check the harness for open circuit or damage between A/T control relay connector C-97 ter...2758
          STEP 9. Measure the control voltage to A/T control relay connector C-97...2759
          STEP 10. Measure the supply voltage at PCM connector C-90 by backprobing...2760
          STEP 11. Check intermediate connector C-85 and PCM connector C-90 for loose, corroded or damaged ...2761
          STEP 12. Check the harness for open circuit or damage between PCM connector C-90 terminal 50 and ...2762
          STEP 13. Check for a short circuit to ground between PCM connector C-90 terminal 50 and A/T contr...2763
          STEP 14. Measure the A/T control relay output voltage at PCM connector C-91 by backprobing...2764
          STEP 15. Check intermediate connector C-41 and PCM connector C-91 for loose, corroded or damaged ...2765
          STEP 16. Check harness for open circuit or short circuit to ground between PCM connector C-91 ter...2766
          STEP 17. Using scan tool MB991958, check data list item 54: A/T control relay output Voltage...2767
      DTC 56: "N" Range Light System....2768
        DIAGNOSIS....2770
          STEP 1. Check the "N" range light bulb...2770
          STEP 2. Check the "N" range light bulb...2770
          STEP 3. Check combination meter connectors C-03 and C-04 for loose, corroded or damaged terminals...2770
          STEP 4. Measure the resistance at combination meter connector C-04...2771
          STEP 5. Check the harness for open circuit or damage between combination meter connector C-04 ter...2771
          STEP 6. Check combination meter connector C-03, intermediate connectors C-30, C-96 and PCM connec...2772
          STEP 7. Check the harness for open circuit, short circuit to ground and damage between combinatio...2773
          STEP 8. Using scan tool MB991958, read the A/T diagnostic trouble code...2774
GR00005400B-23A....2775
  AUTOMATIC TRANSMISSION....0
    AUTOMATIC TRANSMISSION DIAGNOSIS....0
      SYMPTOM PROCEDURES <AUTOMATIC TRANSMISSION>....2775
      INSPECTION PROCEDURE 1: Engine does not Crank...2775
        DIAGNOSIS....2775
          STEP 1. Using scan tool MB991958, read the A/T diagnostic trouble code...2775
          STEP 2. Check the transmission control cable assembly...2776
          STEP 3. Check the engine...2776
          STEP 4. Check the torque converter...2776
          STEP 5. Repair or replace the starter...2776
          STEP 6. Replace the transmission oil pump...2777
          STEP 7. Replace the PCM...2777
      INSPECTION PROCEDURE 2: Does not Move Forward....2777
        DIAGNOSIS....2778
          STEP 1. Using scan tool MB991958, check actuator test item 02: Underdrive Solenoid Valve...2778
          STEP 2. Check the hydraulic pressure...2778
          STEP 3. Check the underdrive clutch system...2779
          STEP 4. Disassemble and clean the valve body...2779
          STEP 5. Check the underdrive clutch...2779
          STEP 6. Replace the PCM...2779
      INSPECTION PROCEDURE 3: Does not Move Backward....2780
        DIAGNOSIS....2780
          STEP 1. Using scan tool MB991958, check actuator test item 01: Low-Reverse Solenoid Valve...2780
          STEP 2. Check the hydraulic pressure (for reverse clutch)...2781
          STEP 3. Check the hydraulic pressure (for low-reverse brake)...2781
          STEP 4. Check the reverse clutch system and low-reverse brake system...2781
          STEP 5. Disassemble and clean the valve body...2781
          STEP 6. Check the reverse clutch, low-reverse brake or both. Remove the transmission...2782
          STEP 7. Replace the PCM...2782
      INSPECTION PROCEDURE 4: Does not Move (Forward or Backward)....2782
        DIAGNOSIS....2782
          STEP 1. Check the hydraulic pressure...2782
          STEP 2. Disassemble and clean the valve body...2783
          STEP 3. Check the transmission power train components...2783
          STEP 4. Replace the transmission oil pump...2783
          STEP 5. Replace the PCM...2783
      INSPECTION PROCEDURE 5: Engine Stalls when Moving Selector Lever from "N" to "D" or "N" to "R"...2784
        DIAGNOSIS....2784
          STEP 1. Check the engine system...2784
          STEP 2. Replace the torque converter clutch solenoid valve...2784
          STEP 3. Disassemble and clean the valve body...2784
          STEP 4. Replace the torque converter assembly...2785
          STEP 5. Replace the PCM...2785
      INSPECTION PROCEDURE 6: Shift Shock when Shifting from "N" to "D" and Long Delay....2785
        DIAGNOSIS....2785
          STEP 1. Using scan tool MB991958, check actuator test item 02: Underdrive Solenoid Valve...2786
          STEP 2. Check when shift shock occurs...2786
          STEP 3. Check the hydraulic pressure (for underdrive clutch)...2786
          STEP 4. Check the underdrive clutch system...2787
          STEP 5. Check the underdrive clutch...2787
          STEP 6. Check shift shock...2787
          STEP 7. Using scan tool MB991958, check data list item 11: TP Sensor...2788
          STEP 8. Disassemble and clean the valve body...2788
          STEP 9. Replace the PCM...2788
      INSPECTION PROCEDURE 7: Shift Shock when Shifting from "N" to "R" and Long Delay....2789
        DIAGNOSIS....2789
          STEP 1. Using scan tool MB991958, check actuator test item 01: Low-Reverse Solenoid Valve...2789
          STEP 2. Check when shift shock occurs...2790
          STEP 3. Check the hydraulic pressure (for reverse clutch)...2790
          STEP 4. Check the hydraulic pressure (for low-reverse brake)...2790
          STEP 5. Check the reverse clutch system and low-reverse brake system...2790
          STEP 6. Check the reverse clutch and low-reverse brake...2791
          STEP 7. Check shift shock...2791
          STEP 8. Using scan tool MB991958, check data list item 11: TP Sensor...2791
          STEP 9. Disassemble and clean the valve body...2792
          STEP 10. Replace the PCM...2792
      INSPECTION PROCEDURE 8: Shift Shock when Shifting from "N" to "D," "N" to "R" and Long Delay....2792
        DIAGNOSIS....2792
          STEP 1. Check the hydraulic pressure...2792
          STEP 2. Adjust line pressure...2792
          STEP 3. Check when shift shock occurs...2793
          STEP 4. Replace the transmission oil pump...2793
          STEP 5. Disassemble and clean the valve body...2793
          STEP 6. Replace the PCM...2793
      INSPECTION PROCEDURE 9: Shift Shock and Slipping....2794
        DIAGNOSIS....2794
          STEP 1. Using scan tool MB991958, check actuator test...2794
          STEP 2. Check the hydraulic pressure...2795
          STEP 3. Adjust the line pressure...2795
          STEP 4. Replace the transmission oil pump...2795
          STEP 5. Disassemble and clean the valve body...2795
          STEP 6. Check each brake and clutch...2796
          STEP 7. Replace the PCM...2796
      INSPECTION PROCEDURE 10: Early or Late Shifting All Gears....2796
        DIAGNOSIS....2796
          STEP 1. Using scan tool MB991958, check data list item 23: Output Shaft Speed Sensor...2797
          STEP 2. Using scan tool MB991958, check data list item 11: TP Sensor...2797
          STEP 3. Using scan tool MB991958, check data list...2798
