Mitsubishi Mirage, Galant, Diamant Repair Service Manual 1990-2000
Complete service repair manual with Electrical Wiring Diagrams for Mitsubishi Mirage, Galant, Diamant 1990-2000, with all the technical information to maintain, diagnose, repair, and rebuild like professional mechanics.
Mitsubishi Mirage, Galant, Diamant 1990-2000 workshop service repair manual includes:
* Numbered table of contents easy to use so that you can find the information you need fast.
* Detailed sub-steps expand on repair procedure information
* Numbered instructions guide you through every repair procedure step by step.
* Troubleshooting and electrical service procedures are combined with detailed wiring diagrams for ease of use.
* Notes, cautions and warnings throughout each chapter pinpoint critical information.
* Bold figure number help you quickly match illustrations with instructions.
* Detailed illustrations, drawings and photos guide you through every procedure.
* Enlarged inset helps you identify and examine parts in detail.
PRODUCT DETAILS:
Total Pages: 5,811 pages
File Format: PDF / ISO disc image
Language: English
TABLE OF CONTENTS
'90-'00 Mirage, Galant, Diamant....1
Cover....1
1 General info & maintenance....6
2 Engine Electrical....53
3 Engine Mechanical....67
4 Driveability & Emissions....149
5 Fuel system....193
6 Chassis Electrical....209
7 Drivetrain....285
8 Suspension & Steering....301
9 Brakes....342
10 Body and Trim....374
11 Troubleshooting....388
Glossary & Index....404
'99- Mirage....414
Vol. 1....414
00 General....414
00E General Electrical....467
11A 1.5L engine....479
11B 1.5L overhaul....513
11C 1.8L engine....564
11D 1.8L overhaul....596
12 Engine Lubrication....651
13A MFI 1.5L....655
13B MFI 1.8L....819
13C Fuel Supply....976
14 Engine Cooling....981
15 Intake and Exhaust....997
16 Engine Electrical....1006
17 Engine & Emission control....1056
21A Clutch....1105
21B Clutch Overhaul....1117
22A Manual Transaxle....1125
22B Manual Trans Overhaul....1139
23A Automatic Transaxle....1200
23B Auto Trans Overhaul....1281
Index....1356
Vol. 2....1362
26 Front axle....1362
27 Rear axle....1382
31 Wheels and tires....1388
32 Power plant mount....1393
33A Front Suspension....1402
34 Rear suspension....1415
35A Basic Brake system....1428
35B Anti lock braking....1460
36 Parking Brakes....1501
37A Steering....1507
42 Body....1546
51 Exterior....1601
52A Interior....1622
52B SRS....1648
54 Chassis Electrical....1687
55 HVAC....1757
70 Component Locations....1790
80A Configuration Diagrams....1808
80B Splice Locations....1832
90 Circuit diagrams....1843
Index....1956
Table of contents....1962
Tach hookup....1964
-'16....1966
14_EL_MMNA_BRM_PDF....1966
GR00000100-1....1966
BODY CONSTRUCTION....1966
BODY COMPONENTS....1967
BODY MAIN CROSS-SECTIONAL VIEWS....1969
MAINTENANCE, SERVICEABILITY....1971
FENDER SHIELD....1971
SIDE STRUCTURE....1971
SIDE OUTER PANEL....1972
BODY CONSTRUCTION CHARACTERISTICS....1973
HEADLIGHT SUPPORT....1973
FRONT SIDEMEMBER REINFORCEMENT....1974
FRONT DECK....1977
DASH PANEL....1977
SIDE STRUCTURE....1978
SIDE STRUCTURE REINFORCEMENT....1979
FRONT FLOOR....1981
REAR FLOOR....1982
REAR FLOOR SIDEMEMBER REINFORCEMENT....1983
SILENCER APPLICATION LOCATIONS....1986
URETHANE FOAM USAGE LOCATIONS....1988
GR00000200-2....1989
BODY DIMENSIONS....1989
BODY DIMENSIONS AND MEASUREMENT METHODS....1990
TYPE A (PROJECTED DIMENSIONS)....1992
TYPE B (ACTUAL-MEASUREMENT DIMENSIONS)....1995
GR00000300-3....2009
WELDED PANEL REPLACEMENT....2009
ULTRA HIGH STRENGTH STEEL PLATE....2010
ADVANTAGES OF ULTRA HIGH STRENGTH STEEL PLATE....2010
PRECAUTION UPON MAINTENANCE OF ULTRA HIGH STRENGTH STEEL PLATE....2010
FENDER SHIELD....2011
FRONT SIDEMEMBER (PARTIAL REPLACEMENT)....2014
FRONT PILLAR....2015
NOTE ON REPAIR WORK....2017
FRONT PILLAR (PARTIAL REPLACEMENT)....2018
NOTE ON REPAIR WORK....2019
CENTER PILLAR....2021
NOTE ON REPAIR WORK....2023
SIDE SILL....2024
NOTE ON REPAIR WORK....2025
QUARTER OUTER....2027
NOTE ON REPAIR WORK....2028
REAR END PANEL....2029
REAR FLOOR....2030
NOTE ON REPAIR WORK....2032
ROOF....2033
QUARTER INNER....2034
QUARTER INNER LOWER....2036
FRONT DOOR OUTER PANEL (WELDED TYPE)....2037
FRONT DOOR OUTER PANEL (ADHESION TYPE)....2038
NOTE ON REPAIR WORK....2038
REAR DOOR OUTER PANEL (WELDED TYPE)....2039
REAR DOOR OUTER PANEL (ADHESION TYPE)....2040
NOTE ON REPAIR WORK....2040
FRONT END CROSSMEMBER....2041
GR00000400-4....2043
CORROSION PROTECTION....2043
BODY SEALING LOCATIONS....2044
FLOOR....2044
UPPER BODY....2045
SIDE BODY....2045
UNDERCOAT APPLICATION LOCATIONS....2049
GR00000500-5....2051
SYNTHETIC-RESIN PARTS....2051
LOCATION OF SYNTHETIC-RESIN PARTS....2052
GR00000600-6....2055
BODY COLOR....2055
BODY COLOR CODE....2056
BODY COLOR CHARTS....2056
GR00000700-9....2057
BASE OF BODY REPAIR....2057
GENERAL....2058
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)....2058
WELDING....2059
FUSION WELDING....2059
PRESSURE WELDING....2059
BRAZING....2059
ADVANTAGES OF ELECTRIC RESISTANCE SPOT WELDING....2059
PLUG WELDING....2067
CONTINUOUS WELDING....2068
NOTES REGARDING MIG WELDING....2069
BRAZING....2069
Notes with regard to brazing work....2069
GAS WELDING....2070
BODY REPAIR....2071
STANDARD PROCEDURES FOR REPLACEMENT OF WELDED PANELS....2071
CAUTIONS REGARDING BODY REPAIR....2078
THEFT PROTECTION....2080
PANEL REPAIR CAUTION....2080
HOW TO PEEL OFF THE SURFACE MASKING FILM FROM THE THEFT-PROTECTION LABEL....2080
REPAIRS USING A HAMMER AND DOLLY....2083
OVERALL ROUGH REPAIRS....2084
FRAME STRAIGHTENING NOTES....2085
CHECKING FOR FRAME CRACKING OR FLAKING....2085
REPAIRING CRACKS....2086
NOTES REGARDING REPAIR WORK....2088
SAFETY MEASURES....2088
HEALTH AND SANITATION PROCEDURES....2090
VEHICLE PROTECTION....2090
CORROSION PROTECTION....2094
ZINC PHOSPHATE COATING....2094
BODY SEALING....2095
UNDERBODY COATING....2095
WAX INJECTION....2096
SEALING TAPE....2096
ANTICORROSION TREATMENT AT THE TIME OF BODY REPAIR WORK....2097
CORROSION PROTECTION FOR HOLLOW PARTS....2097
ANTICORROSION TREATMENT OF ROUGH CUTS....2097
SPOT SEALER....2097
BODY SEALING....2099
REPAIR OF SYNTHETIC-RESIN PARTS....2101
REPAIR JUDGMENT....2102
REPAIR PROCEDURE....2102
Manual description_BRM....2107
PrefaceForBRM_MMNA....2108
15_EL_MMNA_PDF....2110
GR00000100-11....2110
ENGINE....2110
GR00000200-11A....2112
ENGINE MECHANICAL....2112
GENERAL INFORMATION....2113
ENGINE DIAGNOSIS....2113
SERVICE SPECIFICATIONS....2114
SPECIAL TOOLS....2115
ON-VEHICLE SERVICE....2119
DRIVE BELT TENSION CHECK AND ADJUSTMENT....2119
DRIVE BELT TENSION CHECK....2119
DRIVE BELT TENSION ADJUSTMENT....2121
IGNITION TIMING CHECK....2122
IDLE SPEED CHECK....2123
IDLE MIXTURE CHECK....2123
VALVE CLEARANCE CHECK AND ADJUSTMENT....2124
COMPRESSION PRESSURE CHECK....2127
MANIFOLD VACUUM CHECK....2128
CRANKSHAFT PULLEY....2129
REMOVAL SERVICE POINTS....2129
INSTALLATION SERVICE POINT....2131
ROCKER COVER ASSEMBLY....2133
INSTALLATION SERVICE POINT....2133
CAMSHAFT....2134
REMOVAL SERVICE POINTS....2135
INSTALLATION SERVICE POINTS....2138
OIL FEEDER CONTROL VALVE....2140
VALVE STEM SEAL....2141
REMOVAL SERVICE POINTS....2142
INSTALLATION SERVICE POINTS....2143
OIL PAN....2148
REMOVAL SERVICE POINTS....2148
INSTALLATION SERVICE POINT....2149
INSPECTION....2149
CRANKSHAFT OIL SEAL....2150
<M/T>....2150
<CVT>....2151
REMOVAL SERVICE POINT....2151
INSTALLATION SERVICE POINTS....2151
CYLINDER HEAD GASKET....2153
REMOVAL SERVICE POINT....2153
INSTALLATION SERVICE POINTS....2154
TIMING CHAIN CASE ASSEMBLY....2155
REMOVAL SERVICE POINTS....2156
INSTALLATION SERVICE POINTS....2156
TIMING CHAIN....2156
ENGINE ASSEMBLY....2157
REMOVAL SERVICE POINTS....2159
INSTALLATION SERVICE POINTS....2160
GR00000200-80A....2162
CONFIGURATION DIAGRAMS....2162
OVERALL CONFIGURATION DIAGRAM....2163
HOW TO READ CONFIGURATION DIAGRAMS....2164
ENGINE COMPARTMENT....2165
ENGINE AND TRANSAXLE....2169
INSTRUMENT PANEL....2173
FLOOR....2181
ROOF....2183
DOOR....2184
LIFTGATE....2186
GR00000300-11B....2188
ENGINE OVERHAUL....2188
GENERAL SPECIFICATIONS....2189
SERVICE SPECIFICATIONS....2189
REWORK DIMENSIONS....2190
TORQUE SPECIFICATIONS....2191
SEALANTS AND ADHESIVES....2193
SPECIAL TOOLS....2195
GENERATOR AND IGNITION SYSTEM....2197
REMOVAL SERVICE POINT....2198
INSTALLATION SERVICE POINTS....2198
FUEL AND EMISSION PARTS....2200
REMOVAL SERVICE POINT....2201
INSTALLATION SERVICE POINTS....2201
INTAKE MANIFOLD....2203
INSTALLATION SERVICE POINTS....2203
EXHAUST MANIFOLD....2204
REMOVAL SERVICE POINT....2205
INSTALLATION SERVICE POINT....2205
WATER HOSE AND PIPE....2206
INSTALLATION SERVICE POINTS....2207
OIL PAN AND TIMING CHAIN CASE....2210
REMOVAL SERVICE POINTS....2211
INSTALLATION SERVICE POINTS....2212
TIMING CHAIN....2217
REMOVAL SERVICE POINTS....2218
INSTALLATION SERVICE POINTS....2220
INSPECTION....2223
CAMSHAFT....2227
REMOVAL SERVICE POINTS....2228
INSTALLATION SERVICE POINTS....2228
INSPECTION....2230
CYLINDER HEAD AND VALVES....2232
REMOVAL SERVICE POINTS....2233
INSTALLATION SERVICE POINTS....2233
INSPECTION....2238
REPAIR PROCEDURE OF VALVE SEAT....2240
REPLACEMENT PROCEDURE OF VALVE SEAT....2240
REPLACEMENT PROCEDURE OF VALVE GUIDE....2241
PISTON AND CONNECTING ROD....2242
REMOVAL SERVICE POINTS....2243
INSTALLATION SERVICE POINTS....2244
INSPECTION....2248
CRANKSHAFT AND CYLINDER BLOCK....2250
REMOVAL SERVICE POINT....2251
INSTALLATION SERVICE POINTS....2251
INSPECTION....2256
GR00000300-90....2258
CIRCUIT DIAGRAMS....2258
HOW TO READ CIRCUIT DIAGRAMS....2261
WIRE COLOR CODES....2266
JUNCTION BLOCK....2267
JOINT CONNECTOR....2269
CENTRALIZED JUNCTION....2277
FUSIBLE LINK AND FUSE....2277
POWER DISTRIBUTION SYSTEM....2285
STARTING SYSTEM <M/T>....2297
STARTING SYSTEM <CVT>....2299
IGNITION SYSTEM....2301
CHARGING SYSTEM....2303
MFI SYSTEM....2305
COOLING SYSTEM....2315
SHIFT LOCK MECHANISM <CVT>....2317
CVT....2319
HEADLIGHT....2327
TAILLIGHT, POSITION LIGHT, SIDE MARKER LIGHT, LICENSE PLATE LIGHT AND LIGHTING MONITOR TONE ALARM....2333
FOG LIGHT....2339
DOME LIGHT AND LUGGAGE COMPARTMENT LIGHT....2343
TURN-SIGNAL LIGHT AND HAZARD WARNING LIGHT....2349
BACKUP LIGHT....2354
STOPLIGHT....2355
HORN....2356
METER AND GAUGE....2357
BRAKE WARNING LIGHT, FUEL WARNING LIGHT AND OIL PRESSURE WARNING LIGHT....2361
POWER WINDOWS <VEHICLES WITHOUT SAFETY SYSTEM>....2365
POWER WINDOWS <VEHICLES WITH SAFETY SYSTEM>....2369
CENTRAL DOOR LOCKING SYSTEM....2375
PTC HEATER....2385
HEATER....2389
MANUAL AIR CONDITIONING SYSTEM....2391
AUTOMATIC AIR CONDITIONING SYSTEM....2397
WINDSHIELD WIPER AND WASHER....2403
REAR WIPER AND WASHER....2407
REAR WINDOW DEFOGGER AND DOOR MIRROR HEATER <VEHICLES WITHOUT AUTOMATIC AIR CONDITIONING SYSTEM>....2411
REAR WINDOW DEFOGGER AND DOOR MIRROR HEATER <VEHICLES WITH AUTOMATIC AIR CONDITIONING SYSTEM>....2415
REMOTE CONTROLLED DOOR MIRROR....2418
AUDIO SYSTEM....2419
MITSUBISHI MULTI ENTERTAINMENT SYSTEM (MMES)....2425
HANDS-FREE INTERFACE SYSTEM <VEHICLES WITHOUT MMES>....2433
ACCESSORY SOCKET....2437
ANTI-LOCK BRAKING SYSTEM (ABS), ACTIVE STABILITY CONTROL SYSTEM (ASC) AND HILL START ASSIST SYSTEM (HSA)....2439
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)....2445
ELECTRIC POWER STEERING SYSTEM....2453
IMMOBILIZER SYSTEM <VEHICLES WITHOUT KOS>....2455
STEERING LOCK <VEHICLES WITHOUT KOS (CVT)>....2457
ONE TOUCH START SYSTEM....2459
CRUISE CONTROL SYSTEM....2469
TIRE PRESSURE MONITORING SYSTEM (TPMS)....2475
PANIC ALARM....2479
HEATED SEAT....2485
IGNITION KEY REMINDER TONE ALARM <VEHICLES WITHOUT KOS>....2489
DOOR AJAR WARNING TONE ALARM....2491
SEAT BELT WARNING TONE ALARM....2495
PARKING BRAKE REMINDER TONE ALARM....2499
SPARE CONNECTOR....2501
CONTROLLER AREA NETWORK (CAN)....2503
GR00000400-12....2506
ENGINE LUBRICATION....2506
GENERAL INFORMATION....2507
ENGINE OILS....2507
SERVICE SPECIFICATIONS....2507
SEALANT....2507
LUBRICANTS....2508
SPECIAL TOOLS....2509
ON-VEHICLE SERVICE....2509
ENGINE OIL CHECK....2509
ENGINE OIL CHANGE....2509
OIL FILTER REPLACEMENT....2510
OIL FILTER STUD REPLACEMENT....2511
ENGINE OIL PRESSURE CHECK....2512
ENGINE OIL PRESSURE SWITCH....2512
REMOVAL SERVICE POINT....2513
INSTALLATION SERVICE POINT....2513
GR00000500-13....2514
FUEL....2514
GR00000700-13B....2516
FUEL SUPPLY....2516
SERVICE SPECIFICATIONS....2517
FUEL SUPPLY DIAGNOSIS....2517
Inspection Procedure 1 : Engine Malfunctions Due to Insufficient Fuel Supply....2517
DIAGNOSIS....2518
STEP 1. Using scan tool (M.U.T.-III), read the MFI system diagnostic trouble code.....2518
STEP 2. Check the fuel pressure.....2518
STEP 3. Check for bending, twisting or clogging of the fuel main pipe and fuel high-pressure tube.....2518
STEP 4. Check the fuel pump module operation.....2518
STEP 5. Check the inside of the fuel tank for contamination and rust.....2519
STEP 6. Retest the system.....2519
SPECIAL TOOLS....2520
ON-VEHICLE SERVICE....2522
FUEL PUMP OPERATION CHECK....2522
FUEL LEVEL SENSOR CHECK....2522
FUEL PUMP MODULE REPLACEMENT....2522
FUEL TANK DIFFERENTIAL PRESSURE SENSOR CHECK....2524
FUEL TANK TEMPERATURE SENSOR CHECK....2525
LEVELING VALVE CHECK....2526
FUEL TANK....2527
REMOVAL SERVICE POINTS....2527
INSTALLATION SERVICE POINT....2529