          STEP 4. Adjust the line pressure...2798
          STEP 5. Disassemble and clean the valve body...2799
          STEP 6. Replace each solenoid valve...2799
          STEP 7. Replace the PCM...2799
      INSPECTION PROCEDURE 11: Early or Late Shifting in Some Gears....2799
        DIAGNOSIS....2799
          STEP 1. Using scan tool MB991958, check actuator test item 14: INVECS-II Cancel Command...2800
          STEP 2. Check the shift points...2800
          STEP 3. Disassemble and clean the valve body...2800
          STEP 4. Replace the PCM...2801
      INSPECTION PROCEDURE 12: No Diagnostic Trouble Codes (Does not Shift)....2801
        DIAGNOSIS....2802
          STEP 1. Check the vehicle acceleration...2802
          STEP 2. Measure the backup power supply voltage at PCM connector C-90 by backprobing...2802
          STEP 3. Check PCM connector C-90 for loose, corroded or damaged terminals, or terminals pushed ba...2803
          STEP 4. Check the harness for open circuit between PCM connector C-90 terminal 66 and fusible link...2803
          STEP 5. Using scan tool MB991958, check data list item 61: Transmission Range Switch...2804
      INSPECTION PROCEDURE 13: Poor Acceleration....2804
        DIAGNOSIS....2804
          STEP 1. Check the engine system...2804
          STEP 2. Check each brake and clutch...2805
          STEP 3. Perform the hydraulic pressure test...2805
          STEP 4. Check each brake system and clutch system...2805
          STEP 5. Check each brake system and clutch system...2805
          STEP 6. Replace the PCM...2805
      INSPECTION PROCEDURE 14: Vibration....2806
        DIAGNOSIS....2806
          STEP 1. Using scan tool MB991958, check actuator test item 06: Torque Converter Clutch Solenoid V...2806
          STEP 2. Check the vibration...2807
          STEP 3. Check the torque converter hydraulic pressure...2807
          STEP 4. Replace the torque converter assembly...2807
          STEP 5. Disassemble and clean the valve body...2807
          STEP 6. Replace the PCM...2807
      INSPECTION PROCEDURE 15: Vehicle Shifts Differently with A/C Engaged...2808
        DIAGNOSIS....2810
          STEP 1. Using scan tool MB991958, check data list item 65: Dual Pressure Switch...2810
          STEP 2. Check dual pressure switch connector A-23 for loose, corroded or damaged terminals, or te...2810
          STEP 3. Measure the power supply voltage at dual pressure switch connector A-23...2811
          STEP 4. Measure the power supply voltage at automatic compressor controller connector C-09 by bac...2811
          STEP 5. Check automatic compressor controller connector C-09 and intermediate connector C-41 for ...2812
          STEP 6. Check harness for short circuit to ground between dual pressure switch connector A-23 ter...2812
          STEP 7. Using scan tool MB991958, check data list item 65: Dual Pressure Switch...2813
          STEP 8. Check automatic compressor controller connector C-09 and intermediate connector C-41 for ...2814
          STEP 9. Check the harness for open circuit between dual pressure switch connector A-23 terminal 1...2814
          STEP 10. Measure the switch output voltage at PCM connector C-91 by backprobing...2815
          STEP 11. Check A/C refrigerant temperature switch connector A-25, intermediate connector A-89 and...2816
          STEP 12. Check harness for open circuit or short circuit to ground between dual pressure switch c...2817
          STEP 13. Check the dual pressure switch...2817
          STEP 14. Measure the A/C refrigerant temperature switch terminal...2818
          STEP 15. Using scan tool MB991958, check data list item 65: Dual Pressure Switch...2818
          STEP 16. Check connector C-91 at PCM for loose, corroded or damaged terminals, or terminals pushe...2819
      INSPECTION PROCEDURE 16: Transmission won’t Downs....2820
        DIAGNOSIS....2822
          STEP 1. Using scan tool MB991958, check data list item 66: Overdrive Off Signal (Auto-cruise cont...2822
          STEP 2. Check the auto-cruise system...2822
          STEP 3. Measure the signal voltage at PCM connector C-91 by backprobing...2823
          STEP 4. Check intermediate connector C-41 and PCM connector C-91 for looser, corroded or damaged ...2824
          STEP 5. Check the harness for open circuit, short circuit to ground or damage between auto-cruise...2825
          STEP 6. Measure the signal voltage at auto-cruise control-ECU connector C-35 by backprobing...2826
          STEP 7. Check auto-cruise control-ECU connector C-35 for looser, corroded or damaged terminals, o...2826
          STEP 8. Check auto-cruise control-ECU connector C-35 and intermediate connector C-41 for looser, ...2827
          STEP 9. Check harness for short circuit to ground between auto-cruise control-ECU connector C-35 ...2828
          STEP 10. Using scan tool MB991958, check data list item 66: Overdrive Off Signal (Auto-cruise con...2829
      INSPECTION PROCEDURE 17: Transfer Low Detection Switch System....2830
        DIAGNOSIS....2832
          STEP 1. Using scan tool MB991958, check data list item 75: Transfer Low Detection Switch...2832
          STEP 2. Check transfer low detection switch connector B-17 for loose, corroded or damaged termina...2832
          STEP 3. Measure the switch output voltage at transfer low detection switch connector B-17...2833
          STEP 4. Measure the switch output voltage at PCM connector C-92 by backprobing...2834
          STEP 5. Check PCM connector C-92 and intermediate connector C-96 for loose, corroded or damaged t...2835
          STEP 6. Check harness for open circuit between transfer low detection switch connector B-17 termi...2836
          STEP 7. Check PCM connector C-92 and intermediate connector C-96 for loose, corroded or damaged t...2837
          STEP 8. Check harness for short circuit to ground between transfer low detection switch connector...2838
          STEP 9. Using scan tool MB991958, check data list item 75: Transfer Low Detection Switch...2839
          STEP 10. Measure the resistance at transfer low detection switch connector B-17...2839
          STEP 11. Check PCM connector C-92 for loose, corroded or damaged terminals, or terminals pushed b...2840
    A/T FAULTY OPERATION PREVENTION MECHANISM DIAGNOSIS....2850
      SYMPTOM PROCEDURES <KEY INTERLOCK AND SHIFT LOCK MECHANISMS>....2851
      INSPECTION PROCEDURE 1: Selector Lever can be Moved from "P" to "R" Position without Depressing B...2851
        DIAGNOSIS....2851
          STEP 1. Check the fit of the lock cam...2851
          STEP 2. Check the lock cam...2851
          STEP 3. Check the fit of the shift lock cable...2851
          STEP 4. Check the shift lock cable...2851
      INSPECTION PROCEDURE 2: Selector Lever cannot be Moved from "P" to "R" Position with Brake Pedal ...2851
        DIAGNOSIS....2852
          STEP 1. Check the connection of lock cam and key interlock cable...2852
          STEP 2. Check the connection of selector lever assembly and shift transmission control cable...2852
          STEP 3. Check the fit of the shift lock cable...2852
          STEP 4. Check the shift lock cable...2852
          STEP 5. Check the fit of the key interlock cable...2852
          STEP 6. Check the key interlock cable...2852
          STEP 7. Check the fit of the transmission control cable...2852
          STEP 8. Check the transmission control cable...2852
      INSPECTION PROCEDURE 3: Selector Lever can be Moved from "P" to "R" Position with Brake Padal Dep...2853
        DIAGNOSIS....2853
          STEP 1. Check the connection of lock cam and key interlock cable...2853
          STEP 2. Check the fit of the lock cam...2853
          STEP 3. Check the lock cam...2853
          STEP 4. Check the fit of the key interlock cable...2853
          STEP 5. Check the key interlock cable...2853
      INSPECTION PROCEDURE 4: Selector Lever cannot be Moved from "P" to "R" Position Smoothly...2853
        DIAGNOSIS....2853
          STEP 1. Check the connection of lock cam and key interlock cable...2853
          STEP 2. Check the connection of selector lever assembly and transmission control cable...2854
          STEP 3. Check the fit of the lock cam...2854
          STEP 4. Check the lock cam...2854
          STEP 5. Check the fit of the shift lock cable...2854
          STEP 6. Check the shift lock cable...2854
          STEP 7. Check the fit of the key interlock cable...2854
          STEP 8. Check the key interlock cable...2854
          STEP 9. Check the fit of the transmission control cable...2854
          STEP 10. Check the transmission control cable...2854
      INSPECTION PROCEDURE 5: Selector Lever cannot be Moved from "R" Position to "P" Position...2855
        DIAGNOSIS....2855
          STEP 1. Check the connection of selector lever assembly and transmission control cable...2855
          STEP 2. Check the fit of the lock cam...2855
          STEP 3. Check the lock cam...2855
          STEP 4. Check the fit of the transmission control cable...2855
          STEP 5. Check the transmission control cable...2855
      INSPECTION PROCEDURE 6: Ignition Key cannot be Turned to "LOCK" (OFF) Position when Selector Leve...2855
        DIAGNOSIS....2855
          STEP 1. Check the connection of lock cam and key interlock cable...2855
          STEP 2. Check the fit of the lock cam...2856
          STEP 3. Check the lock cam...2856
          STEP 4. Check the fit of the key interlock cable...2856
          STEP 5. Check the key interlock cable...2856
          STEP 6. Check the fit of the transmission control cable...2856
      INSPECTION PROCEDURE 7: Ignition Key can be Turned to "LOCK" (OFF) Position when Selector Lever i...2856
        DIAGNOSIS....2856
          STEP 1. Check the connection of lock cam and key interlock cable...2856
          STEP 2. Check the fit of the lock cam...2856
          STEP 3. Check the lock cam...2857
          STEP 4. Check the fit of the key interlock cable...2857
          STEP 5. Check the key interlock cable...2857
          STEP 6. Check the fit of the transmission control cable...2857
    SPECIAL TOOLS....2858
    ON-VEHICLE SERVICE....2859
      ESSENTIAL SERVICE....2862
      TRANSMISSION FLUID CHECK....2862
      TRANSMISSION FLUID CHANGE....2863
      FLUSHING COOLERS AND TUBES....2865
      OIL COOLER FLOW CHECK....2866
      TP SENSOR ADJUSTMENT....2867
      TRANSMISSION RANGE SWITCH CONTINUITY CHECK....2867
      TRANSMISSION RANGE SWITCH AND CONTROL CABLE ADJUSTMENT....2868
      HIGH RANGE/LOW RANGE DETECTION SWITCH CHECK <V4A51>....2869
      TRANSFER LOW DETECTION SWITCH CHECK <V4A51>....2869
      CENTER DIFFERENTIAL LOCK DETECTION SWITCH CHECK <V4A51>....2870
      CENTER DIFFERENTIAL LOCK OPERATION DETECTION SWITCH CHECK <V4A51>....2870
      TRANSFER OIL CHECK <V4A51>....2871
      TRANSFER OIL REPLACEMENT <V4A51>....2871
      SELECTOR LEVER OPERATION CHECK....2871
      KEY INTERLOCK MECHANISM CHECK....2872
      SHIFT LOCK MECHANISM CHECK....2873
      AUTOMATIC TRANSMISSION CONTROL COMPONENT CHECK....2873
      CRANKSHAFT POSITION SENSOR CHECK....2873
      TP SENSOR CHECK....2873
      TRANSMISSION FLUID TEMPERATURE SENSOR CHECK....2874
      TRANSMISSION RANGE SWITCH CHECK....2874
      STOPLIGHT SWITCH CHECK....2874
      VEHICLE SPEED SENSOR CHECK....2874
      DUAL PRESSURE SWITCH CHECK....2874
      A/T CONTROL RELAY CHECK....2875
      SOLENOID VALVE CHECK....2875
    TRANSMISSION CONTROL....2877
      INSTALLATION SERVICE POINTS....2878
      INSPECTION....2880
        ASSEMBLY SERVICE POINT....2882
    A/T KEY INTERLOCK AND SHIFT LOCK MECHANISMS....2883
      INSTALLATION SERVICE POINTS....2884
    TRANSMISSION AND TRANSFER ASSEMBLY....2885
      REMOVAL SERVICE POINTS....2888
      INSTALLATION SERVICE POINTS....2888
    OIL PAN....2890
      REMOVAL SERVICE POINT....2891
      INSTALLATION SERVICE POINT....2891
    TRANSMISSION FLUID COOLER, HOSE AND PIPE....2892
      INSTALLATION SERVICE POINTS....2893
    POWERTRAIN CONTROL MODULE (PCM)....2894
    4WD INDICATOR ECU....2895
      INSPECTION....2895
        4WD INDICATOR-ECU....2895
    SPECIFICATIONS....2896
GR00005500-51....2899
  EXTERIOR....2899
    FRONT BUMPER ASSEMBLY....2900
    REAR BUMPER ASSEMBLY....2902
    UNDER FLOOR SPARE TIRE CARRIER....2903
    GRILL, MOLDING AND GARNISH....2903
      GRILL, MOLDING AND GARNISH....2904
        REMOVAL SERVICE POINT....2906
        INSTALLATION SERVICE POINTS....2907
    WIDE FENDER....2908
      REMOVAL SERVICE POINT....2909
      INSTALLATION SERVICE POINT....2909
    SIDE STEP....2910
      REMOVAL SERVICE POINT....2911
      INSTALLATION SERVICE POINT....2912
    ROOF RAIL....2913
    WINDSHIELD WIPER AND WASHER....2913
      WINDSHIELD WIPER AND WASHER....2914
        REMOVAL SERVICE POINT....2915
        INSTALLATION SERVICE POINT....2915
      INSPECTION....2915
        WINDSHIELD WIPER AND WINDSHIELD WASHER SWITCH CHECK....2915
        INTERMITTENT WIPER RELAY (INTERMITTENT OPERATION INSPECTION)....2916
        FRONT WIPER MOTOR CHECK....2916
        FRONT WASHER MOTOR CHECK....2916
        WINDSHIELD WASHER FLUID EJECTION CHECK....2917
    REAR WIPER AND WASHER....2917
      REAR WIPER AND WASHER....2918
        INSTALLATION SERVICE POINTS....2919
      INSPECTION....2919
        REAR WIPER AND WASHER SWITCH CHECK....2919
        REAR WIPER MOTOR CHECK....2920
        REAR INTERMITTENT WIPER RELAY CHECK....2920
        REAR WASHER MOTOR CHECK....2920
        REAR WASHER FLUID EJECTION CHECK....2921
    MARK....2921
      INSTALLATION SERVICE POINT....2922
    DOOR MIRROR....2923
      DOOR MIRROR....2924
        REMOVAL SERVICE POINT....2924
      INSPECTION....2925
        ELECTRIC REMOTE CONTROL MIRROR OPERATION CHECK....2925
        HEATED MIRROR OPERATION CHECK....2926
        DOOR MIRROR CONTROL SWITCH CONTINUITY CHECK....2926
    SPECIFICATIONS....2927
GR00005600-52B....2929
  SUPPLEMENTAL RESTRAINT SYSTEM (SRS)....2929
    GENERAL DESCRIPTION....2931
      WARNING/CAUTION LABELS....2933
      SRS air bag special connector....2937
    SRS SERVICE PRECAUTIONS....2945
    SRS AIR BAG DIAGNOSIS....2949
      DIAGNOSTIC FUNCTION....2949
        HOW TO CONNECT THE SCAN TOOL (MUT-III)....2949
        HOW TO READ AND ERASE DIAGNOSTIC TROUBLE CODES....2950
      DIAGNOSTIC TROUBLE CODE PROCEDURES....2953
      DTC 1A Front impact sensor (LH) circuit short DTC 1B Front impact sensor (LH) circuit open DTC 1C...2953