DISASSEMBLY SERVICE POINTS....2530
ASSEMBLY SERVICE POINTS....2531
ASSEMBLY SERVICE POINT....2533
FUEL FILLER NECK....2533
GR00000800-14....2534
ENGINE COOLING....2534
SERVICE SPECIFICATIONS....2535
LUBRICANTS....2535
ENGINE COOLING DIAGNOSIS....2535
SYMPTOM PROCEDURES....2536
Inspection Procedure 1: Coolant Leak....2536
DIAGNOSIS....2536
STEP 1. Check for coolant leaks.....2536
STEP 2. Retest the system.....2536
Inspection Procedure 2: Engine Overheating....2536
DIAGNOSIS....2536
STEP 1. Remove the radiator cap and check for coolant contamination.....2536
STEP 2. Check the radiator cap valve opening pressure.....2537
STEP 3. Check thermostat operation.....2537
STEP 4. Check the drive belt for slippage or damage.....2537
STEP 5. Retest the system.....2537
SPECIAL TOOL....2537
ON-VEHICLE SERVICE....2538
ENGINE COOLANT LEAK CHECK....2538
RADIATOR CAP VALVE OPENING PRESSURE CHECK....2538
ENGINE COOLANT REPLACEMENT....2539
ENGINE COOLANT CONCENTRATION CHECK....2540
WATER PUMP ENGINE COOLANT LEAK CHECK....2540
COOLING FAN CONTROL RELAY CONTINUITY CHECK....2541
COOLING FAN MOTOR CHECK....2542
THERMOSTAT....2543
REMOVAL SERVICE POINT....2543
INSTALLATION SERVICE POINTS....2544
INSPECTION....2545
THERMOSTAT CHECK....2545
WATER PUMP....2546
REMOVAL SERVICE POINT....2547
INSTALLATION SERVICE POINT....2547
WATER HOSE AND WATER PIPE....2548
INSTALLATION SERVICE POINTS....2548
RADIATOR....2549
<M/T>....2549
<CVT>....2550
REMOVAL SERVICE POINTS....2551
INSTALLATION SERVICE POINT....2551
GR00000900-15....2552
INTAKE AND EXHAUST....2552
SERVICE SPECIFICATIONS....2553
INTAKE AND EXHAUST DIAGNOSIS....2553
SYMPTOM PROCEDURES....2553
Inspection Procedure 1: Exhaust Leakage....2553
DIAGNOSIS....2553
STEP 1. Start the engine. Have an assistant stay in the driver’s seat. Raise the vehicle on a hoist. Have the assistant rev th....2553
STEP 2. Check the gasket or seal ring for cracks, damage.....2554
STEP 3. Check for loosening in each coupling section.....2554
STEP 4. Start the engine. Have an assistant stay in the driver’s seat. Raise the vehicle on a hoist. Have the assistant rev th....2554
Inspection Procedure 2: Abnormal Noise....2554
DIAGNOSIS....2554
STEP 1. Start the engine. Have an assistant stay in the driver' seat. Raise the vehicle on a hoist. Have the assistant rev the engine while searching for abnormal noise.....2554
STEP 2. Check for missing parts in the muffler. Tap the muffler lightly to check for loose baffles, etc.....2554
STEP 3. Check the hanger for cracks.....2554
STEP 4. Check for interference of the pipes and muffler with the body.....2555
STEP 5. Check the heat protectors.....2555
STEP 6. Check the pipes and muffler for damage.....2555
STEP 7. Start the engine. Have an assistant stay in the driver' seat. Raise the vehicle on a hoist. Have the assistant rev the engine while searching for abnormal noise.....2555
SPECIAL TOOL....2555
AIR CLEANER....2556
INSTALLATION SERVICE POINT....2557
INTAKE MANIFOLD....2557
INSTALLATION SERVICE POINTS....2558
INSPECTION....2558
EXHAUST MANIFOLD....2559
REMOVAL SERVICE POINT....2559
INSTALLATION SERVICE POINT....2560
INSPECTION....2560
EXHAUST PIPE AND MAIN MUFFLER....2561
REMOVAL SERVICE POINTS....2561
INSTALLATION SERVICE POINT....2562
GR00001000-16....2564
ENGINE ELECTRICAL....2564
CHARGING SYSTEM....2565
CHARGING SYSTEM DIAGNOSIS....2566
TROUBLESHOOTING HINTS....2566
TROUBLESHOOTING GUIDE....2566
STEP 1.....2566
STEP 2.....2566
STEP 3.....2567
STEP 4.....2567
STEP 5.....2567
STEP 6.....2567
STEP 7.....2567
STEP 8.....2567
STEP 9.....2567
STEP 10.....2568
ON-VEHICLE SERVICE....2570
GENERATOR OUTPUT LINE VOLTAGE DROP TEST....2570
OUTPUT CURRENT TEST....2572
REGULATED VOLTAGE TEST....2574
WAVEFORM CHECK USING AN OSCILLOSCOPE....2576
MEASUREMENT METHOD....2576
STANDARD WAVEFORM....2576
GENERATOR ASSEMBLY....2579
REMOVAL SERVICE POINTS....2579
INSTALLATION SERVICE POINT....2579
STARTING SYSTEM....2580
STARTING SYSTEM DIAGNOSIS....2581
TROUBLESHOOTING HINTS....2581
TROUBLESHOOTING GUIDE....2581
STEP 1.....2581
STEP 2.....2582
STEP 3.....2582
STEP 4.....2582
STEP 5.....2582
ON-VEHICLE SERVICE....2583
STARTER RELAY CONTINUITY CHECK....2583
STARTER MOTOR ASSEMBLY....2584
REMOVAL SERVICE POINT....2584
INSPECTION....2585
PINION GAP ADJUSTMENT....2585
MAGNETIC SWITCH PULL-IN TEST....2585
MAGNETIC SWITCH HOLD-IN TEST....2585
FREE RUNNING TEST....2586
MAGNETIC SWITCH RETURN TEST....2586
IGNITION SYSTEM....2586
ON-VEHICLE SERVICE....2590
IGNITION COIL CHECK....2590
SPARK PLUG CHECK AND CLEANING....2591
SPARK PLUG GAP CHECK....2591
SPARK PLUG INSULATION RESISTANCE CHECK....2591
SPARK PLUG CLEANING....2591
CAMSHAFT POSITION SENSOR CHECK....2592
CRANKSHAFT POSITION SENSOR CHECK....2592
KNOCK SENSOR CHECK....2592
IGNITION COIL....2592
CAMSHAFT POSITION SENSOR....2593
CRANKSHAFT POSITION SENSOR....2594
KNOCK SENSOR....2595
GR00001100-32....2596
POWER PLANT MOUNT....2596
SERVICE SPECIFICATION....2597
ENGINE MOUNTING....2597
TRANSAXLE MOUNTING....2598
<M/T>....2598
<CVT>....2599
ENGINE ROLL STOPPER ROD....2599
FRONT AXLE CROSSMEMBER....2600
REMOVAL SERVICE POINT....2602
INSTALLATION SERVICE POINTS....2602
GR00001600-31....2604
WHEEL AND TIRE....2604
GENERAL INFORMATION....2605
SPECIFICATIONS....2605
FLAT TIRE TEMPORARY REPAIR KIT....2605
TIRE PRESSURE MONITORING SYSTEM (TPMS)....2606
SERVICE SPECIFICATIONS....2608
SPECIAL TOOLS....2609
WHEEL AND TIRE DIAGNOSIS....2611
PURPOSE....2612
PROCEDURE <Balancing Tips>....2612
<Confirming Proper Balance>....2613
<Wheel Balancer Calibration Checks>....2613
TIRE PRESSURE MONITORING SYSTEM (TPMS) DIAGNOSIS....2615
TPMS MAY NOT WORK NORMALLY IN THE FOLLOWING CIRCUMSTANCES:....2615
WHEN THE TPMS WARNING LIGHT IS ON....2615
AFTER REPLACING TPMS COMPONENTS....2615
HOW TO CONNECT THE SCAN TOOL (M.U.T.-III)....2616
HOW TO READ AND ERASE DIAGNOSTIC TROUBLE CODES....2616
HOW TO READ DATA LIST....2617
TPMS WARNING LIGHT CHECK....2618
TPMS DIAGNOSTIC TROUBLE CODE PROCEDURES....2622
DTC C1564: Vehicle speed data invalid....2622
DIAGNOSIS....2622
STEP 1. Using scan tool MB991958, diagnose the CAN bus lines.....2622
STEP 2. DTC recheck after resetting CAN bus lines....2622
STEP 3. Use scan tool MB991958 to confirm a DTC of other systems.....2622
STEP 4. Check whether the DTC is set again.....2623
DTC C1900: Tire ID code No registration....2623
DIAGNOSIS....2623
STEP 1. Using scan tool MB991958, diagnose the CAN bus lines.....2623
STEP 2. Check whether the DTC is set again.....2624
STEP 3. Check whether the DTC is set again.....2624
STEP 4. Check whether the DTC is set again.....2624
DTC C1901: Vehicle speed signal....2625
DIAGNOSIS....2625
STEP 1. Using scan tool MB991958, diagnose the CAN bus lines.....2625
STEP 2. DTC recheck after resetting CAN bus lines....2625
STEP 3. Using scan tool other system DTC....2625
STEP 4. Check the TPMS transmitter acceleration.....2626
STEP 5. Check whether the DTC is set again.....2626
DTC C1902: Reset fail (warning threshold)....2626
DIAGNOSIS....2627
STEP 1. Using scan tool MB991958, diagnose the CAN bus lines.....2627
STEP 2. DTC recheck after resetting CAN bus lines.....2627
STEP 3. Check whether the DTC is set.....2627
STEP 4. Check the tire IDs for the TPMS transmitters.....2627
STEP 5. Check the tire IDs for the TPMS transmitters.....2628
STEP 6. Check the reset function.....2628
STEP 7. Check for TPMS transmitter.....2628
STEP 8. Check whether the DTC is set again.....2628
DTC C1910: Transmitter BATT voltage, Tire1 DTC C1920: Transmitter BATT voltage, Tire2 DTC C1930: Transmitter BATT voltage, Tire3.....2629
DIAGNOSIS....2629
STEP 1. Using scan tool MB991958, diagnose the CAN bus lines.....2629
STEP 2. DTC recheck after resetting CAN bus lines....2629
STEP 3. Check the tire IDs for the TPMS transmitters.....2630
STEP 4. Check for TPMS transmitter.....2630
STEP 5. Check whether the DTC is set again.....2630
DTC C1912: Tire air pressure low, Tire1 DTC C1922: Tire air pressure low, Tire2 DTC C1932: Tire air pressure low, Tire3 DTC C1942: Tire air pressure low, Tire4....2631
DIAGNOSIS....2631
STEP 1. Using scan tool MB991958, diagnose the CAN bus lines.....2631
STEP 2. DTC recheck after resetting CAN bus lines....2631
STEP 3. Tire check....2631
STEP 4. Check whether the DTC is set again.....2632
STEP 5. Check whether the DTC is set again.....2632
STEP 6. Tire pressure check by scan tool....2632
STEP 7. Check whether the DTC is set again.....2633
STEP 8. Check whether the DTC is set again.....2633
DTC C1913: Acceleration sensor, Tire1 DTC C1923: Acceleration sensor, Tire2 DTC C1933: Acceleration sensor, Tire3 DTC C1943: Acc.....2633
DIAGNOSIS....2634
STEP 1. Using scan tool MB991958, diagnose the CAN bus lines.....2634
STEP 2. DTC recheck after resetting CAN bus lines....2634
STEP 3. Check for TPMS transmitter.....2635
STEP 4. Check whether the DTC is set again.....2635
DTC C1915: Transmitter OFF mode, Tire1 DTC C1925: Transmitter OFF mode, Tire2 DTC C1935: Transmitter OFF mode, Tire3 DTC C1945: Transmitter OFF mode, Tire4....2635
DIAGNOSIS....2636
STEP 1. Using scan tool MB991958, diagnose the CAN bus lines.....2636
STEP 2. DTC recheck after resetting CAN bus lines....2636
STEP 3. Check whether the DTC is set again.....2636
STEP 4. Check whether the DTC is set again.....2636
TPMS SYMPTOM PROCEDURES....2637
Inspection Procedure 1: The TPMS warning light stays ON.....2637
DIAGNOSIS....2637
STEP 1. Inspect the all tires.....2637
STEP 2. After the tire inflation pressure is adjusted and the TPMS transmitter sends inflation pressure information on it, check the TPMS warning light.....2638
STEP 3. Check the tire inflation pressure again.....2638
STEP 4. Using scan tool MB991958, diagnose the CAN bus lines.....2638
STEP 5. Using scan tool MB991958, read the diagnostic trouble code.....2638
STEP 6. Check the TPMS warning light.....2639
STEP 7. Retest the system.....2639
Inspection Procedure 2: The TPMS warning light flash for about 1 minute and then remain illuminated.....2639
DIAGNOSIS....2639
STEP 1. Using scan tool MB991958, diagnose the CAN bus lines.....2639
STEP 2. Using scan tool MB991958, read the diagnostic trouble code.....2640
STEP 3. Check the combination meter.....2640
STEP 4. Retest the system.....2640
ON-VEHICLE SERVICE....2644
TIRE INFLATION PRESSURE CHECK....2644
TIRE WEAR CHECK....2644
WHEEL RUNOUT CHECK....2644
TPMS TRANSMITTER CHECK OR REPLACE....2645
TPMS SPECIAL FUNCTION....2645
TIRE PRESSURE SENSOR ID REGISTRATION....2645
'TIRE PRESSURE SENSOR ID REGISTRATION' METHOD....2646
'TIRE PRS. SENSOR ID REG. (Set2)' METHOD....2647
TIRE PRESSURE SENSOR ID CHECK....2647
'TIRE PRESSURE SENSOR ID CHECK' METHOD....2647
TPMS TRANSMITTER CHECK....2647
WHEEL AND TIRE....2648
INSTALLATION SERVICE POINT....2648
TIRE PRESSURE MONITORING SYSTEM (TPMS)....2649
TPMS RECEIVER....2649
TPMS TRANSMITTER....2650
REMOVAL SERVICE POINT....2652
INSTALLATION SERVICE POINTS....2654
GR00001700-35....2656
SERVICE BRAKES....2656
GR00001900-35C....2658
ACTIVE STABILITY CONTROL SYSTEM (ASC)....2658
SERVICE SPECIFICATIONS....2660
DIAGNOSIS....2660
ASC DIAGNOSTIC TROUBLE CODE DETECTION CONDITIONS....2660
ASC DIAGNOSTIC TROUBLESHOOTING STRATEGY....2660
PRECAUTIONS FOR DIAGNOSIS....2661
ASC INDICATOR LIGHT, ASC OFF INDICATOR LIGHT, ABS WARNING LIGHT AND BRAKE WARNING LIGHT CHECK....2662
DIAGNOSTIC FUNCTION....2662
ON-BOARD DIAGNOSTICS....2662
HOW TO CONNECT THE SCAN TOOL (M.U.T.-III)....2663
HOW TO READ AND ERASE DIAGNOSTIC TROUBLE CODES....2663
HOW TO READ DATA LIST....2664
HOW TO PERFORM ACTUATOR TEST....2664
HOW TO DIAGNOSE THE CAN BUS LINE....2665
CHECK OF FREEZE FRAME DATA....2666
FAIL-SAFE FUNCTIONS....2668
DIAGNOSTIC TROUBLE CODE PROCEDURES....2675
Code No. C1200 FR wheel speed sensor Code No. C1205 FL wheel speed sensor Code No. C1210 RR wheel speed sensor Code No. C1215 RL wheel speed sensor....2675
DIAGNOSIS....2675
STEP 1. Using scan tool MB991958, diagnose the CAN bus lines.....2675
STEP 2. Diagnostic trouble code recheck after resetting CAN bus lines....2676
STEP 3. Using scan tool MB991958, check data list....2676
STEP 4. Measure the voltage at the ASC-ECU connector.....2676
STEP 5. Measure the resistance at the ASC-ECU connector.....2677
STEP 6. Check the wiring harness wires between the ASC-ECU connector FR (+) or FR (-) terminal and the front wheel speed sensor (RH) connector terminal.....2677
STEP 7. Check the wiring harness wires between the ASC-ECU connector FL (+) or FL (-) terminal and the front wheel speed sensor (LH) connector terminal.....2677
STEP 8. Check the wiring harness wires between the ASC-ECU connector RR (+) or RR (-) terminal and the rear wheel speed sensor (RH) connector terminal.....2678
STEP 9. Check the wiring harness wires between ASC-ECU connector A-05 RL (+) or RL (-) terminal and the rear wheel speed sensor (LH) connector terminal.....2678
STEP 10. Measure the voltage at the ASC-ECU connector.....2678
STEP 11. Check the wiring harness wires between the ASC-ECU connector FR (+) or FR (-) terminal and the front wheel speed sensor (RH) connector terminal.....2679
STEP 12. Check the wiring harness wires between the ASC-ECU connector FL (+) or FL (-) terminal and the front wheel speed sensor (LH) connector terminal.....2679
...