        DIAGNOSIS....2955
          Step 1. Check the front impact sensor...2955
          Step 2. Measure the resistance and voltage at SRS-ECU connector C-24...2955
          Step 3. Check the wiring harness between the right front impact sensor connector A-32 (terminals ...2957
          Step 4. Recheck for diagnostic trouble code...2958
      DTC 14: Analog G-sensor System in the SRS-ECU DTC 15: Safing G-Sensor Short Circuit DTC 16: Safin...2959
        DIAGNOSIS....2959
      DTC 21 : Driver's Side Air Bag Module (Squib) System Fault 1DTC 22: Driver's Side Air Bag Module ...2960
        DIAGNOSIS....2961
          STEP 1. Check the clock spring connector D-20...2962
          STEP 2. Check the clock spring line. (Using scan tool MB991958, read the diagnostic trouble code.)....2962
          STEP 3. Check the clock spring...2962
          STEP 4. Check the harness wires between SRS-ECU connector C-24 (terminal No.11, 12) and clock spr...2963
          STEP 5. Recheck for diagnostic trouble code...2963
      DTC 24: Passenger (Front) Side Air Bag Module (Squib) System Fault 1 DTC 25: Passenger (Front) Si...2964
        STEP 1. Check the passenger’s side air bag module....2966
        STEP 2. Check harness wires between SRS-ECU connector C-24 (terminal No.9 and 10) and front passe...2967
        STEP 3. Recheck for diagnostic trouble code...2967
      DTC 26: Driver's Side Seat Belt Pre-Tensioner (Squib) System Fault 1 DTC 27: Driver's Side Seat B...2968
        STEP 1. Check the driver’s side seat belt pre-ten....2970
        STEP 2. Check harness wires between SRS-ECU connector C-110 (terminal No.29 and 30) and driver's ...2971
        STEP 3. Recheck for diagnostic trouble code...2972
      DTC 34: Connector Lock System Detects Connector Unlocked....2972
        DIAGNOSIS....2972
          STEP 1. Check SRS-ECU connector C-24 and C-110 for damage. If SRS-ECU connector C-24 and C-110 fo...2973
          STEP 2. Recheck for diagnostic trouble code...2974
      DTC 35: SRS-ECU Air Bag Condition Monitor Detects Deployed Air Bag....2974
        DIAGNOSIS....2974
      DTC 39 AIR BAGS DEPLOYED SIMULTANEOUSLY....2974
        DIAGNOSIS....2974
      DTC 41: IG1 Power Circuit System (Fuse No. 7 Circuit)DTC 42: IG1 Power Circuit System (Fuse No. 8...2975
        DIAGNOSIS....2976
          STEP 1. Check the ground line at SRS-ECU connector C-24...2977
          STEP 2. Check the harness wires between SRS-ECU connector C-24 (terminal No.7) and ground...2978
          STEP 3. Measure the ignition switch (IG1) line voltage at SRS-ECU connector C-24...2979
          STEP 4. Check the harness wires between the ignition switch (IG1) and SRS-ECU connector C-24 (ter...2980
          STEP 5. Recheck for diagnostic trouble code...2981
      DTC 43: SRS Warning Light Drive Circuit System Fault 1 (Light does not Illuminate.)/SRS Warning L...2982
        DIAGNOSIS....2983
          STEP 1. Check the SRS warning light line at SRS-ECU connector C-24...2984
          STEP 2. Check the SRS warning light bulb...2984
          STEP 3. Check the harness wires between ignition switch (IG1) and SRS-ECU connector C-24 (termina...2985
          STEP 4. Check the ground line at SRS-ECU connector C-24...2987
          STEP 5. Check the harness wires between SRS-ECU connector C-24 (terminal No.7) and ground...2988
          STEP 6.Recheck for diagnostic trouble code...2988
      DTC 46 Improper installation of SRS-ECU....2989
      SRS WARNING LIGHT CHECK....2989
      SYMPTOM PROCEDURES....2990
      INSPECTION PROCEDURE 1: Communication with Scan Tool MB991502 is not Possible with all System...2990
        DIAGNOSIS....2990
      INSPECTION PROCEDURE 2: Communication with Scan Tool MB991958 is not Possible with the SRS System...2991
        DIAGNOSIS....2992
          STEP 1. Check the ground line at the SRS-ECU connector C-24...2993
          STEP 2. Check the harness wires between SRS-ECU connector C-24 (terminal No.7) and ground...2994
          STEP 3. Measure the ignition switch (IG1) line voltage at the SRS-ECU connector C-24...2995
          STEP 4. Check the harness wires between ignition switch (IG1) and SRS-ECU connector C-24 (termina...2996
          STEP 5. Check the harness wires between SRS-ECU connector C-24 (terminal No.20) and data link con...2997
          STEP 6. Retest the system...2998
    SPECIAL TOOLS....2999
    TEST EQUIPMENT....3001
    SRS MAINTENANCE....3001
    POST-COLLISION DIAGNOSIS....3002
      SRS-ECU MEMORY CHECK....3002
      REPAIR PROCEDUR....3003
    INDIVIDUAL COMPONENT SERVICE....3006
    FRONT IMPACT SENSORS....3007
      REMOVAL SERVICE POINT....3008
      INSTALLATION SERVICE POINTS....3008
      INSPECTION....3009
        FRONT IMPACT SENSOR CHECK....3009
    SRS CONTROL UNIT (SRS-ECU)....3010
      REMOVAL SERVICE POINT....3011
      INSTALLATION SERVICE POINTS....3011
      INSPECTION....3012
    AIR BAG MODULES AND CLOCK SPRING....3012
      REMOVAL SERVICE POINTS....3015
      INSTALLATION SERVICE POINTS....3016
      INSPECTION....3018
    SEAT BELTS WITH PRE-TENSIONER....3021
      REMOVAL SERVICE POINTS....3022
      INSTALLATION SERVICE POINTS....3022
      INSPECTION....3023
    AIR BAG MODULE AND SEAT BELT PRE-TENSIONER DISPOSAL PROCEDURES....3024
      UNDEPLOYED AIR BAG MODULE AND SEAT BELT PRE-TENSIONER DISPOSAL....3024
      DEPLOYED AIR BAG MODULE DISPOSAL....3031
    SENSOR CABLE INSTALLATION PROCEDURE....3032
    SPECIFICATIONS....3034
GR00005700-31....3035
  WHEEL AND TIRE....3035
    WHEEL AND TIRE DIAGNOSIS....3036
      WHEEL BALANCE ACCURACY....3037
      TIRE RADIAL-FORCE VARIATION CHECK....3039
    ON-VEHICLE SERVICE....3041
      TIRE INFLATION PRESSURE CHECK....3041
      TIRE WEAR CHECK....3041
      WHEEL RUNOUT CHECK....3041
    SPECIFICATIONS....3042
GR00005800-33A....3043
  FRONT SUSPENSION....3043
    GENERAL DESCRIPTION....3044
    SPECIAL TOOLS....3044
    ON-VEHICLE SERVICE....3045
      FRONT WHEEL ALIGNMENT CHECK AND ADJUSTMENT....3045
        Charts for Shim Increase or Decrease....3047
      BALL JOINT DUST COVER CHECK....3047
    SHOCK ABSORBER ASSEMBLY AND UPPER ARM....3048
      REMOVAL SERVICE POINTS....3049
      INSTALLATION SERVICE POINTS....3050
      INSPECTION....3051
      BALL JOINT DUST COVER REPLACEMENT....3051
    LOWER ARM AND TORSION BAR....3052
      REMOVAL SERVICE POINT....3053
      INSTALLATION SERVICE POINTS....3054
      INSPECTION....3055
      REAR LOWER ARM BUSHING REPLACEMENT....3055
      FRONT LOWER ARM BUSHING REPLACEMENT....3056
      LOWER ARM BALL JOINT DUST COVER REPLACEMENT....3056
    STABILIZER BAR....3057
      INSTALLATION SERVICE POINT....3057
    SPECIFICATIONS....3058
GR00005900-34....3061
  REAR SUSPENSION....3061
    GENERAL DESCRIPTION....3062
    SPECIAL TOOLS....3063
    ON-VEHICLE SERVICE....3063
      REAR WHEEL ALIGNMENT CHECK AND ADJUSTMENT....3063
    LOWER ARM....3064
      LOWER ARM BUSHING REPLACEMENT....3065
    SHOCK ABSORBER AND LATERAL ROD....3066
      LATERAL ROD BUSHING REPLACEMENT....3067
    COIL SPRING AND AXLE BUMPER....3067
      INSTALLATION SERVICE POINTS....3068
    STABILIZER BAR....3069
      INSTALLATION SERVICE POINT....3069
    SPECIFICATIONS....3070
GR00006000-35....3071
  SERVICE BRAKES....3071
GR00006100-35A....3073
  BASIC BRAKE SYSTEM....3073
    GENERAL DESCRIPTION....3074
    BASIC BRAKE SYSTEM DIAGNOSIS....3074
      SYMPTOM PROCEDURES....3075
      INSPECTION PROCEDURE 1: Vehicle Pulls to One Side when Brakes are Applied...3075
        STEP 1. Check for oil, water, etc., on the pad or lining contact surface of all brakes...3075
        STEP 2. Check the lining and brake drum contact...3075
        STEP 3. Check the auto adjuster function...3075
        STEP 4. Check the brake drum inside diameter...3076
        STEP 5. Check disc brake pistons for smooth operation...3076
        STEP 6. Check brake disc(s) for run out...3076
        STEP 7. Check brake discs for correct thickness...3076
        STEP 8. Retest the system...3076
      INSPECTION PROCEDURE 2: Insufficient Braking Power....3077
        STEP 1. Check whether the brake fluid is low, is the correct fluid (A/T fluid, engine oil, etc.) ...3077
        STEP 2. Check for spongy (not firm brakes)...3077
        STEP 3. Check the lining and brake drum contact...3077
        STEP 4. Check the auto adjuster function...3077
        STEP 5. Check the brake booster function...3077
        STEP 6. Check for pinched or restricted brake tube or hose...3078
        STEP 7. Check for oil, water, etc., on the pad or lining contact surfaces of all brakes...3078
        STEP 8. Check the proportioning valve operation. <Vehicles without ABS>....3078
        STEP 9. Retest the system...3078
      INSPECTION PROCEDURE 3: Increased Pedal Stroke (Reduced Pedal-to-Floor Board Clearance)....3078
        STEP 1. Check for spongy (not firm brakes)...3078
        STEP 2. Check the pad or lining for wear...3078
        STEP 3. Check the vacuum hose and check valve for damage...3078
        STEP 4. Check the master cylinder function...3079
        STEP 5. Check for brake fluid leaks...3079
        STEP 6. Check the auto adjuster function...3079
        STEP 7. Check the clearance (too much) between the pushrod and primary piston...3079
        STEP 8. Retest the system...3079
      INSPECTION PROCEDURE 4: Brake Drag....3079
        STEP 1. Check the parking brake lever return...3079
        STEP 2. Check the parking brake pull amount...3079
        STEP 3. Check the brake pedal return spring for deterioration...3080
        STEP 4. Check the rear brake shoe springs for breakage...3080
        STEP 5. Check the amount of grease at each sliding section...3080
        STEP 6. Check the clearance (too low) between the pushrod and primary piston...3080
        STEP 7. Check the master cylinder piston return spring for damage and return port for clogging...3080
        STEP 8. Check port for clogging...3080
        STEP 9. Retest the system...3081
      INSPECTION PROCEDURE 5: Insufficient Parking Brake Function....3081
        STEP 1. Check the lining for wear...3081
        STEP 2. Check for oil or water, etc., on the lining contact surface...3081
        STEP 3. Check the parking brake cable...3081
        STEP 4. Check the auto adjuster function...3081
        STEP 5. Check the parking brake pull amount (excessive)...3081
        STEP 6. Retest the system...3081
      INSPECTION PROCEDURE 6: Scraping or Grinding Noise When Brakes are Applied...3082
        STEP 1. Check the front brakes, then rear brakes, for metal-to-metal condition...3082
        STEP 2. Check for interference between the caliper and wheel...3082
        STEP 3. Check for interference between the dust cover and brake disc...3082
        STEP 4. Check the brake drums for cracks...3082
        STEP 5. Check for bent backing plate(s)...3082
        STEP 6. Retest the system...3082
      INSPECTION PROCEDURE 7: Squealing, Groaning or Chattering Noise when Brakes are Applied...3083
        STEP 1. Check the brake drums and lining or brake disc and pads for wear or cutting...3083
        STEP 2. Check the calipers for rust...3083
        STEP 3. Check the lining parts for damage...3083
        STEP 4. Check whether the lining is dirty or greasy...3083
        STEP 5. Check whether the shoe hold-down springs are weak or the shoe-hold-down pins and springs ...3083
        STEP 6. Adjust the brake pedal or brake booster pushrod...3083
        STEP 7. Retest the system....3083
      INSPECTION PROCEDURE 8: Squealing Noise When Brakes are not Applied...3083
        DIAGNOSIS....3083
          STEP 1. Check whether the backing plate is bent or loose and interfering with the drum...3083
          STEP 2. Check whether the drum is damaged due to interference with the backing plate or shoe...3083
          STEP 3. Check the brake drum for wear and the shoe-to-shoe spring for damage...3084
          STEP 4. Check the brake discs for rust...3084
          STEP 5. Check the brake pads for correct installation...3084
          STEP 6. Check the calipers for correct installation...3084
          STEP 7. Check the wheel bearings for deterioration or damage, and the quality and quantity...3084
          STEP 8. Check whether the brake booster, master cylinder or wheel cylinder return is insufficient...3085
          STEP 9. Adjust the brake pedal or brake booster pushrod...3085
          STEP 10. Retest the system...3085
      INSPECTION PROCEDURE 9: Groaning, Clicking or Rattling Noise when Brakes are not Applied...3085
        STEP 1. Check whether foreign material has entered the wheel covers...3085
        STEP 2. Check for looseness of the wheel nuts...3085
        STEP 3. Check for looseness of the caliper installation bolt...3085
        STEP 4. Check the wheel bearings for wear, damage or dryness...3086
        STEP 5. Retest the system...3086
    SPECIAL TOOLS....3086
    ON-VEHICLE SERVICE....3087
      BRAKE PEDAL CHECK AND ADJUSTMENT....3087
      STOPLIGHT SWITCH CHECK....3088
      BRAKE BOOSTER OPERATING CHECK....3089
      CHECK VALVE OPERATION CHECK....3090
      PROPORTIONING VALVE FUNCTION TEST <VEHICLES WITHOUT ABS>....3090
      BLEEDING....3091
      BRAKE FLUID LEVEL SWITCH CHECK....3092
      DISC BRAKE PAD CHECK AND REPLACEMENT....3092
      FRONT BRAKE DISC RUN-OUT CHECK AND CORRECTION....3094
      BRAKE DISC THICKNESS CHECK....3095
      BRAKE LINING THICKNESS CHECK....3096
      BRAKE DRUM INSIDE DIAMETER CHECK....3096
      BRAKE LINING AND BRAKE DRUM CONTACT CHECK....3096
      AUTO ADJUSTER FUNCTION CHECK....3097
      MASTER CYLINDER FUNCTION CHECK....3098
    BRAKE PEDAL....3099
    MASTER CYLINDER ASSEMBLY AND BRAKE BOOSTER....3100
      INSTALLATION SERVICE POINTS....3101
      DISASSEMBLY SERVICE POINT....3102
      INSPECTION....3103
    FRONT DISC BRAKE ASSEMBLY....3103
      INSTALLATION SERVICE POINT....3104
      DISASSEMBLY SERVICE POINTS....3107
      ASSEMBLY SERVICE POINT....3108
      INSPECTION....3108
    REAR DRUM BRAKE....3109
      REMOVAL SERVICE POINT....3110
      INSTALLATION SERVICE POINTS....3110
      ASSEMBLY SERVICE POINT....3112
      INSPECTION....3112
    PROPORTIONING VALVE....3113
    SPECIFICATIONS....3114
GR00006200-35B....3117
  ANTI-LOCK BRAKING SYSTEM (ABS) <RWD>....3117
    GENERAL DESCRIPTION....3118
    ANTI-LOCK BRAKING SYSTEM (ABS) DIAGNOSIS....3119
      System Check Sound....3119
      ABS Operation Sounds and Sensations....3119