SYMPTOM PROCEDURES....2842
Inspection Procedure 1: Scan tool MB991958 cannot communicate with electric power steering system <ECU power supply circuit system check>.....2842
STEP 3. Check the wiring harness wires between terminal No. 4 of each PTC heater relay connector (1, 2 and 3) and fusible link (7) for open or short circuit.....2893
STEP 4. Measure the resistance at the PTC heater relay connectors (1, 2 and 3).....2893
STEP 5. Check the wiring harness wires between each PTC heater relay connector (1, 2 and 3) and body ground for open or short circuit.....2894
STEP 6. Check the wiring harness wires between each PTC heater relay connector (1, 2 and 3) and the heater control unit (PTC-ECU) terminals 'E' and 'COME' for open or short circuit.....2894
STEP 7. Measure the voltage at the PTC heater relay connectors (1, 2 and 3).....2894
STEP 8. Check the wiring harness wires between each PTC heater relay connector (1, 2 and 3) and the PTC heater control unit (PTC-ECU) connector terminals 'HTR1', 'HTR2' and 'HTR3' for open or short circuit.....2894
STEP 9. Measure the resistance at the PTC heater relay connectors (1, 2 and 3).....2895
STEP 10. Check the wiring harness wires between each PTC heater relay connector (1, 2 and 3) and body ground for open or short circuit.....2895
SPECIAL TOOLS....2896
ON-VEHICLE SERVICE....2896
SIMPLE INSPECTION OF THE A/C PRESSURE SENSOR....2896
DRIVE BELT INSPECTION....2897
PERFORMANCE TEST....2898
TEST CONDITION SETTING....2898
COOLING PERFORMANCE CHECK....2898
REFRIGERANT GAS PRESSURE CHECK....2899
RELAY CHECK....2900
BLOWER RELAY CONTINUITY CHECK....2900
A/C COMPRESSOR RELAY CONTINUITY CHECK....2901
PTC HEATER RELAY 1, 2 and 3 CONTINUITY CHECK....2902
IDLE-UP INSPECTION....2902
REPLACE THE AIR REFRESHER....2906
HEATER CONTROL UNIT....2908
INSTALLATION SERVICE POINTS....2909
INSPECTION....2911
BLOWER SWITCH CONTINUITY CHECK....2911
AIR CONDITIONING SWITCH CONTINUITY CHECK....2912
DEF DETECTION SWITCH CONTINUITY CHECK....2912
HEATER UNIT AND BLOWER ASSEMBLY....2914
REMOVAL SERVICE POINTS....2915
INSTALLATION SERVICE POINT....2916
REASSEMBLY SERVICE POINTS....2917
FIN THERMO SENSOR CHECK....2918
PTC HEATER CONTINUITY CHECK....2918
HEATER HOSE....2919
PTC HEATER CONTROL UNIT....2920
BLOWER ASSEMBLY AND RESISTOR....2921
RESISTOR CHECK....2921
BLOWER FAN AND MOTOR CHECK....2922
COMPRESSOR ASSEMBLY....2923
REMOVAL SERVICE POINTS....2924
INSTALLATION SERVICE POINT....2924
INSPECTION....2925
CHECK THE MAGNETIC CLUTCH FOR A/C COMPRESSOR....2925
DISASSEMBLY SERVICE POINTS....2926
REASSEMBLY SERVICE POINTS....2926
CONDENSER ASSEMBLY....2927
REMOVAL SERVICE POINT....2928
REFRIGERANT LINE....2928
REMOVAL SERVICE POINT....2929
DUCTS....2930
VENTILATORS....2932
GR00002600-55B....2934
AUTOMATIC AIR CONDITIONING....2934
GENERAL DESCRIPTION....2935
SAFETY PRECAUTIONS....2935
OPERATION....2935
AUTOMATIC A/C DIAGNOSIS....2936
DIAGNOSTIC FUNCTION....2937
HOW TO CONNECT THE SCAN TOOL (M.U.T.-III)....2937
HOW TO READ AND ERASE DIAGNOSTIC TROUBLE CODES....2938
HOW TO READ DATA LIST....2938
HOW TO PERFORM ACTUATOR TEST....2939
HOW TO DIAGNOSE THE CAN BUS LINE....2940
CHECK OF FREEZE FRAME DATA....2941
<Engine control module>....2942
DIAGNOSTIC TROUBLE CODE PROCEDURES....2942
Code No.B1001: Inside temperature sensor low Code No.B1002: Inside temperature sensor high....2942
Code No.B1041: A/M damper potentiometer high Code No.B1042: A/M damper potentiometer low....2942
DIAGNOSIS....2943
STEP 1. Using scan tool MB991958, check data list.....2943
STEP 2. Check open and short circuit in SENB, A/MP and SENG line between air mixing damper control motor and potentiometer connector (potentiometer side) and auto A/C controller assembly (A/C-ECU) connector.....2943
STEP 3. Check the air mixing damper control motor and potentiometer.....2943
STEP 4. Check whether the diagnostic trouble code is stored again.....2943
Code No.B1045: Air mix damper motor....2943
DIAGNOSIS....2944
STEP 1. Using scan tool MB991958, check actuator test of A/C controller assembly (A/C-ECU) check.....2944
STEP 2. Check open and short circuit in COOL and HOT line between air mixing damper control motor and potentiometer connector (damper control motor side) and auto A/C controller assembly (A/C-ECU) connector.....2944
STEP 3. Check the air mixing damper control motor and potentiometer.....2944
STEP 4. Check whether the diagnostic trouble code is stored again.....2944
Code No.B1061: Air outlet damper potentio.high Code No.B1062: Air outlet damper potentio.low....2944
DIAGNOSIS....2945
STEP 1. Using scan tool MB991958, check data list.....2945
STEP 2. Check open and short circuit in SENB, MODP and SENG line between mode selection damper control motor and potentiometer connector (potentiometer side) and auto A/C controller assembly (A/C-ECU) connector.....2945
STEP 3. Check the mode selection damper control motor and potentiometer.....2945
STEP 4. Check whether the diagnostic trouble code is stored again.....2945
Code No.B1065: Air outlet changeover DMPR.motor....2945
DIAGNOSIS....2946
STEP 1. Using scan tool MB991958, check actuator test of A/C controller assembly (A/C-ECU) check.....2946
STEP 2. Check open and short circuit in DEF and FACE line between mode selection damper control motor and potentiometer connector (mode selection damper control motor side) and auto A/C controller assembly (A/C-ECU) connector....2946
STEP 3. Check the mode selection damper control motor and potentiometer.....2946
STEP 4. Check whether the diagnostic trouble code is stored again.....2946
Code No. B1083 EEPROM error....2946
Code No. U1000: OSS/F.A.S.T._OSS CAN timeout....2947
DIAGNOSIS....2948
STEP 1. Using SCAN tool MB991958, diagnose the CAN bus lines.....2948
STEP 2. Check whether the DTC is set.....2948
STEP 3. Check whether the DTC is set again.....2948
STEP 4. Check whether the diagnostic trouble code is set again.....2948
STEP 5. Check whether the diagnostic trouble code is set again.....2949
STEP 6. Check whether the diagnostic trouble code is set again.....2949
Code No.U1100 Engine CAN timeout....2949
DIAGNOSIS....2950
STEP 1. Using SCAN tool MB991958, diagnose the CAN bus lines.....2950
STEP 2. Check whether the DTC is set.....2950
STEP 3. Check whether the DTC is set again.....2951
STEP 4. Check whether the diagnostic trouble code is set again.....2951
STEP 5. Check whether the diagnostic trouble code is set again.....2951
STEP 6. Check whether the diagnostic trouble code is set again.....2951
Code No.U1108 Meter CAN timeout/Not equipped....2952
DIAGNOSIS....2953
STEP 1. Using scan tool MB991958, diagnose the CAN bus lines.....2953
STEP 2. Check whether the DTC is set.....2953
STEP 3. Check whether the DTC is set again.....2953
STEP 4. Check whether the diagnostic trouble code is set again.....2953
STEP 5. Check whether the diagnostic trouble code is set again.....2954
STEP 6. Check whether the diagnostic trouble code is set again.....2954
Code No. U1109: ETACS-ECU CAN time-out/Not equipped....2954
DIAGNOSIS....2955
STEP 1. Using SCAN tool MB991958, diagnose the CAN bus lines.....2955
STEP 2. Check whether the DTC is set.....2956
STEP 3. Check whether the DTC is set again.....2956
STEP 4. Check whether the diagnostic trouble code is set again.....2956
STEP 5. Check whether the diagnostic trouble code is set again.....2956
STEP 6. Check whether the diagnostic trouble code is set again.....2957
Code No.U1190 No receive fault detect signal....2957
Code No.U1195 Coding not completed....2957
SYMPTOM PROCEDURES....2958
INSPECTION PROCEDURE 1: Communication with the scan tool MB991958 is not possible.....2958
INSPECTION PROCEDURE 2: Cool air does not come....2958
DIAGNOSIS....2958
STEP 1. Check the blower operation....2958
STEP 2. Check the A/C compressor operation....2959
STEP 3. Using scan tool MB991958, diagnose the CAN bus lines.....2959
STEP 4. Using scan tool MB991958, DTC check.....2959
STEP 5. Check the refrigerant level.....2959
INSPECTION PROCEDURE 3: The blower does not work....2959
DIAGNOSIS....2960
STEP 1. Using scan tool MB991958, diagnose the CAN bus lines.....2960
STEP 2. Using scan tool MB991958, DTC check.....2960
STEP 3. Check the blower relay.....2960
STEP 4. Check open circuit in blower relay line between IG2 relay, fusible link (2), and blower relay and body ground.....2960
STEP 5. Check the blower motor.....2960
STEP 6. Voltage measurement at blower motor connector.....2960
STEP 7. Check open circuit in blower motor line between blower relay, blower motor and power transistor.....2961
STEP 8. Resistance measurement at the power transistor connector.....2961
STEP 9. Check open circuit in RVM, BASE and E line between power transistor, body ground and auto A/C controller assembly (A/C-ECU).....2961
STEP 10. Check the data list below on the scan tool MB991958.....2961
STEP 11. Replace the power transistor and recheck the trouble symptom....2961
INSPECTION PROCEDURE 4: The blower air volume cannot be changed....2961
DIAGNOSIS....2962
STEP 1. Using SCAN tool MB991958, diagnose the CAN bus lines.....2962
STEP 2. Using scan tool MB991958, DTC check.....2962
STEP 3. Resistance measurement at the power transistor connector.....2962
STEP 4. Check open circuit in RVM, BASE and E line between power transistor, body ground and auto A/C controller assembly (A/C-ECU)....2962
STEP 5. Check the data list below on the scan tool MB991958.....2962
STEP 6. Replace the power transistor and check the trouble symptom....2963
INSPECTION PROCEDURE 5: The Inside/Outside Air Changeover is impossible.....2963
DIAGNOSIS....2963
STEP 1. Using scan tool MB991958, DTC check.....2963
STEP 2. Using scan tool MB991958, check actuator test of A/C controller assembly (A/C-ECU) check.....2963
STEP 3. Check open and short circuit in FRE and REC line between IG2 relay, outside/inside air selection damper control motor and auto A/C controller assembly (A/C-ECU).....2963
STEP 4. Check the data list below on the scan tool MB991958.....2964
STEP 5. Replace the air outside/inside air circulation switching damper motor, and then recheck the trouble symptom.....2964
INSPECTION PROCEDURE 6: A/C pressure sensor system....2964
DIAGNOSIS....2964
STEP 1. Inspection of the A/C pressure sensor....2964
STEP 2. Check open circuit in AC/P, BVSE&ACPE and BVS5 & ACP5 line between A/C pressure sensor connector and engine control module connector.....2964
STEP 3. Check the data list below on the scan tool MB991958.....2965
STEP 4. Retest the system.....2965
INSPECTION PROCEDURE 7: The A/C compressor does not work....2965
DIAGNOSIS....2965
STEP 1. Using scan tool MB991958, diagnose the CAN bus lines.....2965
STEP 2. Using scan tool MB991958, DTC check.....2965
STEP 3. Voltage measurement at A/C compressor assembly connector.....2966
STEP 4. Check the A/C compressor.....2966
STEP 5. Check the refrigerant level.....2966
STEP 6. Replace the engine control module, and then recheck the trouble symptom....2966
STEP 7. Check the A/C compressor relay....2966
STEP 8. Voltage measurement at A/C compressor relay connector.....2966
STEP 9. Check open circuit in A/C compressor relay line between fusible link (6) and A/C compressor relay.....2967
STEP 10. Check open circuit in A/C compressor and clutch assembly line between A/C compressor relay and A/C compressor and clutch.....2967
STEP 11. Check open circuit in engine control module (AC/R) line between IG2 relay, A/C compressor relay and engine control module....2967
INSPECTION PROCEDURE 8: A/C-ECU power supply system....2967
DIAGNOSIS....2967
STEP 1. Check whether the DTC is set.....2967
STEP 2. Measure the voltage at the auto A/C controller assembly (A/C-ECU) connector.....2968
STEP 3. Check open circuit in IG2 line between IG (2) relay and A/C controller assembly (A/C-ECU) connector.....2968
STEP 4. Measure the resistance at the auto A/C controller assembly (A/C-ECU) connector.....2968
STEP 5. Check open circuit in E line between auto A/C controller assembly (A/C-ECU) connector and body ground.....2968
SPECIAL TOOLS....2972
HEATER CONTROL UNIT....2975
DAMPER CONTROL MOTOR ASSEMBLY....2976
REMOVAL SERVICE POINT....2977
CHECK THE MODE SELECTION DAMPER CONTROL MOTOR AND POTENTIOMETER....2977
CHECK THE AIR MIXING DAMPER CONTROL MOTOR AND POTENTIOMETER....2978
CHECK THE OUTSIDE/INSIDE AIR SELECTION DAMPER CONTROL MOTOR....2978
AMBIENT TEMPERATURE SENSOR....2979
AMBIENT TEMPERATURE SENSOR CHECK....2979
OTHER PARTS....2980
GR00002700-42B....2982
KEYLESS OPERATION SYSTEM (KOS)....2982
SPECIAL TOOLS....2984
DIAGNOSIS....2986
CHECK OF FREEZE FRAME DATA....2986
HOW TO CONNECT THE SCAN TOOL (M.U.T.-III)....2987
HOW TO READ AND ERASE DIAGNOSTIC TROUBLE CODES....2988
HOW TO DIAGNOSE THE CAN BUS LINES....2988
FORCED POWER SUPPLY OUTPUT PROCEDURE....2989
WARNING AND WARNING INDICATOR LIST FOR KOS....2991
WARNING AND WARNING INDICATOR LIST FOR OSS....2993
DIAGNOSTIC TROUBLE CODE PROCEDURES....2996
DTC B1130: Ignition power supply....2996
DIAGNOSIS....2997
STEP 1. Using scan tool MB991958, diagnose the CAN bus line.....2997
STEP 2. Using scan tool MB991958, read the diagnostic trouble code.....2997
STEP 3. Using scan tool MB991958, check data list.....2998
STEP 4. ACC relay check.....2999
STEP 5. Resistance measurement at ACC relay connector (ground line).....2999
STEP 6. Check of open circuit in ground line between the ACC relay connector and the body ground.....2999
STEP 7. Voltage measurement at ACC relay connector (ACC line and power supply line).....2999
STEP 8. Check of short and open circuit in ACC line between the KOS&OSS-ECU connector and the ACC relay connector.....3000
STEP 9. Check of short and open circuit in power supply line between the junction block connector and the ACC relay connector.....3000
STEP 10. Voltage measurement at ETACS-ECU connector (ACC line).....3000
STEP 11. IG1 relay check.....3000
STEP 12. Resistance measurement at IG1 relay connector (ground line).....3001
STEP 13. Check of open circuit in ground line between the IG1 relay connector and the body ground.....3001
STEP 14. Voltage measurement at IG1 relay connector (IG1 line and power supply line).....3001
STEP 15. Check of short and open circuit in IG1 line between the KOS&OSS-ECU connector and the IG1 relay connector.....3001
STEP 16. Check of short and open circuit in power supply line between the junction block connector and the IG1 relay connector.....3002
STEP 17. Voltage measurement at ETACS-ECU connector (IG1 line).....3002
STEP 18. IG2 relay check.....3002
STEP 19. Resistance measurement at IG2 relay connector (ground line).....3002
STEP 20. Check of open circuit in ground line between the IG2 relay connector and the body ground.....3003
STEP 21. Voltage measurement at IG2 relay connector (IG2 line).....3003
STEP 22. Check of short and open circuit in IG2 line between the KOS&OSS-ECU connector and the IG2 relay connector.....3003
STEP 23. Check of short and open circuit in power supply line between the junction block connector and the IG2 relay connector.....3003
STEP 24. Voltage measurement at ETACS-ECU connector (IG2 line).....3004
STEP 25. Using scan tool MB991958, check data list.....3005
STEP 26. Recheck for diagnostic trouble code.....3006
STEP 27. Recheck for diagnostic trouble code.....3006
DTC B1131: Starter setting circuit fail....3006
DIAGNOSIS....3007
STEP 1. Check of short or open circuit in ST line between KOS&OSS-ECU connector and engine control module connector.....3007
STEP 2. Voltage measurement at engine control module connector (STO terminal).....3007
STEP 3. Recheck for diagnostic trouble code.....3007
DTC B1132: Starter circuit fail....3008
DIAGNOSIS....3008
STEP 1. Check of short or open circuit in ST line between KOS&OSS-ECU connector and engine control module connector.....3008
STEP 2. Using scan tool MB991958, check other system data list.....3008
STEP 3. Recheck for diagnostic trouble code.....3009
STEP 4 Recheck for diagnostic trouble code.....3009
STEP 5 Recheck for diagnostic trouble code.....3009
DTC B1133: IG1 setting circuit fail....3010
DIAGNOSIS....3010
STEP 1. Check of short circuit in IG1 line between KOS&OSS-ECU connector and IG1 relay connector.....3010
STEP 2. IG1 relay check.....3010
STEP 3. Voltage measurement at IG1 relay connector (IG1 terminal).....3010
STEP 4. Using scan tool MB991958, check data list.....3011
STEP 5. Recheck for diagnostic trouble code.....3011
DTC B1134: ECU power supply....3012
DIAGNOSIS....3012
STEP 1. Check the battery power supply circuit to the ETACS-ECU.....3012
STEP 2. Using scan tool MB991958, check data list.....3013
STEP 3. Check of open circuit in IOD line between KOS&OSS-ECU connector and fusible link.....3013
STEP 4. Check of open circuit in +B line between KOS&OSS-ECU connector and fusible link.....3013
STEP 5. Recheck for diagnostic trouble code.....3014
DTC B1135: Engine switch....3014
DIAGNOSIS....3014
STEP 1. Engine switch check.....3014
STEP 2. Using scan tool MB991958, check data list.....3015
STEP 3. Check of short to power supply, short to ground, and open circuit in SW1 line between KOS&OSS-ECU connector and engine switch connector.....3015
STEP 4. Check of short to ground or open circuit between relay box (fuse) connector and engine switch connector.....3015
STEP 5. Check of open circuit between engine switch connector and body ground.....3015
STEP 6. Check of short and open circuit in SW2 line between KOS&OSS-ECU connector and engine switch connector.....3016
STEP 7. Recheck for diagnostic trouble code.....3016
DTC B1136: Stop light switch....3016
DIAGNOSIS....3017
STEP 1. Using scan tool MB991958, diagnose the CAN bus line.....3017
STEP 2. Check of short to ground and open circuit in STP1 line between stop light switch connector and KOS&OSS-ECU connector....3017
STEP 3. Check of short to ground and open circuit in BKLP line between stop light switch connector and ETACS-ECU connector....3017
STEP 4. Using scan tool MB991958, check other system data list.....3018
STEP 5. Using scan tool MB991958, check data list.....3018
STEP 6. Recheck for diagnostic trouble code.....3019
DTC B1137: P range detect SW....3019
DIAGNOSIS....3020
STEP 1. Check of selector lever assembly (P range detection switch)....3020
STEP 2. Using scan tool MB991958, read other system diagnostic trouble code....3020
STEP 3. Check of short to power supply and open circuit in PDSW line between selector lever assembly connector and KOS&OSS-ECU connector....3021
STEP 4. Using scan tool MB991958, check data list.....3021
STEP 5. Recheck for diagnostic trouble code.....3022
DTC B1157: EEPROM fail DTC B1158: ECU internal error....3022
DIAGNOSIS....3022
Recheck for diagnostic trouble code.....3022
DTC B1160: Key code not programmed DTC U1199: VIN not programmed....3023
DTC B1161: VIN mismatch....3023
DTC B1163: Coding data mismatch....3023
DTC B1166: Special mode....3024
DTC B1731: PCM authentification timeout....3024
DTC B1A08: F.A.S.T. key1 fail DTC B1A09: F.A.S.T. key2 fail DTC B1A0A: F.A.S.T. key3 fail DTC B1A0B: F.A.S.T. key4 fail....3025
DIAGNOSIS....3025
STEP 1. Operate the keyless operation key, and recheck the diagnostic trouble code.....3025
STEP 2. Check whether the diagnostic trouble code is set again.....3025
DTC B1A10: F.A.S.T. key 1 low battery DTC B1A11: F.A.S.T. key 2 low battery DTC B1A12: F.A.S.T. key 3 low battery DTC B1A13: F.A.S.T. key 4 low battery....3026
DIAGNOSIS....3026
STEP 1. Replace the battery in the keyless operation key and recheck the diagnostic trouble code.....3026
STEP 2. Check whether the diagnostic trouble code is set again.....3027
DTC B1A24: Transponder ID not registered....3027
DIAGNOSIS....3027
STEP 1. Register the key ID.....3027
STEP 2. Recheck for diagnostic trouble code.....3027
DTC B1A25: Transponder ID unmatched....3028
DIAGNOSIS....3028
STEP 1. All of the registered keyless operation key and spare key should allow the engine switch to be turned all positions.....3028
STEP 2. Register the keyless operation key and spare key which cannot activate the engine switch again.....3029
STEP 3. It should allow the engine switch to be turned all positions, after register all of the keyless operation key and spare key again.....3029
STEP 4. Replace the keyless operation key and spare key which cannot activate the engine switch with a new one.....3030
STEP 5. It should allow the engine switch to be turned all positions, after replace the KOS&OSS-ECU, and then register all of the keyless operation key and spare key again.....3031
STEP 6. Recheck for diagnostic trouble code.....3031
DTC B1A28: PCM authentification error....3032
DTC B2352: Antenna fail....3032
DIAGNOSIS....3032
STEP 1. Key slot check.....3032
STEP 2. Check of short to power supply, short to ground, and open circuit in ANTP, ANTG line between the key slot connector and the KOS&OSS-ECU connector.....3033
STEP 3. Recheck for diagnostic trouble code.....3033
DTC B2400: F.A.S.T. key registration fail....3033
DIAGNOSIS....3034
STEP 1. Interference check at keyless operation key registration.....3034
STEP 2. Check of keyless operation key registration method.....3034
STEP 3. Using scan tool MB991958, diagnose the CAN bus line.....3034
STEP 4. Using scan tool MB991958, read the diagnostic trouble code.....3035
STEP 5. Replace the keyless operation key and recheck the diagnostic trouble code.....3035
DTC B2401: F.A.S.T. key ID not registered....3035
DIAGNOSIS....3035
STEP 1. Register the key ID.....3035
STEP 2. Check whether the diagnostic trouble code is set again.....3036
DTC B240A: DR side antenna (outdoor) open....3036
DIAGNOSIS....3036
STEP 1. Check of short to power supply, short to ground, and open circuit in EDRP, EDRG line between the outside transmission antenna assembly (driver' side) connector and the KOS&OSS-ECU connector.....3036
STEP 2. Keyless operation system communication test.....3036
STEP 3. Check whether the diagnosis trouble code is set again.....3037
DTC B240B: PS side antenna (outdoor) open....3037
DIAGNOSIS....3037
STEP 1. Check of short to power supply, short to ground, and open circuit in EASP, EASG line between the outside transmission antenna assembly (passenger' side) connector and the KOS&OSS-ECU connector.....3037
STEP 2. Keyless operation system communication test.....3037
STEP 3. Check whether the diagnosis trouble code is set again.....3038
DTC B240C: Tail gate antenna (outdoor) open....3038
DIAGNOSIS....3038
STEP 1. Check of short to power supply, short to ground, and open circuit in EGTP, EGTG line between the outside transmission antenna assembly (liftgate) connector and the KOS&OSS-ECU connector.....3038
STEP 2. Keyless operation system communication test.....3038
STEP 3. Check whether the diagnostic trouble code is set again.....3039
DTC B240D: Front antenna (indoor) open....3039
DIAGNOSIS....3039
STEP 1. Check of short to power supply, short to ground, and open circuit in INFP, INFG line between the inside transmission antenna assembly (front) connector and the KOS&OSS-ECU connector.....3039
STEP 2. Keyless operation system communication test.....3039
STEP 3. Check whether the diagnosis trouble code is set again.....3040
DTC B240E: RR antenna (indoor) open....3040
DIAGNOSIS....3040
STEP 1. Check of short to power supply, short to ground, and open circuit in INRP, INRG line between the inside transmission antenna assembly (rear) connector and the KOS&OSS-ECU connector.....3040
STEP 2. Keyless operation system communication test.....3040
STEP 3. Check whether the diagnostic trouble code is set again.....3041
DTC U0100: Engine CAN timeout....3041
DIAGNOSIS....3041
STEP 1. Using scan tool MB991958, diagnose the CAN bus line.....3041
STEP 2. Using scan tool MB991958, read the other system diagnostic trouble code.....3042
STEP 3. Using scan tool MB991958, read the other system diagnostic trouble code.....3042
STEP 4. Recheck for diagnostic trouble code.....3043
STEP 5. Recheck for diagnostic trouble code.....3043
DTC U0101: T/M CAN timeout....3043
DIAGNOSIS....3044
STEP 1. Using scan tool MB991958, diagnose the CAN bus line.....3044
STEP 2. Using scan tool MB991958, read the other system diagnostic trouble code.....3044
STEP 3. Using scan tool MB991958, read the other system diagnostic trouble code.....3045
STEP 4. Recheck for diagnostic trouble code.....3045
STEP 5. Recheck for diagnostic trouble code.....3045
DTC U0141: ETACS CAN timeout....3046
DIAGNOSIS....3046
STEP 1. Using scan tool MB991958, diagnose the CAN bus line.....3046
STEP 2. Using scan tool MB991958, read the other system diagnostic trouble code.....3046
STEP 3. Using scan tool MB991958, read the other system diagnostic trouble code.....3047
STEP 4. Recheck for diagnostic trouble code.....3047
STEP 5. Recheck for diagnostic trouble code.....3047
DTC U0155: Meter CAN timeout....3048
DIAGNOSIS....3048
STEP 1. Using scan tool MB991958, diagnose the CAN bus line.....3048
STEP 2. Using scan tool MB991958, read the combination meter diagnostic trouble code.....3048
STEP 3. Using scan tool MB991958, read the other system diagnostic trouble code.....3049
STEP 4. Recheck for diagnostic trouble code.....3049
STEP 5. Recheck for diagnostic trouble code.....3050
DTC U0164: A/C-ECU CAN timeout....3050
DIAGNOSIS....3050
STEP 1. Using scan tool MB991958, diagnose the CAN bus line.....3050
STEP 2. Using scan tool MB991958, read the other system diagnostic trouble code.....3051
STEP 3. Using scan tool MB991958, read the other system diagnostic trouble code.....3051
STEP 4. Recheck for diagnostic trouble code.....3052
STEP 5. Recheck for diagnostic trouble code.....3052
DTC U1190: No receive fault detect signal....3052
DIAGNOSIS....3053
STEP 1. Using scan tool MB991958, diagnose the CAN bus line.....3053
STEP 2. Using scan tool MB991958, read the other system diagnostic trouble code.....3053
STEP 3. Using scan tool MB991958, read the other system diagnostic trouble code.....3054
STEP 4. Recheck for diagnostic trouble code.....3054
DTC U1195: Coding not completed....3054
DIAGNOSIS....3055
STEP 1. Using scan tool MB991958, diagnose the CAN bus line.....3055
STEP 2. Using scan tool MB991958, read the other system diagnostic trouble code.....3055
STEP 3. Recheck for diagnostic trouble code.....3056
SYMPTOM PROCEDURES....3059
Inspection Procedure 1: Cannot communicate with KOS&OSS-ECU using the scan tool....3059
Inspection Procedure 2: The keyless operation key cannot be registered using the scan tool....3059
DIAGNOSIS....3060
STEP 1. Sufficiently insert the keyless operation key or spare key into the key slot, and then check the trouble symptom.....3060
STEP 2. Interference check of keyless operation key or spare key when it is inserted in the key slot.....3060
STEP 3. Retest the system.....3060
STEP 4. Using scan tool MB991958, read the diagnostic trouble code.....3060
STEP 5. Check which keyless operation key or spare key cannot be registered.....3061
STEP 6. Retest the system....3061
STEP 7. Retest the system....3061
STEP 8. Check for diagnostic trouble code.....3061
Inspection Procedure 3: Abnormality in KOS&OSS-ECU power supply and ground circuits....3061
DIAGNOSIS....3062
STEP 1. Resistance measurement at KOS&OSS-ECU connector (PGND, SGND terminal)....3062
STEP 2. Check of open circuit in PGND, SGND line between KOS&OSS-ECU connector and body ground....3062
STEP 3. Voltage measurement at KOS&OSS-ECU connector (+B, IOD terminal)....3062
STEP 4. Check of short to power supply, short to ground, and open circuit in +B, IOD line between fusible link and KOS&OSS-ECU connector....3062
Inspection Procedure 4: Keyless operation warning display does not disappear....3063
DIAGNOSIS....3063
STEP 1. Using scan tool MB991958, diagnose the CAN bus line.....3063
STEP 2. Using scan tool MB991958, read the other system diagnostic trouble code.....3063
STEP 3. Using scan tool MB991958, read the diagnostic trouble code.....3064
STEP 4. Retest the system.....3064
Inspection Procedure 5: No door will be locked or unlocked by operating a lock/unlock switch on any door....3064
DIAGNOSIS....3065
STEP 1. Using scan tool MB991958, diagnose the CAN bus line.....3065
STEP 2. Using scan tool MB991958, read the diagnostic trouble code.....3065
STEP 3. Using scan tool MB991958, read the other system diagnostic trouble code.....3066
STEP 4. Check the central door locking system operation.....3066
STEP 5. Check the customization function.....3066
STEP 6. Keyless operation system communication test.....3066
STEP 7. Check with another registered keyless operation key.....3067
STEP 8. Connection check of commercial electric products.....3067
STEP 9. Check of the troubles.....3067
STEP 10. Keyless operation key battery charged level check.....3067
STEP 11. Keyless operation key check.....3067
STEP 12. Check of the trouble.....3068
Inspection Procedure 6: Driver' door lock/unlock switch does not work....3068
DIAGNOSIS....3068
STEP 1. Using scan tool MB991958, read the diagnostic trouble code.....3068
STEP 2. Check the lock/unlock switch (driver’s side).....3068
STEP 3. Resistance measurement at lock/unlock switch (driver’s side) connector (ground line)....3069
STEP 4. Check of open circuit in ground line between the lock/unlock switch (driver’s side) connector and the body ground.....3069
STEP 5. Check of short to power supply, short to ground, and open circuit in DRRQ line between the KOS&OSS-ECU connector and t....3069
STEP 6. KOS communication test....3069
STEP 7. Connection check of commercial electric products....3069
STEP 8. Check of the troubles....3070
Inspection Procedure 7: Liftgate lock/unlock switch does not work....3070
DIAGNOSIS....3070
STEP 1. Using scan tool MB991958, read the diagnostic trouble code.....3070
STEP 2. Check the lock/unlock switch (liftgate).....3070
STEP 3. Resistance measurement at lock/unlock switch (liftgate) connector (ground line)....3071
STEP 4. Check of open circuit in ground line between the lock/unlock switch (liftgate) connector and the body ground.....3071
STEP 5. Check of short to power supply, short to ground, and open circuit in GTRQ line between the KOS&OSS-ECU connector and the lock/unlock switch (liftgate) connector.....3071
STEP 6. KOS communication test....3071
STEP 7. Connection check of commercial electric products....3071
STEP 8. Check of the troubles....3072
Inspection Procedure 8: Keyless entry function does not work....3072
DIAGNOSIS....3072
STEP 1. ETACS-ECU coding data check....3072
STEP 2. Using scan tool MB991958, diagnose the CAN bus line.....3073
STEP 3. Using scan tool MB991958, read the diagnostic trouble code.....3073
STEP 4. Check the power supply system....3073
STEP 5. Check the operation of the central door locking system.....3073
STEP 6. Using scan tool MB991958, check data list.....3074
STEP 7. Check with another registered keyless operation key.....3075
STEP 8. Check of the troubles....3075
Inspection Procedure 9: KOS timer lock function does not work....3075
DIAGNOSIS....3075
STEP 1. Check the keyless entry function operation....3075
STEP 2. Check the door entry function operation....3076
STEP 3. Using scan tool MB991958, read the other system diagnostic trouble code.....3076
STEP 4. Check of the troubles....3076
Inspection Procedure 10: Keyless entry hazard answer back function or the dome light answer back function does not work normally.....3076
DIAGNOSIS....3077
STEP 1. Check the hazard warning light....3077
STEP 2. Check the dome lights operation....3077
STEP 3. Check the keyless entry function operation....3077
STEP 4. Check the customization....3077
STEP 5. Using scan tool MB991958, read the diagnostic trouble code.....3078
STEP 6. Using scan tool MB991958, read the diagnostic trouble code.....3078
STEP 7. Check of the troubles....3078
Inspection Procedure 11: Outer buzzer does not sound.....3079
DIAGNOSIS....3079
STEP 1. Using scan tool MB991958, read the diagnostic trouble code.....3079
STEP 2. Using scan tool MB991958, read the other system diagnostic trouble code.....3079
STEP 3. Check the customization.....3080
STEP 4. Using scan tool MB991958, read the actuator test.....3080
STEP 5. Resistance measurement at outer buzzer connector (ground terminal).....3080
STEP 6. Check of open circuit in ground line between the outer buzzer connector and the body ground.....3080
STEP 7. Check of short to power supply, short to ground, and open circuit in DRVB line between the outer buzzer connector and the KOS&OSS-ECU connector.....3081
STEP 8. Check of the troubles.....3081
Inspection Procedure 12: Power door locks with selective unlocking does not work.....3081
DIAGNOSIS....3081
STEP 1. Check the customization.....3081
STEP 2. Power door locks with selective unlocking operation check.....3082
STEP 3. Keyless entry function operation check.....3082
STEP 4. Door entry function operation check.....3082
STEP 5. Check of the troubles.....3082
Inspection Procedure 13: Vehicle power does not turn 'ON'. (not possible with both of power supply mode 'ACC' and 'ON')....3083
DIAGNOSIS....3083
STEP 1. Battery check.....3083
STEP 2. Using scan tool MB991958, diagnose the CAN bus line.....3083
STEP 3. Using scan tool MB991958, communicates with this system.....3084
STEP 4. Using scan tool MB991958, read the diagnostic trouble code.....3084
STEP 5. Engine switch check.....3084
STEP 6. Keyless operation key battery charged level check <Except spare key>.....3085
STEP 7. Customized contents check.....3085
STEP 8. Check of the troubles.....3085
STEP 9. Keyless operation system communication test.....3085
STEP 10. Check with another registered keyless operation key.....3085
STEP 11. Connection check of commercial electric products.....3086
STEP 12. Keyless operation key check.....3086
STEP 13. Check of the troubles.....3086
STEP 14. Check of the troubles.....3086
STEP 15. Check of the troubles.....3086
STEP 16. Using scan tool MB991958, read the diagnostic trouble code.....3087
Inspection Procedure 14: Engine does not start (cranking is not performed).....3087
DIAGNOSIS....3087
STEP 1. Battery check.....3087
STEP 2. Using scan tool MB991958, communicates with this system.....3088
STEP 3. Using scan tool MB991958, read the diagnostic trouble code.....3088
STEP 4. Using scan tool MB991958, check data list.....3089
STEP 5. Stop Light Switch Check....3089
STEP 6. Using scan tool MB991958, other system data list.....3090
STEP 7. Check of short to power supply, short to ground, and open circuit in ST line between KOS&OSS-ECU connector and engine control module connector....3090
STEP 8. Check of the troubles....3091
Inspection Procedure 15: Vehicle power cannot be turned 'OFF' when the shift position is in 'P' (Power supply mode 'ON' to 'ACC' is possible)....3091
DIAGNOSIS....3091
STEP 1. Using scan tool MB991958, read the diagnostic trouble code.....3091
STEP 2. Check of short to ground in PDSW line between selector lever assembly connector and KOS&OSS-ECU connector.....3092
STEP 3. Check of selector lever assembly (P range detection switch).....3092
STEP 4. Using scan tool MB991958, check data list.....3093
Inspection Procedure 16: ACC power auto cut function does not work normally.....3093
DIAGNOSIS....3094
STEP 1. Check of customization.....3094
STEP 2. Using scan tool MB991958, read the diagnostic trouble code.....3094
STEP 3. Check of short to ground in PDSW line between selector lever assembly connector and KOS&OSS-ECU connector.....3094
STEP 4. Check of selector lever assembly (P range detection switch).....3095
STEP 5. Using scan tool MB991958, check data list.....3095
STEP 6. Using scan tool MB991958, check data list.....3096
STEP 7. Voltage measurement at KOS&OSS-ECU connector.....3096
STEP 8. Using scan tool MB991958, check data list.....3097
STEP 9.Check of the troubles.....3097
Inspection Procedure 17: Vehicle power cannot be turned OFF.....3097
DIAGNOSIS....3098
STEP 1. Using scan tool MB991958, diagnose the CAN bus line.....3098
STEP 2. Using scan tool MB991958, read the other system diagnostic trouble code.....3098
STEP 3. Using scan tool MB991958, check data list.....3099
STEP 4. IG1 relay check.....3099
STEP 5. Voltage measurement at IG1 relay connector (IG1 terminal)....3099
STEP 6. Check of short to power supply, short to ground or open circuit in IG1 line between the KOS&OSS-ECU connector and the IG1 relay connector....3100
STEP 7. Check of open circuit in ground line between the IG1 relay connector and the body ground....3100
STEP 8. Voltage measurement at IG1 relay connector (IG1 line and power supply line)....3100
STEP 9. Check of short to power supply, short to ground or open circuit in power supply line between the fusible link connector and the IG1 relay connector....3100
STEP 10. Voltage measurement at ETACS-ECU connector (IG1 line)....3101
STEP 11. Engine switch check....3101
STEP 12. Check of the troubles....3101
ON-VEHICLE SERVICE....3104
ANTENNA COMMUNICATION TEST....3105
KEYLESS ENTRY FUNCTION CHECK....3106
INSPECTION OF KEYLESS ENTRY TIMER LOCK FUNCTION....3106
CHECK OF ENGINE SWITCH REMINDER TONE ALARM....3107
RELAY INSPECTION....3110
ACC relay inspection....3110
IG1 relay inspection....3110
IG2 relay inspection....3111
KOS & OSS-ECU....3113
INSTALLATION SERVICE POINT....3113
OUTSIDE TRANSMISSION ANTENNA ASSEMBLY, INSIDE TRANSMISSION ANTENNA ASSEMBLY....3115
KEYLESS OPERATION KEY....3117
DISASSEMBLY SERVICE POINTS....3118
REASSEMBLY SERVICE POINT....3119
TPMS TRANSMITTER....3119
LOCK/UNLOCK SWITCH....3120
INSTALLATION SERVICE POINT....3121
INSPECTION....3121
LOCK/UNLOCK SWITCH CHECK....3121
KEY SLOT....3122
INSPECTION....3122
KEY SLOT INSPECTION....3122
ENGINE SWITCH....3123
INSPECTION....3123
GR00002800-70....3124
COMPONENT LOCATIONS....3124
RELAY....3125
CONTROL UNIT....3126
SENSOR....3129
SOLENOID AND SOLENOID VALVE....3134
FUSIBLE LINK, FUSE AND IOD OR STORAGE CONNECTOR....3136
INSPECTION TERMINAL....3138
GROUNDING CABLE....3139
GROUNDING....3140
GR00002900-80....3144
CONFIGURATION DIAGRAMS....3144
GR00003100-80B....3146
SPLICE LOCATIONS....3146
HOW TO READ SPLICE LOCATIONS....3147
INDEX....3148
ENGINE COMPARTMENT....3148
INSTRUMENT PANEL....3149
FLOOR....3150
DOOR....3151
LIFTGATE....3152
GR00003600-00E....3154
GENERAL <ELECTRICAL>....3154
HARNESS CONNECTOR INSPECTION....3155
CONNECTOR CONTINUITY AND VOLTAGE TEST....3155
IMPROPER TERMINAL ENGAGEMENT CHECK....3155
CONNECTOR TERMINAL ENGAGEMENT AND DISENGAGEMENT....3156
HOW TO DIAGNOSE....3159
INSPECTION....3160
INSPECTION INSTRUMENTS....3160
CHECKING FUSES....3162
CAUTIONS IN EVENT OF BLOWN FUSE....3162
CHECKING SWITCHES....3163
CHECKING RELAYS....3164
CABLES AND WIRES CHECK....3165
BATTERY HANDLING....3165
GENERAL ELECTRICAL SYSTEM CHECK....3165
STEP 1. Remove the blown fuse and connect the test light across the fuse terminals (Circuit switch: OFF).....3166
STEP 2. Turn the switch ON and disconnect the illumination light connector.....3167
GR00003700-00....3170
GENERAL....3170
GR00003800-51....3172
EXTERIOR....3172
FRONT BUMPER ASSEMBLY AND RADIATOR GRILLE....3174
DISASSEMBLY SERVICE POINT....3176
ASSEMBLY SERVICE POINT....3176
REAR BUMPER ASSEMBLY....3177
GARNISHES AND MOLDINGS....3178
REMOVAL SERVICE POINT....3178
DOOR SASH TAPE....3179
REMOVAL SERVICE POINT....3180
INSTALLATION SERVICE POINT....3181
SIDE AIR DAM....3183
REMOVAL SERVICE POINT....3184
INSTALLATION SERVICE POINT....3185
UNDER COVER....3186
LIFTGATE SPOILER....3187
WINDSHIELD WIPER AND WASHER....3187