      Long Stopping Distances on Loose Road Surfaces....3119
      Shock at Starting Check....3119
      ABS Diagnostic Trouble Code Detection Conditions....3119
      DIAGNOSTIC FUNCTION....3120
        HOW TO CONNECT THE SCAN TOOL (MUT-III)....3120
        HOW TO READ AND ERASE DIAGNOSTIC TROUBLE CODE WITH SCAN TOOL (MUT-III)....3121
        HOW TO READ DIAGNOSTIC TROUBLE CODE WITH ABS WARNING LIGHT....3122
        HOW TO ERASE DIAGNOSTIC TROUBLE CODE WITH SPECIAL OPERATION FOR BRAKE PEDAL....3123
        HOW TO READ DATA LIST....3124
        HOW TO PERFORM ACTUATOR TEST....3124
      DIAGNOSTIC TROUBLE CODE PROCEDURES....3126
      DTC 11, 12, 13, 14: Wheel Speed Sensor (Open Circuit) DTC 21, 22, 23, 24: Wheel Speed Sensor....3126
        STEP 1. Check the wheel speed sensor installation...3128
        STEP 2. Measure the wheel speed sensor circuit resistance at ABS-ECU connector A-85...3128
        STEP 3. Check the harness wires between ABS-ECU connector A-85 (terminal No.20 and 21) and wheel ...3129
        STEP 4. Check the harness wires between ABS-ECU connector A-85 (terminal No.18 and 19) and wheel ...3129
        STEP 5. Check the harness wires between ABS-ECU connector A-85 (terminal No.1, 2, 3 and 4) and wh...3130
        STEP 6. Measure the wheel speed sensor output voltage...3131
        STEP 7. Check the wheel speed sensor or ABS rotor...3131
        STEP 8. Check the wheel bearing...3132
        STEP 9. Recheck for diagnostic trouble code...3132
      DTC 15: Wheel Speed Sensor (Abnormal Output Signal)....3132
        STEP 1. Check the wheel speed sensor installation...3133
        STEP 2. Check the harness wires between ABS-ECU connector A-85 (terminal No.20 and 21) and wheel ...3133
        STEP 3. Check the harness wires between ABS-ECU connector A-85 (terminal No.18 and 19) and wheel ...3134
        STEP 4. Check the harness wires between ABS-ECU connector A-85 (terminal No.1, 2, 3 and 4) and wh...3135
        STEP 5. Measure the wheel speed sensor output voltage...3136
        STEP 6. Check the wheel speed sensor or ABS rotor...3136
        STEP 7. Check the wheel bearing...3137
        STEP 8. Recheck for diagnostic trouble code...3137
      DTC 16: ABS-ECU Power Supply System....3138
        STEP 1. Check the battery...3139
        STEP 2. Measure the power supply circuit voltage at ABS-ECU connector A-85...3140
        STEP 3. Check the harness wires between connector D-08 (terminal No.2) and ABS-ECU connector A-85...3141
        STEP 4. Recheck for diagnostic trouble code...3142
      DTC 33 : Stoplight Switch System....3143
        STEP 1. Check the stoplight operation...3145
        STEP 2. Check the stoplight switch installation condition...3145
        STEP 3. Check the stoplight switch continuity...3145
        STEP 4. Using scan tool MB991958, check data list item 33: Stoplight switch...3145
        STEP 5. Measure the stoplight switch circuit at ABS-ECU connector A-85...3146
        STEP 6. Check the harness wire between ABS-ECU connector A-85 (terminal No.13) and stoplight swit...3147
        STEP 7. Check the harness wire between fusible link No.8 and stoplight switch connector C-66 (ter...3148
        STEP 8. Recheck for diagnostic trouble code...3149
      DTC 41, 42, 43 : Solenoid Valve inside Hydraulic Unit DTC 51: Hydraulic Unit Valve Relay Open or ...3150
        STEP 1. Measure the solenoid valve or motor power supply circuit at ABS-ECU connector A-86...3151
        STEP 2. Check the harness wire between fusible link number 14 and ABS-ECU connector A-86 (termina...3151
        STEP 3. Recheck for diagnostic trouble code...3152
      SYMPTOM PROCEDURES....3153
      INSPECTION PROCEDURE 1: Communication with Scan Tool is not Possible. (Communication with ABS Onl...3153
        STEP 1. Measure the power supply circuit at ABS-ECU connector A-85...3155
        STEP 2. Check the harness wire between ignition switch (IG2) and ABS-ECU connector A-85 (terminal...3155
        STEP 3. Check the harness wire between ABS-ECU connector A-85 (terminal No.23 and 24) and data li...3157
        STEP 4. Check the harness wires between ABS-ECU connector A-86 (terminal No.32 and 34) and ground...3158
        STEP 5. Retest the system...3158
      INSPECTION PROCEDURE 2: When the Ignition Switch is Turned to the "ON" Position (Engine Stopped o...3159
        STEP 1. Check the ABS warning light circuit at ABS-ECU connector A-85...3161
        STEP 2. Check the ABS relay...3161
        STEP 3. Check the ABS warning light circuit at ABS relay connector A-35...3162
        STEP 4. Check the ABS warning light bulb...3162
        STEP 5. Measure the combination meter for continuity...3162
        STEP 6. Measure the combination meter power supply circuit...3162
        STEP 7. Check connectors C-04, D-06 and D-08 for loose, corroded or damaged terminals, or termina...3163
        STEP 8. Check for continuity between the ignition switch (IG1) and the combination meter connecto...3163
        STEP 9. Check harness connectors A-35, C-05 and C-17 for loose, corroded or damaged terminals, or...3164
        STEP 10. Check the harness wire between ABS relay connector A-35 (terminal No. 3) and combination...3165
        STEP 11. Check ABS relay connector A-35 for loose, corroded or damaged terminals, or terminals pu...3165
        STEP 12. Check the harness wire between ABS relay connector A-35 (terminal No.4) and ground...3166
        STEP 13. Check ABS-ECU connector A-85 for loose, corroded or damaged terminals, or terminals push...3166
        STEP 14. Check the harness wire between ABS relay connector A-35 (terminal No.1) and ABS-ECU conn...3167
        STEP 15. Retest the system...3167
      INSPECTION PROCEDURE 3: The ABS Warning Light Remains Illuminated after the Engine is Started...3168
        STEP 1. Check the ABS warning light circuit at ABS relay connector A-35...3168
        STEP 2. Check harness connectors A-35, C-05 and C-17 for loose, corroded or damaged terminals, or...3169
        STEP 3. Check the harness wire between ABS relay connector A-35 (terminal No. 3) and combination ...3170
        STEP 4. Check the ABS relay...3170
        STEP 5. Check ABS relay connector A-35 and ABS-ECU connector A-85 for loose, corroded or damaged ...3171
        STEP 6. Check the harness wire between ABS relay connector A-35 (terminal No.1) and ABS-ECU conne...3171
        STEP 7. Retest the system...3172
      INSPECTION PROCEDURE 4: Brake Operation is Abnormal...3172
        ACTUATOR TEST SPECIFICATIONS....3173
    SPECIAL TOOLS....3176
    ON-VEHICLE SERVICE....3177
      BLEEDING....3177
        BLEEDING THE MASTER CYLINDER....3177
        BLEEDING THE BRAKE LINE....3177
      WHEEL SPEED SENSOR OUTPUT VOLTAGE MEASUREMENT....3178
      HYDRAULIC UNIT CHECK....3179
      ABS RELAY CHECK....3182
      DISCHARGED BATTERY....3182
    MASTER CYLINDER AND BRAKE BOOSTER....3183
      DISASSEMBLY SERVICE POINT....3184
      INSPECTION....3184
    HYDRAULIC UNIT....3185
      REMOVAL SERVICE POINTS....3185
      INSTALLATION SERVICE POINT....3186
    WHEEL SPEED SENSOR....3187
      REMOVAL SERVICE POINT....3188
      INSPECTION....3188
    SPECIFICATIONS....3189
GR00006300-35C....3191
  ANTI-LOCK BRAKING SYSTEM (ABS) <4WD>....3191
    GENERAL DESCRIPTION....3192