TROUBLESHOOTING....3190
Inspection Procedure 1: Windshield wipers do not work at all.....3190
DIAGNOSIS....3191
STEP 1. Using scan tool (M.U.T.-III), read the diagnostic trouble code.....3191
STEP 2. Using scan tool (M.U.T.-III), check data list.....3191
STEP 3. Check the windshield wiper motor.....3192
STEP 4. Measure the resistance at windshield wiper motor connector.....3192
STEP 5. Check of open circuit in ground lines between windshield wiper motor connector and body ground.....3192
STEP 6. Measure the voltage at ETACS-ECU connector (+B terminal).....3193
STEP 7. Check of short to power supply, short to ground, and open circuit in power supply line between fusible link and ETACS-ECU connector (+B terminal).....3193
STEP 8.Check of short to power supply, short to ground, and open circuit in F/WIP LO,HI line between windshield wiper motor connector and ETACS-ECU connector....3193
STEP 9. Check the trouble symptom.....3193
Inspection Procedure 2: The windshield wipers do not work when the wiper switch is at the 'INT', 'Washer' or 'Mist' position. However, the wipers work at low speed when the switch is at the 'Lo' and 'Hi' position.....3193
DIAGNOSIS....3194
Inspection Procedure 3: The windshield wipers do not stop at the specified position.....3194
DIAGNOSIS....3194
STEP 1. Check the windshield wiper motor.....3194
STEP 2. Measure the voltage at windshield wiper motor connector.....3195
STEP 3. Check of short to power supply, short to ground, and open circuit in power supply line between windshield wiper motor connector and ignition switch (ACC).....3195
STEP 4. Check of short to power supply, short to ground, and open circuit in F/WIP AS, F/WIP ACC line between windshield wiper motor connector and ETACS-ECU connector....3195
STEP 5. Retest the system.....3195
Inspection Procedure 4: The windshield wipers do not work normally.....3195
DIAGNOSIS....3196
STEP 1. Using scan tool (M.U.T.-III), read the diagnostic trouble code.....3196
STEP 2. Using scan tool (M.U.T.-III), check data list.....3196
STEP 3. Check that the windshield wipers work.....3196
STEP 4. Check the windshield wiper motor.....3197
STEP 5.Check of short to power supply, short to ground, and open circuit in F/WIP LO line between windshield wiper motor connector and ETACS-ECU connector....3197
STEP 6. System retest....3197
STEP 7. Check the windshield wiper motor.....3198
STEP 8. Measure the voltage at windshield wiper motor connector.....3198
STEP 9. Check of short to power supply, short to ground, and open circuit in F/WIP HI line between windshield wiper motor connector and ETACS-ECU connector.....3198
STEP 10. System retest....3199
Inspection Procedure 5: The windshield intermittent wiper interval cannot be adjusted by operating the windshield intermittent wiper volume control.....3199
DIAGNOSIS....3199
STEP 1. Using scan tool (M.U.T.-III), read the diagnostic trouble code.....3199
STEP 2. Check the ETACS customization function.....3199
STEP 3. System retest....3200
Inspection Procedure 6: The intermittent wiper interval is not changed according to the vehicle speed.....3200
DIAGNOSIS....3200
STEP 1. Check the operation of windshield intermittent wiper volume control.....3200
STEP 2. Check the ETACS customization function.....3200
STEP 3. Using scan tool (M.U.T-III), diagnose the CAN bus line.....3201
STEP 4. Using scan tool (M.U.T.-III), read the diagnostic trouble code.....3201
STEP 5. Using scan tool (M.U.T.-III), read the other system diagnostic trouble code.....3201
STEP 6. Retest the system.....3202
Inspection Procedure 7: The windshield washer does not work normally.....3202
DIAGNOSIS....3202
STEP 1. Check the operation of the windshield wipers.....3202
STEP 2. Using scan tool (M.U.T.-III), read the diagnostic trouble code.....3202
STEP 3. Check the washer motor.....3203
STEP 4. Using scan tool (M.U.T.-III), check data list.....3203
STEP 5. Measure the voltage at the ETACS-ECU connector (F/WIP-WASH terminal).....3203
STEP 6. Check of short to power supply, short to ground, and open circuit in F/WIP WASH line between windshield washer motor connector and ETACS-ECU connector....3204
STEP 7. Check of short to power supply, short to ground, and open circuit in R/WIP WASH line between windshield washer motor connector and ETACS-ECU connector....3204
STEP 8. Check the trouble symptom.....3204
ON-VEHICLE SERVICE....3204
WINDSHIELD WIPER....3205
REMOVAL SERVICE POINT....3206
INSTALLATION SERVICE POINTS....3207
INSPECTION....3209
WINDSHIELD WIPER MOTOR CHECK....3209
WINDSHIELD WASHER....3210
INSPECTION....3211
WINDSHIELD WASHER MOTOR CHECK....3211
WINDSHIELD WASHER SWITCH CHECK....3211
WINDSHIELD WASHER FLUID EJECTION CHECK....3211
REAR WIPER AND WASHER....3213
EXTERIOR DIAGNOSIS....3215
Inspection Procedure 1: Rear wiper does not work at all.....3215
DIAGNOSIS....3216
STEP 1. Using scan tool (M.U.T.-III), read the diagnostic trouble code.....3216
STEP 2. Using scan tool (M.U.T.-III), check data list.....3216
STEP 3. Check the rear wiper motor.....3217
STEP 4. Measure the resistance at the rear wiper motor connector (ground terminal).....3217
STEP 5. Check of open circuit in ground line between rear wiper motor connector and body ground.....3217
STEP 6. Check of short to power supply, short to ground, and open circuit in RR WIP MTR line between rear wiper motor connector and ETACS-ECU connector.....3217
STEP 7. Retest the system.....3218
Inspection Procedure 2: The rear wiper does not stop at the specified park position.....3218
DIAGNOSIS....3218
STEP 1. Check the rear wiper motor.....3218
STEP 2. Measure the voltage at the rear wiper motor connector (ACC terminal).....3219
STEP 3.Check of short to power supply, short to ground, and open circuit in RR WIP AUTO STP, RR WIP ACC line between rear wiper motor connector and ETACS-ECU connector.....3219
STEP 4. Using scan tool (M.U.T.-III), check data list.....3219
Inspection Procedure 3: When the selector lever is moved to 'R' position during the rear wiper operation, the rear wiper does not operate at the continuous mode.....3220
DIAGNOSIS....3220
STEP 1. Check the operation of the rear wiper.....3220
STEP 2. Using scan tool (M.U.T.-III), read the diagnostic trouble code for other system.....3220
STEP 3. Retest the system.....3220
Inspection Procedure 4: The rear washer does not work normally.....3221
DIAGNOSIS....3221
STEP 1. Check that the windshield washers work.....3221
STEP 2. Using scan tool (M.U.T.-III), read the diagnostic trouble code.....3221
STEP 3. Using scan tool (M.U.T.-III), check data list.....3222
STEP 4. Check the rear washer motor.....3222
STEP 5. Retest the system.....3222
ON-VEHICLE SERVICE....3222
REAR WIPER AND WASHER....3224
INSTALLATION SERVICE POINTS....3225
INSPECTION....3226
REAR WIPER MOTOR CHECK....3226
REAR WASHER MOTOR INSPECTION....3226
CHECKING THE REAR WASHER NOZZLE INJECTION DIRECTION....3226
CHECKING THE REAR WIPER AND WASHER SWITCH....3228
MARK....3228
INSTALLATION SERVICE POINT....3230
DOOR MIRROR....3232
TROUBLESHOOTING....3234
Inspection Procedure 1: None of the heated door mirrors operate....3234
DIAGNOSIS....3235
STEP 1. Check the rear window defogger.....3235
Inspection Procedure 2: Either of the door mirror heater elements does not work.....3235
DIAGNOSIS....3235
STEP 1. Determine a trouble spot.....3235
STEP 2. Check of the heater element of the door mirror (RH)....3235
STEP 3. Measure the resistance at the door mirror assembly (RH) connector (ground terminal).....3236
STEP 4. Check of open circuit in ground line between the door mirror assembly (RH) connector and body ground.....3236
STEP 5. Measure the voltage at the door mirror assembly (RH) connector (power supply terminal).....3236
STEP 6. Check of short to power supply, short to ground, and open circuit in power supply line between door mirror assembly (RH) connector and ETACS-ECU connector.....3236
STEP 7. Retest the system.....3236
STEP 8. Check of the heater element of the door mirror (LH)....3237
STEP 9. Measure the resistance at the door mirror assembly (LH) connector (ground terminal).....3237
STEP 10. Check of open circuit in ground line between the door mirror assembly (LH) connector and body ground.....3237
STEP 11. Measure the voltage at the door mirror assembly (LH) connector (power supply terminal).....3238
STEP 12. Check of short to power supply, short to ground, and open circuit power supply line between door mirror assembly (LH) connector and ETACS-ECU connector.....3238
STEP 13. Retest the system.....3238
DOOR MIRROR....3239
REMOVAL SERVICE POINTS....3242
INSTALLATION SERVICE POINT....3244
INSPECTION....3244
DOOR MIRROR OPERATION CHECK....3244
DOOR MIRROR CONTROL SWITCH CONTINUITY CHECK....3245
HEATED DOOR MIRROR CHECK....3246
GR00003900-52B-sm....3248
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)....3248
GENERAL INFORMATION....3250
SERVICE PRECAUTIONS....3252
SPECIAL TOOLS....3255
TEST EQUIPMENTS....3257
SRS AIR BAG DIAGNOSIS....3258
HOW TO CONNECT THE SCAN TOOL (M.U.T.-III)....3258
HOW TO READ AND ERASE DIAGNOSTIC TROUBLE CODES....3259
HOW TO DIAGNOSE THE CAN BUS LINES....3260
SRS WARNING LIGHT CHECK....3261
PASSENGER' AIR BAG OFF INDICATOR LIGHT CHECK....3261
CHECK CHART FOR DIAGNOSTIC TROUBLE CODES....3261
DIAGNOSTIC TROUBLE CODE PROCEDURES <SRS-ECU>....3266
DTC B1400: Driver' air bag module (1st squib) system (short circuit between squib circuit terminals) DTC B1480: Driver' air bag module (2nd squib) system (short circuit between squib circuit terminals)....3266
DIAGNOSIS....3267
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3267
STEP 2. Recheck for diagnostic trouble code.....3267
STEP 3. Connector check: SRS-ECU, clock spring, driver' air bag module.....3268
STEP 4. Diagnosis check by dummy resistor connection.....3269
STEP 5. Diagnosis check by dummy resistor connection.....3270
STEP 6. Resistance measurement at the SRS-ECU connector.....3271
STEP 7. Recheck for diagnostic trouble code.....3271
DTC B1401: Driver' air bag module (1st squib) system (open circuit of squib circuit) DTC B1481: Driver' air bag module (2nd squib) system (open circuit of squib circuit)....3272
DIAGNOSIS....3273
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3273
STEP 2. Recheck for diagnostic trouble code.....3273
STEP 3. Check the diagnostic trouble code by connecting a dummy resistor.....3274
STEP 4. Diagnosis check by dummy resistor connection.....3275
STEP 5. Resistance measurement at the SRS-ECU and the C-313 clock spring connectors....3276
STEP 6. Recheck for diagnostic trouble code.....3277
DTC B1402: Driver' air bag module (1st squib) system (shorted to squib circuit ground) DTC B1482: Driver' air bag module (2nd squib) system (shorted to squib circuit ground)....3277
DIAGNOSIS....3278
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3278
STEP 2. Recheck for diagnostic trouble code.....3278
STEP 3. Check the diagnostic trouble code by connecting a dummy resistor.....3279
STEP 4. Diagnosis check by dummy resistor connection.....3280
STEP 5. Resistance measurement at the SRS-ECU connector.....3281
STEP 6. Recheck for diagnostic trouble code.....3282
DTC B1403: Driver' air bag module (1st squib) system (shorted to squib circuit power supply) DTC B1483: Driver' air bag module (2nd squib) system (shorted to squib circuit power supply)....3282
DIAGNOSIS....3283
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3283
STEP 2. Recheck for diagnostic trouble code.....3283
STEP 3. Check the diagnostic trouble code by connecting a dummy resistor.....3284
STEP 4. Diagnosis check by dummy resistor connection.....3285
STEP 5. Voltage measurement at the SRS-ECU connector.....3286
STEP 6. Recheck for diagnostic trouble code.....3286
DTC B1404: Driver' air bag module (1st squib) activating circuit short-circuited DTC B1405: Driver' air bag module (1st squib).....3287
DIAGNOSIS....3289
STEP 1. Using scan tool MB991958, diagnose the CAN bus line.....3289
STEP 2. Recheck for diagnostic trouble code.....3289
DTC B1406: Malfunction of front impact sensor (RH)....3289
DIAGNOSIS....3290
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3290
STEP 2. Check the front impact sensor (RH).....3290
STEP 3. Recheck for diagnostic trouble code.....3290
DTC B1407: Front Impact Sensor (RH) Voltage Error....3290
DIAGNOSIS....3291
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3291
STEP 2. Recheck for diagnostic trouble code.....3291
STEP 3. Check of short to power supply, short to ground, and open circuit in FRH-, FRH+ line between SRS-ECU connector and front impact sensor (RH) connector.....3291
STEP 4. Check the front impact sensor (RH).....3292
STEP 5. Recheck for diagnostic trouble code.....3292
DTC B1408: Front Impact Sensor (RH) Communication Error DTC B1409: Front Impact Sensor (RH) Communication Impossible....3292
DIAGNOSIS....3293
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3293
STEP 2. Recheck for diagnostic trouble code.....3293
STEP 3. Check the front impact sensor (RH).....3293
STEP 4. Check of short to power supply, short to ground, and open circuit in FRH-, FRH+ line between SRS-ECU connector and front impact sensor (RH) connector.....3293
STEP 5. Recheck for diagnostic trouble code.....3294
DTC B1410: Passenger' (front) air bag module (1st squib) system (short circuit between squib circuit terminals) DTC B1490: Passenger' (front) air bag module (2nd squib) system (short circuit between squib circuit terminals)....3294
DIAGNOSIS....3295
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3295
STEP 2. Recheck for diagnostic trouble code.....3295
STEP 3. Connector check: passenger' (front) air bag module, SRS-ECU.....3296
STEP 4. Diagnosis check by dummy resistor connection.....3297
STEP 5. Resistance measurement at the SRS-ECU connector.....3298
STEP 6. Check for diagnostic trouble code.....3299
DTC B1411: Passenger' (front) air bag module (1st squib) system (open circuit of squib circuit) DTC B1491: Passenger' (front) air bag module (2nd squib) system (squib circuit open)....3299
DIAGNOSIS....3299
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3299
STEP 2. Recheck for diagnostic trouble code.....3300
STEP 3. Diagnosis check by dummy resistor connection.....3300
STEP 4. Resistance measurement at the SRS-ECU connector and the passenger' (front) air bag module connector.....3301
STEP 5. Recheck for diagnostic trouble code.....3302
DTC B1412: Passenger' (front) air bag module (1st squib) system (shorted to squib circuit ground) DTC B1492: Passenger' (front) air bag module (2nd squib) system (shorted to squib circuit ground)....3302
DIAGNOSIS....3303
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3303
STEP 2. Recheck for diagnostic trouble code.....3303
STEP 3. Diagnosis check by dummy resistor connection.....3304
STEP 4. Resistance measurement at the SRS-ECU connector.....3305
STEP 5. Recheck for diagnostic trouble code.....3306
DTC B1413: Passenger' (front) air bag module (1st squib) system (shorted to squib circuit power supply) DTC B1493: Passenger' (front) air bag module (2nd squib) system (shorted to squib circuit power supply....3306
DIAGNOSIS....3306
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3306
STEP 2. Recheck for diagnostic trouble code.....3307
STEP 3. Diagnosis check by dummy resistor connection.....3307
STEP 4. Voltage measurement at the SRS-ECU connector.....3308
STEP 5. Recheck for diagnostic trouble code.....3309
DTC B1416: Malfunction of front impact sensor (LH)....3309
DIAGNOSIS....3309
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3309
STEP 2. Check the front impact sensor (LH).....3310
STEP 3. Recheck for diagnostic trouble code.....3310
DTC B1417: Front impact sensor (LH) voltage error....3310
DIAGNOSIS....3311
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3311
STEP 2. Recheck for diagnostic trouble code.....3311
STEP 3. Check of short to power supply, short to ground, and open circuit in FLH-, FLH+ line between SRS-ECU connector and front impact sensor (LH) connector.....3311
STEP 4. Check the front impact sensor (LH).....3311
STEP 5. Recheck for diagnostic trouble code.....3312
DTC B1418: Front impact sensor (LH) communication error DTC B1419: Front impact sensor (LH) communication impossible....3312
DIAGNOSIS....3312
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3312
STEP 2. Recheck for diagnostic trouble code.....3313
STEP 3. Check the front impact sensor (LH).....3313
STEP 4. Check of short to power supply, short to ground, and open circuit in FLH-, FLH+ line between SRS-ECU connector and front impact sensor (LH) connector.....3313
STEP 5. Recheck for diagnostic trouble code.....3313
DTC B1420: Side-airbag module (RH) (squib) system (short circuit between squib terminals)....3314
DIAGNOSIS....3314
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3314
STEP 2. Recheck for diagnostic trouble code.....3314
STEP 3. Connector check: SRS-ECU, side-airbag module (RH).....3315
STEP 4. Diagnosis check by dummy resistor connection.....3316
STEP 5. Resistance measurement at the SRS-ECU connector.....3317
STEP 6. Recheck for diagnostic trouble code.....3317
DTC B1421: Side-airbag module (RH) (squib) system (open circuit of squib circuit)....3318
DIAGNOSIS....3318
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3318
STEP 2. Recheck for diagnostic trouble code.....3318
STEP 3. Check the side-airbag module (RH).....3319
STEP 4. Resistance measurement at the SRS-ECU connector and the side-airbag module (RH) connector.....3320
STEP 5. Recheck for diagnostic trouble code.....3321
DTC B1422: Side-airbag module (RH) (squib) system (shorted to squib circuit ground)....3321
DIAGNOSIS....3321
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3321
STEP 2. Recheck for diagnostic trouble code.....3322
STEP 3. Check the side-airbag module (RH).....3322
STEP 4. Resistance measurement at the SRS-ECU connector.....3323
STEP 5. Recheck for diagnostic trouble code.....3323
DTC B1423: Side-airbag module (RH) (squib) system (shorted to squib circuit power supply)....3324
DIAGNOSIS....3324
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3324
STEP 2. Recheck for diagnostic trouble code.....3324
STEP 3. Check the side-airbag module (RH).....3325
STEP 4. Voltage measurement at the SRS-ECU connector.....3326
STEP 5. Recheck for diagnostic trouble code.....3327
DTC B1426: Malfunction of Side Impact Sensor (RH) DTC B1436: Malfunction of Side Impact Sensor (LH)....3327
DIAGNOSIS....3327
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3327
STEP 2. Side impact sensor check.....3328
STEP 3. Recheck for diagnostic trouble code.....3328
DTC B1427: Side impact sensor (RH) voltage error....3328
DIAGNOSIS....3329
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3329
STEP 2. Recheck for diagnostic trouble code.....3329
STEP 3. Check of short to power supply, short to ground, and open circuit in SSR-, SSR+ line in between SRS-ECU connector and side impact sensor (RH) connector.....3329
STEP 4. Check the side impact sensor (RH).....3329
STEP 5. Recheck for diagnostic trouble code.....3330
DTC B1428: Side impact sensor (RH) communication error DTC B1429: Side impact sensor (RH) communication impossible....3330
DIAGNOSIS....3330
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3330
STEP 2. Recheck for diagnostic trouble code.....3331
STEP 3. Right side impact sensor check.....3331
STEP 4. Check of short to power supply, short to ground, and open circuit in SSR-, SSR+ line in between SRS-ECU connector and side impact sensor (RH) connector.....3331
STEP 5. Check whether the DTC is stored again.....3331
DTC B1430: Side-airbag module (LH) (squib) system (short circuit between squib terminals)....3332
DIAGNOSIS....3332
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3332
STEP 2. Recheck for diagnostic trouble code.....3333
STEP 3. Connector check: SRS-ECU, side-airbag module (LH).....3333
STEP 4. Diagnosis check by dummy resistor connection.....3334
STEP 5. Resistance measurement at the SRS-ECU connector.....3335
STEP 6. Recheck for diagnostic trouble code.....3335
DTC B1431: Side-airbag module (LH) (squib) system (open circuit of squib circuit)....3336
DIAGNOSIS....3336
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3336
STEP 2. Recheck for diagnostic trouble code.....3336
STEP 3. Diagnosis check by dummy resistor connection.....3337
STEP 4. Resistance measurement at the SRS-ECU connector and the side-airbag module (LH) connector.....3338
STEP 5. Recheck for diagnostic trouble code.....3339
DTC B1432: Side-airbag module (LH) (squib) system (shorted to squib circuit earth)....3339
DIAGNOSIS....3339
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3339
STEP 2. Recheck for diagnostic trouble code.....3340
STEP 3. Diagnosis check by dummy resistor connection.....3340
STEP 4. Resistance measurement at the SRS-ECU connector.....3341
STEP 5. Recheck for diagnostic trouble code.....3342
DTC B1433: Side-airbag module (LH) (squib) system (shorted to squib circuit power supply)....3342
DIAGNOSIS....3342
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3342
STEP 2. Recheck for diagnostic trouble code.....3343
STEP 3. Diagnosis check by dummy resistor connection.....3343
STEP 4. Voltage measurement at the SRS-ECU connector.....3344
STEP 5. Recheck for diagnostic trouble code.....3345
DTC B1437: Side impact sensor (LH) voltage error....3345
DIAGNOSIS....3345
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3345
STEP 2. Recheck for diagnostic trouble code.....3346
STEP 3. Check of short to power supply, short to ground, and open circuit in SSL+, SSL- line in between SRS-ECU connector and side impact sensor (LH) connector.....3346
STEP 4. Check the side impact sensor (LH).....3346
STEP 5. Check whether the DTC is reset.....3346
DTC B1438: Side impact sensor (LH) communication error DTC B1439: Side impact sensor (LH) communication impossible....3347
DIAGNOSIS....3347
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3347
STEP 2. Recheck for diagnostic trouble code.....3347
STEP 3. Check the side impact sensor (LH).....3348
STEP 4. Check of short to power supply, short to ground, and open circuit in SSL+, SSL- line in between SRS-ECU connector and side impact sensor (LH) connector.....3348
STEP 5. Check whether the DTC is reset.....3348
DTC B1440: Curtain air bag module (RH) (squib) system (short circuit between squib circuit terminals)....3348
DIAGNOSIS....3349
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3349
STEP 2. Recheck for diagnostic trouble code.....3349
STEP 3. Connector check: SRS-ECU, curtain air bag module (RH).....3350
STEP 4. Diagnosis check by dummy resistor connection.....3350
STEP 5. Resistance measurement at the SRS-ECU connector.....3351
STEP 6. Recheck for diagnostic trouble code.....3351
DTC B1441: Curtain air bag module (RH) (squib) system (open circuit of squib circuit)....3352
DIAGNOSIS....3352
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3352
STEP 2. Recheck for diagnostic trouble code.....3352
STEP 3. Diagnosis check by dummy resistor connection.....3353
STEP 4. Resistance measurement at the SRS-ECU connector and the curtain air bag module (RH) connector.....3354
STEP 5. Recheck for diagnostic trouble code.....3355
DTC B1442: Curtain air bag module (RH) (squib) system (shorted to squib circuit ground)....3355
DIAGNOSIS....3356
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3356
STEP 2. Recheck for diagnostic trouble code.....3356
STEP 3. Diagnosis check by dummy resistor connection....3357
STEP 4. Resistance measurement at the SRS-ECU connector.....3358
STEP 5. Recheck for diagnostic trouble code.....3358
DTC B1443: Curtain air bag module (RH) (squib) system (shorted to squib circuit power supply)....3359
DIAGNOSIS....3359
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3359
STEP 2. Recheck for diagnostic trouble code.....3359
STEP 3. Diagnosis check by dummy resistor connection....3360
STEP 4. Voltage measurement at the SRS-ECU connector.....3361
STEP 5. Recheck for diagnostic trouble code.....3361
DTC B1450: Curtain air bag module (LH) (squib) system (short circuit between squib circuit terminals)....3362
DIAGNOSIS....3362
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3362
STEP 2. Recheck for diagnostic trouble code.....3363
STEP 3. Connector check: SRS-ECU, curtain air bag module (LH) connector.....3363
STEP 4. Diagnosis check by dummy resistor connection.....3364
STEP 5. Resistance measurement at the SRS-ECU connector.....3365
STEP 6. Recheck for diagnostic trouble code.....3365
DTC B1451: Curtain air bag module (LH) (squib) system (open circuit of squib circuit)....3366
DIAGNOSIS....3366
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3366
STEP 2. Recheck for diagnostic trouble code.....3366
STEP 3. Diagnosis check by dummy resistor connection.....3367
STEP 4. Resistance measurement at the SRS-ECU connector and the curtain air bag module (LH) connector.....3368
STEP 5. Recheck for diagnostic trouble code.....3369
DTC B1452: Curtain air bag module (LH) (squib) system (shorted to squib circuit ground)....3369
DIAGNOSIS....3370
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3370
STEP 2. Recheck for diagnostic trouble code.....3370
STEP 3. Diagnosis check by dummy resistor connection....3371
STEP 4. Resistance measurement at the SRS-ECU connector.....3372
STEP 5. Recheck for diagnostic trouble code.....3372
DTC B1453: Curtain air bag module (LH) (squib) system (shorted to squib circuit power supply)....3373
DIAGNOSIS....3373
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3373
STEP 2. Recheck for diagnostic trouble code.....3373
STEP 3. Diagnosis check by dummy resistor connection....3374
STEP 4. Voltage measurement at the SRS-ECU connector.....3375
STEP 5. Recheck for diagnostic trouble code.....3375
DTC B1476: IG1 power supply open circuit (Fuse No. 15 circuit) DTC B1477: IG1 power supply open circuit (Fuse No. 21 circuit)....3376
DIAGNOSIS....3376
STEP 1. Power supply fuse check.....3376
STEP 2. Fuse open circuit check....3376
STEP 3. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3377
STEP 4. Using scan tool (M.U.T.-III), check data list.....3377
STEP 5. Recheck for diagnostic trouble code.....3377
STEP 6. Resistance measurement at the SRS-ECU connector.....3378
STEP 7. Voltage measurement at the SRS-ECU connector (IG1A, IG1B line).....3378
STEP 8. Resistance measurement at the SRS-ECU connector.....3379
STEP 9. Recheck for diagnostic trouble code.....3379
DTC B1488: Passenger' air bag OFF indicator light (short circuited)....3379
DIAGNOSIS....3380
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3380
STEP 2. Recheck for diagnostic trouble code.....3380
STEP 3. Check the passenger’s air bag OFF indicator light.....3380
STEP 4. Resistance measurement at the SRS-ECU connector.....3381
STEP 5. Recheck for diagnostic trouble code.....3381
DTC B1489: Passenger’s air bag OFF indicator light (open circuit)....3381
DIAGNOSIS....3382
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3382
STEP 2. Recheck for diagnostic trouble code.....3382
STEP 3. Check the passenger’s air bag OFF indicator light.....3382
STEP 4. Resistance measurement at the SRS-ECU connector and the passenger’s air bag OFF indicator light connector.....3383
STEP 5. Measure the voltage at the passenger’s air bag OFF indicator light connector.....3383
STEP 6. Recheck for diagnostic trouble code.....3383
DTC B1499: Air bag deployment determined by SRS-ECU....3384
DIAGNOSIS....3384
DTC B1509: Incorrect installation of SRS-ECU....3384
DIAGNOSIS....3384
DTC B1530: Seat Belt Switch (Passenger’s side) Malfunction DTC B1537: Seat Belt Switch (Passenger’s side) Circuit Open DTC B15....3384
DIAGNOSIS....3385
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3385
STEP 2. Recheck for diagnostic trouble code.....3385
STEP 3. Seat belt switch (passenger’s side) check.....3385
STEP 4. Check the harness short circuit between seat belt switch (passenger’s side) connector and the SRS-ECU connector.....3386
STEP 5. Resistance measurement at the SRS-ECU connector and the seat belt switch (passenger’s side) connector.....3387
STEP 6. Recheck for diagnostic trouble code.....3387
DTC B1558: OCM (Occupant Classification-ECU) DTC Present....3388
DIAGNOSIS....3388
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3388
STEP 2. Recheck for diagnostic trouble code.....3388
STEP 3. Recheck for diagnostic trouble code.....3388
STEP 4. Recheck for diagnostic trouble code.....3389
DTC B1603: Seat belt pre-tensioner (driver’s side) (squib) system (short circuit between squib circuit terminals)....3389
DIAGNOSIS....3390
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3390
STEP 2. Recheck for diagnostic trouble code.....3390
STEP 3. Connector check: SRS-ECU connector, seat belt pre-tensioner (driver’s side) connector.....3391
STEP 4. Diagnosis check by dummy resistor connection.....3391
STEP 5. Resistance check at the SRS-ECU connector (PTD+, PTD- line).....3392
STEP 6. Recheck for diagnostic trouble code.....3393
DTC B1604: Seat belt pre-tensioner (driver’s side) (squib) system (open circuit of squib circuit)....3393
DIAGNOSIS....3393
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3393
STEP 2. Recheck for diagnostic trouble code.....3394
STEP 3. Diagnosis check by dummy resistor connection.....3394
STEP 4. Resistance measurement at the SRS-ECU connector and the seat belt pre-tensioner (driver’s side) connector.....3395
STEP 5. Recheck for diagnostic trouble code.....3396
DTC B1605: Seat belt pre-tensioner (driver’s side) (squib) system (shorted to squib circuit ground)....3396
DIAGNOSIS....3396
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3396
STEP 2. Recheck for diagnostic trouble code.....3397
STEP 3. Diagnosis check by dummy resistor connection.....3397
STEP 4. Resistance measurement at the SRS-ECU connector.....3398
STEP 5. Recheck for diagnostic trouble code.....3399
DTC B1606: Seat belt pre-tensioner (driver’s side) (squib) system (shorted to squib circuit power supply)....3399
DIAGNOSIS....3399
STEP 1. Using scan tool MB991958, diagnose the CAN bus line.....3399
STEP 2. Recheck for diagnostic trouble code.....3400
STEP 3. Diagnosis check by dummy resistor connection.....3400
STEP 4. Voltage measurement at the SRS-ECU connector.....3401
STEP 5. Recheck for diagnostic trouble code.....3402
DTC B1609: Seat belt pre-tensioner (passenger’s side) (squib) system (short circuit between squib circuit terminals)....3402
DIAGNOSIS....3402
STEP 1. Using scan tool MB991958, diagnose the CAN bus line.....3402
STEP 2. Recheck for diagnostic trouble code.....3403
STEP 3. Connector check: SRS-ECU, seat belt pre-tensioner (passenger' side).....3403
STEP 4. Diagnosis check by dummy resistor connection.....3404
STEP 5. Resistance check at the SRS-ECU connector.....3405
STEP 6. Recheck for diagnostic trouble code.....3405
DTC B1610: Seat belt pre-tensioner (passenger’s side) (squib) system (open circuit of squib circuit)....3406
DIAGNOSIS....3406
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3406
STEP 2. Recheck for diagnostic trouble code.....3406
STEP 3. Diagnosis check by dummy resistor connection.....3407
STEP 4. Resistance measurement at the SRS-ECU connector and the seat belt pre-tensioner (passenger' side) connector.....3408
STEP 5. Recheck for diagnostic trouble code.....3409
DTC B1611: Seat belt pre-tensioner (passenger’s side) (squib) system (shorted to squib circuit ground)....3409
DIAGNOSIS....3410
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3410
STEP 2. Recheck for diagnostic trouble code.....3410
STEP 3. Diagnosis check by dummy resistor connection.....3411
STEP 4. Resistance measurement at the SRS-ECU connector.....3412
STEP 5. Recheck for diagnostic trouble code.....3412
DTC B1612: Seat belt pre-tensioner (passenger’s side) (squib) system (shorted to squib circuit power supply)....3413
DIAGNOSIS....3413
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3413
STEP 2. Recheck for diagnostic trouble code.....3413
STEP 3. Diagnosis check by dummy resistor connection.....3414
STEP 4. Voltage measurement at the SRS-ECU connector.....3415
STEP 5. Recheck for diagnostic trouble code.....3416
DTC B1631: Driver' knee air bag module (squib) system (short circuit between squib circuit terminals)....3416
DIAGNOSIS....3417
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3417
STEP 2. Recheck for diagnostic trouble code.....3417
STEP 3. Connector check: SRS-ECU, knee air bag module.....3418
STEP 4. Diagnosis check by dummy resistor connection.....3418
STEP 5. Resistance check at the SRS-ECU connector.....3419
STEP 6. Recheck for diagnostic trouble code.....3419
DTC B1632: Driver' knee air bag module (squib) system (open circuit of squib circuit)....3420
DIAGNOSIS....3420
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3420
STEP 2. Recheck for diagnostic trouble code.....3420
STEP 3. Diagnosis check by dummy resistor connection.....3421
STEP 4. Resistance measurement at the SRS-ECU connector and the knee air bag module connector.....3422
STEP 5. Recheck for diagnostic trouble code.....3423
DTC B1633: Driver' knee air bag module (squib) system (shorted to squib circuit ground)....3423
DIAGNOSIS....3424
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3424
STEP 2. Recheck for diagnostic trouble code.....3424
STEP 3. Diagnosis check by dummy resistor connection.....3425
STEP 4. Resistance measurement at the SRS-ECU connector.....3426
STEP 5. Recheck for diagnostic trouble code.....3426
DTC B1634: Driver' knee air bag module (squib) system (shorted to squib circuit power supply)....3427
DIAGNOSIS....3427
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3427
STEP 2. Recheck for diagnostic trouble code.....3427
STEP 3. Diagnosis check by dummy resistor connection.....3428
STEP 4. Voltage measurement at the SRS-ECU connector.....3429
STEP 5. Recheck for diagnostic trouble code.....3430
DTC B1646: Coding data mismatch....3430
DTC B1699: SRS-ECU collective deployment....3430
DTC U0154: Occupant Classification-ECU CAN timeout....3430
DIAGNOSIS....3431
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line....3431
STEP 2. Using scan tool (M.U.T.-III), read the occupant classification-ECU diagnostic trouble code.....3431
STEP 3. Using scan tool (M.U.T.-III), read diagnostic trouble code No. U0154 for other system.....3431
STEP 4. Recheck for diagnostic trouble code.....3432
DTC U1100: Engine CAN timeout....3432
DIAGNOSIS....3432
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line....3432
STEP 2. Using scan tool (M.U.T.-III), read the other systems diagnostic trouble code.....3433
STEP 3. Using scan tool (M.U.T.-III), read the other systems diagnostic trouble code.....3433
STEP 4. Check whether the diagnostic trouble code is stored again.....3433
STEP 5. Check whether the diagnostic trouble code is stored again.....3433
STEP 6. Recheck for diagnostic trouble code.....3434
DTC U1102: ASC/TCL/ABS timeout/Not equipped....3434
DIAGNOSIS....3434
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3434
STEP 2. Using scan tool (M.U.T.-III), read the ASC-ECU diagnostic trouble code.....3435
STEP 3. Using scan tool (M.U.T.-III), read the ETACS diagnostic trouble code.....3435
STEP 4. Recheck for diagnostic trouble code.....3435
STEP 5. Recheck for diagnostic trouble code.....3435
STEP 6. Recheck for diagnostic trouble code.....3436
DTC U1104: SAS CAN timeout/Not equipped....3436
DIAGNOSIS....3436
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3436
STEP 2. Using scan tool (M.U.T.-III), read the EPS-ECU diagnostic trouble code....3436
STEP 3. Using scan tool (M.U.T.-III), read diagnostic trouble code No. U1104 for other system.....3437
STEP 4. Recheck for diagnostic trouble code.....3437
DTC U1108: Combination Meter CAN timeout....3437
DIAGNOSIS....3438
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3438
STEP 2. Using scan tool (M.U.T.-III), read the combination meter diagnostic trouble code....3438
STEP 3. Using scan tool (M.U.T.-III), read diagnostic trouble code No. U1108 for other system.....3438
STEP 4. Recheck for diagnostic trouble code.....3438
DTC U1109: ETACS CAN timeout....3439
DIAGNOSIS....3439
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line....3439
STEP 2. Using scan tool (M.U.T.-III), read the ETACS-ECU diagnostic trouble code....3439
STEP 3. Using scan tool (M.U.T.-III), read diagnostic trouble code No. U1109 for other system.....3439
STEP 4. Recheck for diagnostic trouble code.....3440
DTC U1190: No receive fault detect signal....3440
DIAGNOSIS....3440
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line....3440
STEP 2. Recheck for diagnostic trouble code.....3441
STEP 3. Recheck for diagnostic trouble code.....3441
STEP 4. Recheck for diagnostic trouble code.....3441
DTC U1195: Coding not completed....3441
DIAGNOSIS....3441
DTC U1199: VIN code not programmed....3442
DIAGNOSIS....3442
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3442
STEP 2. Register the VIN and recheck the diagnostic trouble code.....3442
DTC U119A: VIN code mismatch....3443
DIAGNOSIS....3443
STEP 1. Check the VIN registered in the engine control module and the VIN of the vehicle.....3443
STEP 2. Recheck for diagnostic trouble code.....3443
STEP 3. Recheck for diagnostic trouble code.....3443
DIAGNOSTIC TROUBLE CODE PROCEDURES <OCCUPANT CLASSIFICATION-ECU>....3444
DTC B1690: Electromagnetic Interference....3444
DIAGNOSIS....3445
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3445
STEP 2. Check whether any electronic appliance has been put on the front passenger' seat.....3445
STEP 3. Recheck for diagnostic trouble code.....3445
DTC B1691: Occupant Sensing Antenna DTC B1693: Occupant Sensing Antenna Open DTC B1694: Occupant Sensing ANT.SHT to GND DTC B1695: Occupant Sensing ANT.SHT to BAT....3446
DIAGNOSIS....3446
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3446
STEP 2. Check whether the front passenger' seat is damped with liquid or steam.....3446
STEP 3. Recheck for diagnostic trouble code.....3447
STEP 4. Check open circuit in GND line between occupant classification-ECU connector and body ground.....3447
STEP 5. Check of short to power supply, short to ground, and open circuit in SENSE, GUARD line between occupant classification-ECU connector and occupant classification sensor connector.....3447
STEP 6. Recheck for diagnostic trouble code.....3447
DTC B1CB2: Occupant Classification-ECU Parameter Table Incompatible....3448
DIAGNOSIS....3448
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3448
STEP 2. Recheck for diagnostic trouble code.....3448
DTC B210D: Battery Voltage Low DTC B210E: Battery Voltage High....3449
DIAGNOSIS....3449
STEP 1. Measure the voltage at the occupant classification-ECU connector.....3449
STEP 2. Power supply fuse No.21 check.....3449
STEP 3. Check of short to power supply, short to ground, and open circuit in BTT line between junction block connector and the occupant classification-ECU connector.....3449
STEP 4. Battery check.....3450
STEP 5. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3450
STEP 6. Recheck for diagnostic trouble code.....3450
STEP 7. Recheck for diagnostic trouble code.....3450
DTC B2212 OCM internal error....3451
DIAGNOSIS....3451
Recheck for diagnostic trouble code.....3451