    ANTI-LOCK BRAKING SYSTEM (ABS) DIAGNOSIS....3194
      System Check Sound....3194
      ABS Operation Sounds and Sensations....3194
      Long Stopping Distances on Loose Road Surfaces....3194
      Shock at Starting Check....3194
      ABS Diagnostic Trouble Code Detection Conditions....3194
      DIAGNOSTIC FUNCTION....3195
        HOW TO CONNECT THE SCAN TOOL (MUT-III)....3195
        HOW TO READ AND ERASE DIAGNOSTIC TROUBLE CODE WITH SCAN TOOL (MUT-III)....3196
        HOW TO READ DIAGNOSTIC TROUBLE CODE WITH ABS WARNING LIGHT....3197
        HOW TO ERASE DIAGNOSTIC TROUBLE CODE WITH SPECIAL OPERATION FOR BRAKE PEDAL....3198
        HOW TO READ DATA LIST....3199
        HOW TO PERFORM ACTUATOR TEST....3200
      DIAGNOSTIC TROUBLE CODE PROCEDURES....3202
      DTC 11, 12, 13, 14: Wheel Speed Sensor (Open Circuit) DTC 21, 22, 23, 24: Wheel Speed Sensor....3202
        STEP 1. Check the wheel speed sensor installation...3204
        STEP 2. Measure wheel speed sensor circuit resistance at ABS-ECU connector A-85...3204
        STEP 3. Check the harness wires between ABS-ECU connector A-85 (terminal No.20 and 21) and wheel ...3205
        STEP 4. Check the harness wires between ABS-ECU connector A-85 (terminal No.18 and 19) and wheel ...3205
        STEP 5. Check the harness wires between ABS-ECU connector A-85 (terminal No.1, 2, 3 and 4) and wh...3206
        STEP 6. Measure the wheel speed sensor output voltage...3207
        STEP 7. Check the wheel speed sensor or ABS rotor...3207
        STEP 8. Check the wheel bearing...3208
        STEP 9. Recheck for diagnostic trouble code...3208
      DTC 15: Wheel Speed Sensor (Abnormal Output Signal)....3208
        STEP 1. Check the wheel speed sensor installation...3209
        STEP 2. Check the harness wires between ABS-ECU connector A-85 (terminal No.20 and 21) and wheel ...3209
        STEP 3. Check the harness wires between ABS-ECU connector A-85 (terminal No. 18 and 19) and wheel...3210
        STEP 4. Check the harness wires between ABS-ECU connector A-85 (terminal No.1, 2, 3 and 4) and wh...3211
        STEP 5. Measure the wheel speed sensor output voltage...3212
        STEP 6. Check the wheel speed sensor or ABS rotor...3212
        STEP 7. Check the wheel bearing...3213
        STEP 8. Recheck for diagnostic trouble code...3213
      DTC 16: ABS-ECU Power Supply System....3214
        STEP 1. Check the battery...3215
        STEP 2. Measure the power supply circuit voltage at ABS-ECU connector A-85...3216
        STEP 3. Check the harness wires between connector D-08 (terminal No.2) and ABS-ECU connector A-85...3217
        STEP 4. Recheck for diagnostic trouble code...3218
      DTC 25: 2/4WD Switch 1 DTC 26: 2/4WD Switch 2....3219
        STEP 1. Using scan tool MB991958, read the diagnostic trouble code...3220
        STEP 2. Check the following connectors...3221
        STEP 3. Check the following harness wire...3221
        STEP 4. Check the following connectors...3222
        STEP 5. Check the following harness wire...3223
        STEP 6. Recheck for diagnostic trouble code...3223
      DTC 32: G-sensor System....3224
        STEP 1. Using scan tool MB991958, check data list item 32: G-sensor output voltage...3226
        STEP 2. Measure the power supply circuit voltage at G-sensor connector C-26...3226
        STEP 3. Check the ground circuit at G-sensor connector C-26...3227
        STEP 4. Measure the output circuit voltage at G-sensor connector C-26...3227
        STEP 5. Check the harness wire between G-sensor connector C-26 (terminal No.1) and ignition switc...3228
        STEP 6. Check the harness wires between G-sensor connector C-26 (terminal No.2 and 3) and ABS-ECU...3229
        STEP 7. Recheck for diagnostic trouble code...3230
      DTC 33 : Stoplight Switch System....3231
        STEP 1. Check the stoplight operation...3233
        STEP 2. Check the stoplight switch installation condition...3233
        STEP 3. Check the stoplight switch continuity...3233
        STEP 4. Using scan tool MB991958, check data list item 33: Stoplight switch...3233
        STEP 5. Measure the stoplight switch circuit at ABS-ECU connector A-85...3234
        STEP 6. Check the harness wire between ABS-ECU connector A-85 (terminal No.13) and stoplight swit...3235
        STEP 7. Check the harness wire between fusible link No.8 and stoplight switch connector C-66 (ter...3236
        STEP 8. Recheck for diagnostic trouble code...3237
      DTC 41, 42, 43 : Solenoid Valve inside Hydraulic Unit DTC 51: Hydraulic Unit Valve Relay Open or ...3238
        STEP 1. Measure the solenoid valve or motor power supply circuit at ABS-ECU connector A-86...3239
        STEP 2. Check the harness wire between fusible link number 14 and ABS-ECU connector A-86 (termina...3239
        STEP 3. Recheck for diagnostic trouble code...3240
      SYMPTOM PROCEDURES....3241
      INSPECTION PROCEDURE 1: Communication with Scan Tool is not Possible. (Communication with ABS Onl...3241
        STEP 1. Measure the power supply circuit at ABS-ECU connector A-85...3243
        STEP 2. Check the harness wire between ignition switch (IG2) and ABS-ECU connector A-85 (terminal...3243
        STEP 3. Check the harness wire between ABS-ECU connector A-85 (terminal No.23 and 24) and data li...3245
        STEP 4. Check the harness wires between ABS-ECU connector A-86 (terminal No.32 and 34) and ground...3246
        STEP 5. Retest the system...3246
      INSPECTION PROCEDURE 2: When the Ignition Switch is Turned to the "ON" Position (Engine Stopped o...3247
        STEP 1. Check the ABS warning light circuit at ABS-ECU connector A-85...3249
        STEP 2. Check the ABS relay...3249
        STEP 3. Check the ABS warning light circuit at ABS relay connector A-35...3250
        STEP 4. Check the ABS warning light bulb...3250
        STEP 5. Measure the combination meter for continuity...3250
        STEP 6. Measure the combination meter power supply circuit...3250
        STEP 7. Check connectors C-04, D-06 and D-08 for loose, corroded or damaged terminals, or termina...3251
        STEP 8. Check for continuity between the ignition switch (IG1) and the combination meter connecto...3251
        STEP 9. Check harness connectors A-35, C-05 and C-17 for loose, corroded or damaged terminals, or...3252
        STEP 10. Check the harness wire between ABS relay connector A-35 (terminal No. 3) and combination...3253
        STEP 11. Check ABS relay connector A-35 for loose, corroded or damaged terminals, or terminals pu...3253
        STEP 12. Check the harness wire between ABS relay connector A-35 (terminal No.4) and ground...3254
        STEP 13. Check ABS-ECU connector A-85 for loose, corroded or damaged terminals, or terminals push...3254
        STEP 14. Check the harness wire between ABS relay connector A-35 (terminal No.1) and ABS-ECU conn...3255
        STEP 15. Retest the system...3255
      INSPECTION PROCEDURE 3: The ABS Warning Light Remains Illuminated after the Engine is Started...3256
        STEP 1. Check the ABS warning light circuit at ABS relay connector A-35...3256
        STEP 2. Check harness connectors A-35, C-05 and C-17 for loose, corroded or damaged terminals, or...3257
        STEP 3. Check the harness wire between ABS relay connector A-35 (terminal No. 3) and combination ...3258
        STEP 4. Check the ABS relay...3258
        STEP 5. Check ABS relay connector A-35 and ABS-ECU connector A-85 for loose, corroded or damaged ...3259
        STEP 6. Check the harness wire between ABS relay connector A-35 (terminal No.1) and ABS-ECU conne...3259
        STEP 7. Retest the system...3260
      INSPECTION PROCEDURE 4: Brake Operation is Abnormal...3260
        ACTUATOR TEST SPECIFICATIONS....3262
    SPECIAL TOOLS....3265
    ON-VEHICLE SERVICE....3266
      BLEEDING....3266
      WHEEL SPEED SENSOR OUTPUT VOLTAGE MEASUREMENT....3266
      HYDRAULIC UNIT CHECK....3266
      ABS RELAY CHECK....3266
      DISCHARGED BATTERY....3266
    MASTER CYLINDER AND BRAKE BOOSTER....3266
      INSPECTION....3266
    HYDRAULIC UNIT....3266
    WHEEL SPEED SENSOR....3267
      INSPECTION....3267
    G-SENSOR....3267
      G-SENSOR CHECK....3267
    SPECIFICATIONS....3268
GR00006400-36....3269
  PARKING BRAKES....3269
    GENERAL INFORMATION....3270
    ON-VEHICLE SERVICE....3270
      PARKING BRAKE LEVER STROKE CHECK....3270
      PARKING BRAKE SWITCH CHECK....3271
    PARKING BRAKE LEVER....3272
    PARKING BRAKE CABLE....3273
    SPECIFICATIONS....3273
GR00006500-37A....3275
  STEERING....3275
    GENERAL DESCRIPTION....3277
    POWER STEERING DIAGNOSIS....3278
      SYMPTOM PROCEDURES....3279
      INSPECTION PROCEDURE 1: Excessive Play of Steering Wheel....3279
        STEP 1. Check for looseness at the steering shaft coupling section and at the steering linkage...3279
        STEP 2. Check the steering gear backlash (excessive)...3279
        STEP 3. Check steering wheel play...3279
      INSPECTION PROCEDURE 2: Difficult Steering Wheel Operation (Insufficient Power Assist)....3280
        STEP 1. Check the power steering belt tension...3280
        STEP 2. Check the belt for damage...3280
        STEP 3. Check the fluid level...3280
        STEP 4. Check for entry of air...3280
        STEP 5. Check each hose for crushing or twisting...3280
        STEP 6. Check for oil leaks...3280
        STEP 7. Check the wheel alignment (camber and caster)...3281
        STEP 8. Check the gear box rack piston seal for damage...3281
        STEP 9. Check for excessive tie rod end ball joint breakaway torque...3281
        STEP 10. Check steering wheel operation...3281
      INSPECTION PROCEDURE 3: Rattling Noise....3281
        STEP 1. Check for proper oil pump and gear box installation...3281
        STEP 2. Check for interference of other parts with the steering column and power steering hoses...3281
        STEP 3. Check for noise from inside the oil pump or gear box...3281
        STEP 4. Check for rattling noise...3281
      INSPECTION PROCEDURE 4 : Shrill Noise....3282
        STEP 1. Check for entry of air...3282
        STEP 2. Check for seizure in the oil pump...3282
        STEP 3. Retest the system...3282
      INSPECTION PROCEDURE 5 : Squealing Noise....3282
        STEP 1. Check the belt tension...3282
        STEP 2. Check for seizure in the oil pump...3282
        STEP 3. Retest the system...3282
      INSPECTION PROCEDURE 6 : Hissing Noise....3282
        STEP 1. Check for entry of air...3282
        STEP 2. Check each hose for crushing or twisting...3282
        STEP 3. Check the steering box for damage...3282
        STEP 4. Retest the system...3282
      INSPECTION PROCEDURE 7 : Droning Noise....3283
        STEP 1. Check the oil pump or oil pump bracket installation...3283
        STEP 2. Check the oil pump for damage...3283
        STEP 3. Retest the system...3283
      INSPECTION PROCEDURE 8: Squeaking Noise....3284
        STEP 1. Check for interference of the wheel and vehicle body...3284
        STEP 2. Check the steering gear box for damage...3284
        STEP 3. Retest the system...3284
      INSPECTION PROCEDURE 9: Vibration....3285
        STEP 1. Check for entry of air...3285
        STEP 2. Check the steering gear box for damage...3285
        STEP 3. Retest the system...3285
      INSPECTION PROCEDURE 10: Oil Leakage from Hose Connection....3285
        STEP 1. Check for loosening of the flare nut...3285
        STEP 2. Check the hose connection and the clamp installation...3285
        STEP 3. Retest the system...3285
      INSPECTION PROCEDURE 11 : Oil Leakage from Hose Assembly....3285
        STEP 1. Check the hose for damage or clogging...3285
        STEP 2. Retest the system...3285
      INSPECTION PROCEDURE 12: Oil Leakage from Oil Reservoir....3286
        STEP 1. Check the oil reservoir for damage...3286
        STEP 2. Check for overflowing...3286
        STEP 3. Retest the system...3286
      INSPECTION PROCEDURE 13 : Oil Leakage from Oil Pump....3286
        STEP 1. Check the oil pump body for damage...3286
        STEP 2. Check the O-ring or oil seal for damage...3286
        STEP 3. Retest the system...3286
      INSPECTION PROCEDURE 14 : Oil Leakage from Gear Box....3286
        STEP 1. Check the gear box housing for damage...3286
        STEP 2. Check the oil-ring or oil seal for damage...3286
        STEP 3. Retest the system...3286
    SPECIAL TOOLS....3287
    ON-VEHICLE SERVICE....3289
      STEERING WHEEL FREE PLAY CHECK....3289
      STEERING ANGLE CHECK....3290
      STEERING GEAR BACKLASH CHECK....3290
      TIE ROD END BALL JOINT VARIATION CHECK (SHAFT DIRECTION)....3291
      TIE ROD END BALL JOINT BREAKAWAY TORQUE CHECK....3291
      STATIONARY STEERING EFFORT CHECK....3292
      STEERING WHEEL RETURN TO CENTER CHECK....3293
      DRIVE BELT TENSION CHECK....3293
      FLUID LEVEL CHECK....3293
      POWER STEERING FLUID REPLACEMENT....3294
      POWER STEERING SYSTEM AIR BLEEDING....3294
      OIL PUMP PRESSURE TEST....3295
      POWER STEERING PRESSURE SWITCH CHECK....3296
      BALL JOINT DUST COVER INSPECTION....3297
      STEERING COLUMN SHAFT ASSEMBLY SHOCK ABSORBING MECHANISM CHECK....3297
        INSPECTION PROCEDURE....3298
    STEERING WHEEL AND SHAFT ASSEMBLY....3299
      REMOVAL SERVICE POINTS....3300
      INSTALLATION SERVICE POINTS....3301
      DISASSEMBLY SERVICE POINT....3302
      ASSEMBLY SERVICE POINTS....3303
    POWER STEERING GEAR BOX ASSEMBLY....3304
      REMOVAL SERVICE POINT....3305
      INSTALLATION SERVICE POINT....3305
      INSPECTION....3306
      PITMAN ARM DUST COVER CHECK....3306
        DISASSEMBLY SERVICE POINTS....3308
        ASSEMBLY SERVICE POINTS....3311
      POWER STEERING GEAR BOX ASSEMBLY INSPECTION (DISASSEMBLY AND REASSEMBLY)....3313
      DUST COVER REPLACEMENT....3313
    POWER STEERING OIL PUMP ASSEMBLY....3314
      INSPECTION....3314
        DISASSEMBLY SERVICE POINT....3316
        ASSEMBLY SERVICE POINTS....3316
      INSPECTION....3318
    POWER STEERING HOSES....3319
      INSTALLATION SERVICE POINTS....3320
    STEERING LINKAGE....3322
      REMOVAL SERVICE POINT....3323
      INSTALLATION SERVICE POINTS....3323
      INSPECTION....3324
        DUST COVER CHECK....3324
        ASSEMBLY SERVICE POINT....3325
      INSPECTION....3325
        IDLER ARM SLIDING RESISTANCE....3325
        DUST COVER REPLACEMENT....3326
    SPECIFICATIONS....3327
INDEX....3331

Mitsubishi Pajero Models Repair Service Manual 2010-2012