DTC U1109: ETACS CAN Timeout....3451
DIAGNOSIS....3452
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line....3452
STEP 2. Using scan tool (M.U.T.-III), read the ETACS-ECU diagnostic trouble code....3452
STEP 3. Using scan tool (M.U.T.-III), read diagnostic trouble code No. U1109 for other system.....3452
STEP 4. Recheck for diagnostic trouble code.....3452
DTC U1190: No receive fault detect signal....3453
DIAGNOSIS....3453
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line....3453
STEP 2. Recheck for diagnostic trouble code.....3453
STEP 3. Recheck for diagnostic trouble code.....3454
STEP 4. Recheck for diagnostic trouble code.....3454
DTC U15A2 Vehicle speed information lost....3454
DIAGNOSIS....3455
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3455
STEP 2. Using scan tool (M.U.T.-III), check for any ASC diagnostic trouble code.....3455
STEP 3. Using scan tool (M.U.T.-III), read the KOS-ECU diagnostic trouble code.....3455
STEP 4. Recheck for diagnostic trouble code.....3455
STEP 5. Recheck for diagnostic trouble code.....3456
DTC U15A3 Odometer information lost....3456
DIAGNOSIS....3457
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3457
STEP 2. Using scan tool (M.U.T.-III), read the combination meter diagnostic trouble code....3457
STEP 3. Using scan tool (M.U.T.-III), read diagnostic trouble code No. U1108 for other system.....3457
STEP 4. Recheck for diagnostic trouble code.....3457
DTC U15A4 VIN information lost....3458
DIAGNOSIS....3458
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3458
STEP 2. Using scan tool (M.U.T.-III), read the engine control module diagnostic trouble code....3458
STEP 3. Check whether the diagnostic trouble code is stored again.....3459
STEP 4. Check whether the diagnostic trouble code is stored again.....3459
STEP 5. Check whether the diagnostic trouble code is stored again.....3459
SYMPTOM PROCEDURES....3460
Inspection Procedure 1: Communication between scan tool and SRS-ECU cannot be established.....3460
DIAGNOSIS....3460
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3460
Inspection Procedure 2: Power supply circuit system....3460
DIAGNOSIS....3461
STEP 1. Fuse Nos. 15, 21 check.....3461
STEP 2. Fuse open circuit check....3461
STEP 3. Check of open circuit in GND1 line between SRS-ECU and body ground.....3461
STEP 4. Check of short to power supply, short to ground, and open circuit in IG1A, IG1B line between SRS-ECU and junction block.....3461
STEP 5. Trouble symptom check.....3462
Inspection Procedure 3: SRS warning light does not illuminate.....3462
DIAGNOSIS....3462
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3462
STEP 2. Using scan tool (M.U.T.-III), actuator test....3462
STEP 3. Using scan tool (M.U.T.-III), actuator test....3463
STEP 4. Check of short to power supply, short to ground, and open circuit in IG1 line between junction block connector and combination meter connector....3463
STEP 5. Recheck of the SRS warning light....3463
Inspection Procedure 4: The SRS warning light does not go out.....3463
DIAGNOSIS....3464
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3464
STEP 2. Recheck of the SRS warning light....3464
STEP 3. Using scan tool (M.U.T.-III), actuator test.....3464
STEP 4. Check for diagnostic trouble code.....3464
STEP 5. Recheck of the SRS warning light....3464
FAIL-SAFE FUNCTION REFERENCE TABLE....3465
POST-COLLISION DIAGNOSIS....3465
SRS-ECU MEMORY CHECK....3465
REPAIR PROCEDURE....3467
INDIVIDUAL COMPONENT SERVICE....3471
WARNING/CAUTION LABELS....3472
FRONT IMPACT SENSORS....3473
REMOVAL SERVICE POINT....3474
INSTALLATION SERVICE POINTS....3474
INSPECTION....3475
SRS CONTROL UNIT (SRS-ECU)....3476
REMOVAL SERVICE POINTS....3477
INSTALLATION SERVICE POINTS....3477
INSPECTION....3478
DRIVER' AIR BAG MODULE AND CLOCK SPRING....3479
REMOVAL SERVICE POINTS....3480
INSTALLATION SERVICE POINTS....3483
INSPECTION....3485
PASSENGER' (FRONT) AIR BAG MODULE....3487
REMOVAL SERVICE POINTS....3488
INSTALLATION SERVICE POINTS....3488
SIDE-AIRBAG MODULE(S)....3490
REMOVAL SERVICE POINT....3491
INSTALLATION SERVICE POINTS....3491
INSPECTION....3493
FRONT SEATBACK ASSEMBLY WITH SIDE-AIRBAG MODULE CHECK....3493
CURTAIN AIR BAG MODULE(S)....3494
REMOVAL SERVICE POINTS....3495
INSTALLATION SERVICE POINTS....3496
INSPECTION....3497
CURTAIN AIR BAG MODULE CHECK....3497
KNEE AIR BAG MODULE....3498
REMOVAL SERVICE POINTS....3499
INSTALLATION SERVICE POINTS....3500
INSPECTION....3501
KNEE AIR BAG MODULE CHECK....3501
SIDE IMPACT SENSOR....3502
REMOVAL SERVICE POINTS....3503
INSTALLATION SERVICE POINTS....3503
INSPECTION....3504
SEAT BELTS WITH PRE-TENSIONER....3505
REMOVAL SERVICE POINTS....3507
INSTALLATION SERVICE POINTS....3507
INSPECTION....3508
SEAT BELT WITH PRE-TENSIONER CHECK....3508
OCCUPANT CLASSIFICATION-ECU....3509
REMOVAL SERVICE POINT....3510
INSTALLATION SERVICE POINTS....3510
INSPECTION....3510
OCCUPANT CLASSIFICATION SENSOR....3511
REMOVAL SERVICE POINT....3512
INSTALLATION SERVICE POINTS....3512
INSPECTION....3512
PASSENGER' AIR BAG ON/OFF INDICATOR LIGHT....3513
REMOVAL SERVICE POINT....3514
INSTALLATION SERVICE POINTS....3514
INSPECTION....3515
AIR BAG MODULE DISPOSAL PROCEDURES....3515
DISPOSAL OF UNDEPLOYED AIR BAG MODULES....3516
DISCARD OF DEPLOYED AIR BAG MODULE....3531
SEAT BELT PRE-TENSIONER DISPOSAL PROCEDURES....3532
UNDEPLOYED SEAT BELT WITH PRE-TENSIONER DISPOSAL....3532
DISCARD OF DEPLOYED SEAT BELT WITH PRE-TENSIONER....3535
GR00003900-52B....3536
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)....3536
GENERAL INFORMATION....3538
SERVICE PRECAUTIONS....3540
SPECIAL TOOLS....3543
TEST EQUIPMENTS....3545
SRS AIR BAG DIAGNOSIS....3546
HOW TO CONNECT THE SCAN TOOL (M.U.T.-III)....3546
HOW TO READ AND ERASE DIAGNOSTIC TROUBLE CODES....3547
HOW TO DIAGNOSE THE CAN BUS LINES....3548
SRS WARNING LIGHT CHECK....3549
PASSENGER' AIR BAG OFF INDICATOR LIGHT CHECK....3549
CHECK CHART FOR DIAGNOSTIC TROUBLE CODES....3549
DIAGNOSTIC TROUBLE CODE PROCEDURES <SRS-ECU>....3554
DTC B1400: Driver' air bag module (1st squib) system (short circuit between squib circuit terminals) DTC B1480: Driver' air bag module (2nd squib) system (short circuit between squib circuit terminals)....3554
DIAGNOSIS....3555
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3555
STEP 2. Recheck for diagnostic trouble code.....3555
STEP 3. Connector check: SRS-ECU, clock spring, driver' air bag module.....3556
STEP 4. Diagnosis check by dummy resistor connection.....3557
STEP 5. Diagnosis check by dummy resistor connection.....3558
STEP 6. Resistance measurement at the SRS-ECU connector.....3559
STEP 7. Recheck for diagnostic trouble code.....3559
DTC B1401: Driver' air bag module (1st squib) system (open circuit of squib circuit) DTC B1481: Driver' air bag module (2nd squib) system (open circuit of squib circuit)....3560
DIAGNOSIS....3561
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3561
STEP 2. Recheck for diagnostic trouble code.....3561
STEP 3. Check the diagnostic trouble code by connecting a dummy resistor.....3562
STEP 4. Diagnosis check by dummy resistor connection.....3563
STEP 5. Resistance measurement at the SRS-ECU and the C-313 clock spring connectors....3564
STEP 6. Recheck for diagnostic trouble code.....3565
DTC B1402: Driver' air bag module (1st squib) system (shorted to squib circuit ground) DTC B1482: Driver' air bag module (2nd squib) system (shorted to squib circuit ground)....3565
DIAGNOSIS....3566
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3566
STEP 2. Recheck for diagnostic trouble code.....3566
STEP 3. Check the diagnostic trouble code by connecting a dummy resistor.....3567
STEP 4. Diagnosis check by dummy resistor connection.....3568
STEP 5. Resistance measurement at the SRS-ECU connector.....3569
STEP 6. Recheck for diagnostic trouble code.....3570
DTC B1403: Driver' air bag module (1st squib) system (shorted to squib circuit power supply) DTC B1483: Driver' air bag module (2nd squib) system (shorted to squib circuit power supply)....3570
DIAGNOSIS....3571
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3571
STEP 2. Recheck for diagnostic trouble code.....3571
STEP 3. Check the diagnostic trouble code by connecting a dummy resistor.....3572
STEP 4. Diagnosis check by dummy resistor connection.....3573
STEP 5. Voltage measurement at the SRS-ECU connector.....3574
STEP 6. Recheck for diagnostic trouble code.....3574
DTC B1404: Driver' air bag module (1st squib) activating circuit short-circuited DTC B1405: Driver' air bag module (1st squib).....3575
DIAGNOSIS....3577
STEP 1. Using scan tool MB991958, diagnose the CAN bus line.....3577
STEP 2. Recheck for diagnostic trouble code.....3577
DTC B1406: Malfunction of front impact sensor (RH)....3577
DIAGNOSIS....3578
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3578
STEP 2. Check the front impact sensor (RH).....3578
STEP 3. Recheck for diagnostic trouble code.....3578
DTC B1407: Front Impact Sensor (RH) Voltage Error....3578
DIAGNOSIS....3579
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3579
STEP 2. Recheck for diagnostic trouble code.....3579
STEP 3. Check of short to power supply, short to ground, and open circuit in FRH-, FRH+ line between SRS-ECU connector and front impact sensor (RH) connector.....3579
STEP 4. Check the front impact sensor (RH).....3580
STEP 5. Recheck for diagnostic trouble code.....3580
DTC B1408: Front Impact Sensor (RH) Communication Error DTC B1409: Front Impact Sensor (RH) Communication Impossible....3580
DIAGNOSIS....3581
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3581
STEP 2. Recheck for diagnostic trouble code.....3581
STEP 3. Check the front impact sensor (RH).....3581
STEP 4. Check of short to power supply, short to ground, and open circuit in FRH-, FRH+ line between SRS-ECU connector and front impact sensor (RH) connector.....3581
STEP 5. Recheck for diagnostic trouble code.....3582
DTC B1410: Passenger' (front) air bag module (1st squib) system (short circuit between squib circuit terminals) DTC B1490: Passenger' (front) air bag module (2nd squib) system (short circuit between squib circuit terminals)....3582
DIAGNOSIS....3583
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3583
STEP 2. Recheck for diagnostic trouble code.....3583
STEP 3. Connector check: passenger' (front) air bag module, SRS-ECU.....3584
STEP 4. Diagnosis check by dummy resistor connection.....3585
STEP 5. Resistance measurement at the SRS-ECU connector.....3586
STEP 6. Check for diagnostic trouble code.....3587
DTC B1411: Passenger' (front) air bag module (1st squib) system (open circuit of squib circuit) DTC B1491: Passenger' (front) air bag module (2nd squib) system (squib circuit open)....3587
DIAGNOSIS....3587
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3587
STEP 2. Recheck for diagnostic trouble code.....3588
STEP 3. Diagnosis check by dummy resistor connection.....3588
STEP 4. Resistance measurement at the SRS-ECU connector and the passenger' (front) air bag module connector.....3589
STEP 5. Recheck for diagnostic trouble code.....3590
DTC B1412: Passenger' (front) air bag module (1st squib) system (shorted to squib circuit ground) DTC B1492: Passenger' (front) air bag module (2nd squib) system (shorted to squib circuit ground)....3590
DIAGNOSIS....3591
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3591
STEP 2. Recheck for diagnostic trouble code.....3591
STEP 3. Diagnosis check by dummy resistor connection.....3592
STEP 4. Resistance measurement at the SRS-ECU connector.....3593
STEP 5. Recheck for diagnostic trouble code.....3594
DTC B1413: Passenger' (front) air bag module (1st squib) system (shorted to squib circuit power supply) DTC B1493: Passenger' (front) air bag module (2nd squib) system (shorted to squib circuit power supply....3594
DIAGNOSIS....3594
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3594
STEP 2. Recheck for diagnostic trouble code.....3595
STEP 3. Diagnosis check by dummy resistor connection.....3595
STEP 4. Voltage measurement at the SRS-ECU connector.....3596
STEP 5. Recheck for diagnostic trouble code.....3597
DTC B1416: Malfunction of front impact sensor (LH)....3597
DIAGNOSIS....3597
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3597
STEP 2. Check the front impact sensor (LH).....3598
STEP 3. Recheck for diagnostic trouble code.....3598
DTC B1417: Front impact sensor (LH) voltage error....3598
DIAGNOSIS....3599
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3599
STEP 2. Recheck for diagnostic trouble code.....3599
STEP 3. Check of short to power supply, short to ground, and open circuit in FLH-, FLH+ line between SRS-ECU connector and front impact sensor (LH) connector.....3599
STEP 4. Check the front impact sensor (LH).....3599
STEP 5. Recheck for diagnostic trouble code.....3600
DTC B1418: Front impact sensor (LH) communication error DTC B1419: Front impact sensor (LH) communication impossible....3600
DIAGNOSIS....3600
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3600
STEP 2. Recheck for diagnostic trouble code.....3601
STEP 3. Check the front impact sensor (LH).....3601
STEP 4. Check of short to power supply, short to ground, and open circuit in FLH-, FLH+ line between SRS-ECU connector and front impact sensor (LH) connector.....3601
STEP 5. Recheck for diagnostic trouble code.....3601
DTC B1420: Side-airbag module (RH) (squib) system (short circuit between squib terminals)....3602
DIAGNOSIS....3602
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3602
STEP 2. Recheck for diagnostic trouble code.....3602
STEP 3. Connector check: SRS-ECU, side-airbag module (RH).....3603
STEP 4. Diagnosis check by dummy resistor connection.....3604
STEP 5. Resistance measurement at the SRS-ECU connector.....3605
STEP 6. Recheck for diagnostic trouble code.....3605
DTC B1421: Side-airbag module (RH) (squib) system (open circuit of squib circuit)....3606
DIAGNOSIS....3606
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3606
STEP 2. Recheck for diagnostic trouble code.....3606
STEP 3. Check the side-airbag module (RH).....3607
STEP 4. Resistance measurement at the SRS-ECU connector and the side-airbag module (RH) connector.....3608
STEP 5. Recheck for diagnostic trouble code.....3609
DTC B1422: Side-airbag module (RH) (squib) system (shorted to squib circuit ground)....3609
DIAGNOSIS....3609
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3609
STEP 2. Recheck for diagnostic trouble code.....3610
STEP 3. Check the side-airbag module (RH).....3610
STEP 4. Resistance measurement at the SRS-ECU connector.....3611
STEP 5. Recheck for diagnostic trouble code.....3611
DTC B1423: Side-airbag module (RH) (squib) system (shorted to squib circuit power supply)....3612
DIAGNOSIS....3612
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3612
STEP 2. Recheck for diagnostic trouble code.....3612
STEP 3. Check the side-airbag module (RH).....3613
STEP 4. Voltage measurement at the SRS-ECU connector.....3614
STEP 5. Recheck for diagnostic trouble code.....3615
DTC B1426: Malfunction of Side Impact Sensor (RH) DTC B1436: Malfunction of Side Impact Sensor (LH)....3615
DIAGNOSIS....3615
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3615
STEP 2. Side impact sensor check.....3616
STEP 3. Recheck for diagnostic trouble code.....3616
DTC B1427: Side impact sensor (RH) voltage error....3616
DIAGNOSIS....3617
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3617
STEP 2. Recheck for diagnostic trouble code.....3617
STEP 3. Check of short to power supply, short to ground, and open circuit in SSR-, SSR+ line in between SRS-ECU connector and side impact sensor (RH) connector.....3617
STEP 4. Check the side impact sensor (RH).....3617
STEP 5. Recheck for diagnostic trouble code.....3618
DTC B1428: Side impact sensor (RH) communication error DTC B1429: Side impact sensor (RH) communication impossible....3618
DIAGNOSIS....3618
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3618
STEP 2. Recheck for diagnostic trouble code.....3619
STEP 3. Right side impact sensor check.....3619
STEP 4. Check of short to power supply, short to ground, and open circuit in SSR-, SSR+ line in between SRS-ECU connector and side impact sensor (RH) connector.....3619
STEP 5. Check whether the DTC is stored again.....3619
DTC B1430: Side-airbag module (LH) (squib) system (short circuit between squib terminals)....3620
DIAGNOSIS....3620
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3620
STEP 2. Recheck for diagnostic trouble code.....3621
STEP 3. Connector check: SRS-ECU, side-airbag module (LH).....3621
STEP 4. Diagnosis check by dummy resistor connection.....3622
STEP 5. Resistance measurement at the SRS-ECU connector.....3623
STEP 6. Recheck for diagnostic trouble code.....3623
DTC B1431: Side-airbag module (LH) (squib) system (open circuit of squib circuit)....3624
DIAGNOSIS....3624
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3624
STEP 2. Recheck for diagnostic trouble code.....3624
STEP 3. Diagnosis check by dummy resistor connection.....3625
STEP 4. Resistance measurement at the SRS-ECU connector and the side-airbag module (LH) connector.....3626
STEP 5. Recheck for diagnostic trouble code.....3627
DTC B1432: Side-airbag module (LH) (squib) system (shorted to squib circuit earth)....3627
DIAGNOSIS....3627
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3627
STEP 2. Recheck for diagnostic trouble code.....3628
STEP 3. Diagnosis check by dummy resistor connection.....3628
STEP 4. Resistance measurement at the SRS-ECU connector.....3629
STEP 5. Recheck for diagnostic trouble code.....3630
DTC B1433: Side-airbag module (LH) (squib) system (shorted to squib circuit power supply)....3630
DIAGNOSIS....3630
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3630
STEP 2. Recheck for diagnostic trouble code.....3631
STEP 3. Diagnosis check by dummy resistor connection.....3631
STEP 4. Voltage measurement at the SRS-ECU connector.....3632
STEP 5. Recheck for diagnostic trouble code.....3633
DTC B1437: Side impact sensor (LH) voltage error....3633
DIAGNOSIS....3633
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3633
STEP 2. Recheck for diagnostic trouble code.....3634
STEP 3. Check of short to power supply, short to ground, and open circuit in SSL+, SSL- line in between SRS-ECU connector and side impact sensor (LH) connector.....3634
STEP 4. Check the side impact sensor (LH).....3634
STEP 5. Check whether the DTC is reset.....3634
DTC B1438: Side impact sensor (LH) communication error DTC B1439: Side impact sensor (LH) communication impossible....3635
DIAGNOSIS....3635
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3635
STEP 2. Recheck for diagnostic trouble code.....3635
STEP 3. Check the side impact sensor (LH).....3636
STEP 4. Check of short to power supply, short to ground, and open circuit in SSL+, SSL- line in between SRS-ECU connector and side impact sensor (LH) connector.....3636
STEP 5. Check whether the DTC is reset.....3636
DTC B1440: Curtain air bag module (RH) (squib) system (short circuit between squib circuit terminals)....3636
DIAGNOSIS....3637
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3637
STEP 2. Recheck for diagnostic trouble code.....3637
STEP 3. Connector check: SRS-ECU, curtain air bag module (RH).....3638
STEP 4. Diagnosis check by dummy resistor connection.....3638
STEP 5. Resistance measurement at the SRS-ECU connector.....3639
STEP 6. Recheck for diagnostic trouble code.....3639
DTC B1441: Curtain air bag module (RH) (squib) system (open circuit of squib circuit)....3640
DIAGNOSIS....3640
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3640
STEP 2. Recheck for diagnostic trouble code.....3640
STEP 3. Diagnosis check by dummy resistor connection.....3641
STEP 4. Resistance measurement at the SRS-ECU connector and the curtain air bag module (RH) connector.....3642
STEP 5. Recheck for diagnostic trouble code.....3643
DTC B1442: Curtain air bag module (RH) (squib) system (shorted to squib circuit ground)....3643
DIAGNOSIS....3644
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3644
STEP 2. Recheck for diagnostic trouble code.....3644
STEP 3. Diagnosis check by dummy resistor connection....3645
STEP 4. Resistance measurement at the SRS-ECU connector.....3646
STEP 5. Recheck for diagnostic trouble code.....3646
DTC B1443: Curtain air bag module (RH) (squib) system (shorted to squib circuit power supply)....3647
DIAGNOSIS....3647
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3647
STEP 2. Recheck for diagnostic trouble code.....3647
STEP 3. Diagnosis check by dummy resistor connection....3648
STEP 4. Voltage measurement at the SRS-ECU connector.....3649
STEP 5. Recheck for diagnostic trouble code.....3649
DTC B1450: Curtain air bag module (LH) (squib) system (short circuit between squib circuit terminals)....3650
DIAGNOSIS....3650
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3650
STEP 2. Recheck for diagnostic trouble code.....3651
STEP 3. Connector check: SRS-ECU, curtain air bag module (LH) connector.....3651
STEP 4. Diagnosis check by dummy resistor connection.....3652
STEP 5. Resistance measurement at the SRS-ECU connector.....3653
STEP 6. Recheck for diagnostic trouble code.....3653
DTC B1451: Curtain air bag module (LH) (squib) system (open circuit of squib circuit)....3654
DIAGNOSIS....3654
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3654
STEP 2. Recheck for diagnostic trouble code.....3654
STEP 3. Diagnosis check by dummy resistor connection.....3655
STEP 4. Resistance measurement at the SRS-ECU connector and the curtain air bag module (LH) connector.....3656
STEP 5. Recheck for diagnostic trouble code.....3657
DTC B1452: Curtain air bag module (LH) (squib) system (shorted to squib circuit ground)....3657
DIAGNOSIS....3658
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3658
STEP 2. Recheck for diagnostic trouble code.....3658
STEP 3. Diagnosis check by dummy resistor connection....3659
STEP 4. Resistance measurement at the SRS-ECU connector.....3660
STEP 5. Recheck for diagnostic trouble code.....3660
DTC B1453: Curtain air bag module (LH) (squib) system (shorted to squib circuit power supply)....3661
DIAGNOSIS....3661
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3661
STEP 2. Recheck for diagnostic trouble code.....3661
STEP 3. Diagnosis check by dummy resistor connection....3662
STEP 4. Voltage measurement at the SRS-ECU connector.....3663
STEP 5. Recheck for diagnostic trouble code.....3663
DTC B1476: IG1 power supply open circuit (Fuse No. 15 circuit) DTC B1477: IG1 power supply open circuit (Fuse No. 21 circuit)....3664
DIAGNOSIS....3664
STEP 1. Power supply fuse check.....3664
STEP 2. Fuse open circuit check....3664
STEP 3. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3665
STEP 4. Using scan tool (M.U.T.-III), check data list.....3665
STEP 5. Recheck for diagnostic trouble code.....3665
STEP 6. Resistance measurement at the SRS-ECU connector.....3666
STEP 7. Voltage measurement at the SRS-ECU connector (IG1A, IG1B line).....3666
STEP 8. Resistance measurement at the SRS-ECU connector.....3667
STEP 9. Recheck for diagnostic trouble code.....3667
DTC B1488: Passenger' air bag OFF indicator light (short circuited)....3667
DIAGNOSIS....3668
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3668
STEP 2. Recheck for diagnostic trouble code.....3668
STEP 3. Check the passenger’s air bag OFF indicator light.....3668
STEP 4. Resistance measurement at the SRS-ECU connector.....3669
STEP 5. Recheck for diagnostic trouble code.....3669
DTC B1489: Passenger’s air bag OFF indicator light (open circuit)....3669
DIAGNOSIS....3670
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3670
STEP 2. Recheck for diagnostic trouble code.....3670
STEP 3. Check the passenger’s air bag OFF indicator light.....3670
STEP 4. Resistance measurement at the SRS-ECU connector and the passenger’s air bag OFF indicator light connector.....3671
STEP 5. Measure the voltage at the passenger’s air bag OFF indicator light connector.....3671
STEP 6. Recheck for diagnostic trouble code.....3671
DTC B1499: Air bag deployment determined by SRS-ECU....3672
DIAGNOSIS....3672
DTC B1509: Incorrect installation of SRS-ECU....3672
DIAGNOSIS....3672
DTC B1530: Seat Belt Switch (Passenger’s side) Malfunction DTC B1537: Seat Belt Switch (Passenger’s side) Circuit Open DTC B15....3672
DIAGNOSIS....3673
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3673
STEP 2. Recheck for diagnostic trouble code.....3673
STEP 3. Seat belt switch (passenger’s side) check.....3673
STEP 4. Check the harness short circuit between seat belt switch (passenger’s side) connector and the SRS-ECU connector.....3674
STEP 5. Resistance measurement at the SRS-ECU connector and the seat belt switch (passenger’s side) connector.....3675
STEP 6. Recheck for diagnostic trouble code.....3675
DTC B1558: OCM (Occupant Classification-ECU) DTC Present....3676
DIAGNOSIS....3676
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3676
STEP 2. Recheck for diagnostic trouble code.....3676
STEP 3. Recheck for diagnostic trouble code.....3676
STEP 4. Recheck for diagnostic trouble code.....3677
DTC B1603: Seat belt pre-tensioner (driver’s side) (squib) system (short circuit between squib circuit terminals)....3677
DIAGNOSIS....3678
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3678
STEP 2. Recheck for diagnostic trouble code.....3678
STEP 3. Connector check: SRS-ECU connector, seat belt pre-tensioner (driver’s side) connector.....3679
STEP 4. Diagnosis check by dummy resistor connection.....3679
STEP 5. Resistance check at the SRS-ECU connector (PTD+, PTD- line).....3680
STEP 6. Recheck for diagnostic trouble code.....3681
DTC B1604: Seat belt pre-tensioner (driver’s side) (squib) system (open circuit of squib circuit)....3681
DIAGNOSIS....3681
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3681
STEP 2. Recheck for diagnostic trouble code.....3682
STEP 3. Diagnosis check by dummy resistor connection.....3682
STEP 4. Resistance measurement at the SRS-ECU connector and the seat belt pre-tensioner (driver’s side) connector.....3683
STEP 5. Recheck for diagnostic trouble code.....3684
DTC B1605: Seat belt pre-tensioner (driver’s side) (squib) system (shorted to squib circuit ground)....3684
DIAGNOSIS....3684
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3684
STEP 2. Recheck for diagnostic trouble code.....3685
STEP 3. Diagnosis check by dummy resistor connection.....3685
STEP 4. Resistance measurement at the SRS-ECU connector.....3686
STEP 5. Recheck for diagnostic trouble code.....3687
DTC B1606: Seat belt pre-tensioner (driver’s side) (squib) system (shorted to squib circuit power supply)....3687
DIAGNOSIS....3687
STEP 1. Using scan tool MB991958, diagnose the CAN bus line.....3687
STEP 2. Recheck for diagnostic trouble code.....3688
STEP 3. Diagnosis check by dummy resistor connection.....3688
STEP 4. Voltage measurement at the SRS-ECU connector.....3689
STEP 5. Recheck for diagnostic trouble code.....3690
DTC B1609: Seat belt pre-tensioner (passenger’s side) (squib) system (short circuit between squib circuit terminals)....3690
DIAGNOSIS....3690
STEP 1. Using scan tool MB991958, diagnose the CAN bus line.....3690
STEP 2. Recheck for diagnostic trouble code.....3691
STEP 3. Connector check: SRS-ECU, seat belt pre-tensioner (passenger' side).....3691
STEP 4. Diagnosis check by dummy resistor connection.....3692
STEP 5. Resistance check at the SRS-ECU connector.....3693
STEP 6. Recheck for diagnostic trouble code.....3693
DTC B1610: Seat belt pre-tensioner (passenger’s side) (squib) system (open circuit of squib circuit)....3694
DIAGNOSIS....3694
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3694
STEP 2. Recheck for diagnostic trouble code.....3694
STEP 3. Diagnosis check by dummy resistor connection.....3695
STEP 4. Resistance measurement at the SRS-ECU connector and the seat belt pre-tensioner (passenger' side) connector.....3696
STEP 5. Recheck for diagnostic trouble code.....3697
DTC B1611: Seat belt pre-tensioner (passenger’s side) (squib) system (shorted to squib circuit ground)....3697
DIAGNOSIS....3698
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3698
STEP 2. Recheck for diagnostic trouble code.....3698
STEP 3. Diagnosis check by dummy resistor connection.....3699
STEP 4. Resistance measurement at the SRS-ECU connector.....3700
STEP 5. Recheck for diagnostic trouble code.....3700
DTC B1612: Seat belt pre-tensioner (passenger’s side) (squib) system (shorted to squib circuit power supply)....3701
DIAGNOSIS....3701
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3701
STEP 2. Recheck for diagnostic trouble code.....3701
STEP 3. Diagnosis check by dummy resistor connection.....3702
STEP 4. Voltage measurement at the SRS-ECU connector.....3703
STEP 5. Recheck for diagnostic trouble code.....3704
DTC B1631: Driver' knee air bag module (squib) system (short circuit between squib circuit terminals)....3704
DIAGNOSIS....3705
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3705
STEP 2. Recheck for diagnostic trouble code.....3705
STEP 3. Connector check: SRS-ECU, knee air bag module.....3706
STEP 4. Diagnosis check by dummy resistor connection.....3706
STEP 5. Resistance check at the SRS-ECU connector.....3707
STEP 6. Recheck for diagnostic trouble code.....3707
DTC B1632: Driver' knee air bag module (squib) system (open circuit of squib circuit)....3708
DIAGNOSIS....3708
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3708
STEP 2. Recheck for diagnostic trouble code.....3708
STEP 3. Diagnosis check by dummy resistor connection.....3709
STEP 4. Resistance measurement at the SRS-ECU connector and the knee air bag module connector.....3710
STEP 5. Recheck for diagnostic trouble code.....3711
DTC B1633: Driver' knee air bag module (squib) system (shorted to squib circuit ground)....3711
DIAGNOSIS....3712
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3712
STEP 2. Recheck for diagnostic trouble code.....3712
STEP 3. Diagnosis check by dummy resistor connection.....3713
STEP 4. Resistance measurement at the SRS-ECU connector.....3714
STEP 5. Recheck for diagnostic trouble code.....3714
DTC B1634: Driver' knee air bag module (squib) system (shorted to squib circuit power supply)....3715
DIAGNOSIS....3715
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3715
STEP 2. Recheck for diagnostic trouble code.....3715
STEP 3. Diagnosis check by dummy resistor connection.....3716
STEP 4. Voltage measurement at the SRS-ECU connector.....3717
STEP 5. Recheck for diagnostic trouble code.....3718
DTC B1646: Coding data mismatch....3718
DTC B1699: SRS-ECU collective deployment....3718
DTC U0154: Occupant Classification-ECU CAN timeout....3718
DIAGNOSIS....3719
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line....3719
STEP 2. Using scan tool (M.U.T.-III), read the occupant classification-ECU diagnostic trouble code.....3719
STEP 3. Using scan tool (M.U.T.-III), read diagnostic trouble code No. U0154 for other system.....3719
STEP 4. Recheck for diagnostic trouble code.....3720
DTC U1100: Engine CAN timeout....3720
DIAGNOSIS....3720
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line....3720
STEP 2. Using scan tool (M.U.T.-III), read the other systems diagnostic trouble code.....3721
STEP 3. Using scan tool (M.U.T.-III), read the other systems diagnostic trouble code.....3721
STEP 4. Check whether the diagnostic trouble code is stored again.....3721
STEP 5. Check whether the diagnostic trouble code is stored again.....3721
STEP 6. Recheck for diagnostic trouble code.....3722
DTC U1102: ASC/TCL/ABS timeout/Not equipped....3722
DIAGNOSIS....3722
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3722
STEP 2. Using scan tool (M.U.T.-III), read the ASC-ECU diagnostic trouble code.....3723
STEP 3. Using scan tool (M.U.T.-III), read the ETACS diagnostic trouble code.....3723
STEP 4. Recheck for diagnostic trouble code.....3723
STEP 5. Recheck for diagnostic trouble code.....3723
STEP 6. Recheck for diagnostic trouble code.....3724
DTC U1104: SAS CAN timeout/Not equipped....3724
DIAGNOSIS....3724
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3724
STEP 2. Using scan tool (M.U.T.-III), read the EPS-ECU diagnostic trouble code....3724
STEP 3. Using scan tool (M.U.T.-III), read diagnostic trouble code No. U1104 for other system.....3725
STEP 4. Recheck for diagnostic trouble code.....3725
DTC U1108: Combination Meter CAN timeout....3725
DIAGNOSIS....3726
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3726
STEP 2. Using scan tool (M.U.T.-III), read the combination meter diagnostic trouble code....3726
STEP 3. Using scan tool (M.U.T.-III), read diagnostic trouble code No. U1108 for other system.....3726
STEP 4. Recheck for diagnostic trouble code.....3726
DTC U1109: ETACS CAN timeout....3727
DIAGNOSIS....3727
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line....3727
STEP 2. Using scan tool (M.U.T.-III), read the ETACS-ECU diagnostic trouble code....3727
STEP 3. Using scan tool (M.U.T.-III), read diagnostic trouble code No. U1109 for other system.....3727
STEP 4. Recheck for diagnostic trouble code.....3728
DTC U1190: No receive fault detect signal....3728
DIAGNOSIS....3728
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line....3728
STEP 2. Recheck for diagnostic trouble code.....3729
STEP 3. Recheck for diagnostic trouble code.....3729
STEP 4. Recheck for diagnostic trouble code.....3729
DTC U1195: Coding not completed....3729
DIAGNOSIS....3729
DTC U1199: VIN code not programmed....3730
DIAGNOSIS....3730
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3730
STEP 2. Register the VIN and recheck the diagnostic trouble code.....3730
DTC U119A: VIN code mismatch....3731
DIAGNOSIS....3731
STEP 1. Check the VIN registered in the engine control module and the VIN of the vehicle.....3731
STEP 2. Recheck for diagnostic trouble code.....3731
STEP 3. Recheck for diagnostic trouble code.....3731
DIAGNOSTIC TROUBLE CODE PROCEDURES <OCCUPANT CLASSIFICATION-ECU>....3732
DTC B1690: Electromagnetic Interference....3732
DIAGNOSIS....3733
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3733
STEP 2. Check whether any electronic appliance has been put on the front passenger' seat.....3733
STEP 3. Recheck for diagnostic trouble code.....3733
DTC B1691: Occupant Sensing Antenna DTC B1693: Occupant Sensing Antenna Open DTC B1694: Occupant Sensing ANT.SHT to GND DTC B1695: Occupant Sensing ANT.SHT to BAT....3734
DIAGNOSIS....3734
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3734
STEP 2. Check whether the front passenger' seat is damped with liquid or steam.....3734
STEP 3. Recheck for diagnostic trouble code.....3735
STEP 4. Check open circuit in GND line between occupant classification-ECU connector and body ground.....3735
STEP 5. Check of short to power supply, short to ground, and open circuit in SENSE, GUARD line between occupant classification-ECU connector and occupant classification sensor connector.....3735
STEP 6. Recheck for diagnostic trouble code.....3735
DTC B1CB2: Occupant Classification-ECU Parameter Table Incompatible....3736
DIAGNOSIS....3736
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3736
STEP 2. Recheck for diagnostic trouble code.....3736
DTC B210D: Battery Voltage Low DTC B210E: Battery Voltage High....3737
DIAGNOSIS....3737
STEP 1. Measure the voltage at the occupant classification-ECU connector.....3737
STEP 2. Power supply fuse No.21 check.....3737
STEP 3. Check of short to power supply, short to ground, and open circuit in BTT line between junction block connector and the occupant classification-ECU connector.....3737
STEP 4. Battery check.....3738
STEP 5. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3738
STEP 6. Recheck for diagnostic trouble code.....3738
STEP 7. Recheck for diagnostic trouble code.....3738
DTC B2212 OCM internal error....3739
DIAGNOSIS....3739
Recheck for diagnostic trouble code.....3739
DTC U1109: ETACS CAN Timeout....3739
DIAGNOSIS....3740
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line....3740
STEP 2. Using scan tool (M.U.T.-III), read the ETACS-ECU diagnostic trouble code....3740
STEP 3. Using scan tool (M.U.T.-III), read diagnostic trouble code No. U1109 for other system.....3740
STEP 4. Recheck for diagnostic trouble code.....3740
DTC U1190: No receive fault detect signal....3741
DIAGNOSIS....3741
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line....3741
STEP 2. Recheck for diagnostic trouble code.....3741
STEP 3. Recheck for diagnostic trouble code.....3742
STEP 4. Recheck for diagnostic trouble code.....3742
DTC U15A2 Vehicle speed information lost....3742
DIAGNOSIS....3743
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3743
STEP 2. Using scan tool (M.U.T.-III), check for any ASC diagnostic trouble code.....3743
STEP 3. Using scan tool (M.U.T.-III), read the KOS-ECU diagnostic trouble code.....3743
STEP 4. Recheck for diagnostic trouble code.....3743
STEP 5. Recheck for diagnostic trouble code.....3744
DTC U15A3 Odometer information lost....3744
DIAGNOSIS....3745
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3745
STEP 2. Using scan tool (M.U.T.-III), read the combination meter diagnostic trouble code....3745
STEP 3. Using scan tool (M.U.T.-III), read diagnostic trouble code No. U1108 for other system.....3745
STEP 4. Recheck for diagnostic trouble code.....3745
DTC U15A4 VIN information lost....3746
DIAGNOSIS....3746
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3746
STEP 2. Using scan tool (M.U.T.-III), read the engine control module diagnostic trouble code....3746
STEP 3. Check whether the diagnostic trouble code is stored again.....3747
STEP 4. Check whether the diagnostic trouble code is stored again.....3747
STEP 5. Check whether the diagnostic trouble code is stored again.....3747
SYMPTOM PROCEDURES....3748
Inspection Procedure 1: Communication between scan tool and SRS-ECU cannot be established.....3748
DIAGNOSIS....3748
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3748
Inspection Procedure 2: Power supply circuit system....3748
DIAGNOSIS....3749
STEP 1. Fuse Nos. 15, 21 check.....3749
STEP 2. Fuse open circuit check....3749
STEP 3. Check of open circuit in GND1 line between SRS-ECU and body ground.....3749
STEP 4. Check of short to power supply, short to ground, and open circuit in IG1A, IG1B line between SRS-ECU and junction block.....3749
STEP 5. Trouble symptom check.....3750
Inspection Procedure 3: SRS warning light does not illuminate.....3750
DIAGNOSIS....3750
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3750
STEP 2. Using scan tool (M.U.T.-III), actuator test....3750
STEP 3. Using scan tool (M.U.T.-III), actuator test....3751
STEP 4. Check of short to power supply, short to ground, and open circuit in IG1 line between junction block connector and combination meter connector....3751
STEP 5. Recheck of the SRS warning light....3751
Inspection Procedure 4: The SRS warning light does not go out.....3751
DIAGNOSIS....3752
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....3752
STEP 2. Recheck of the SRS warning light....3752
STEP 3. Using scan tool (M.U.T.-III), actuator test.....3752
STEP 4. Check for diagnostic trouble code.....3752
STEP 5. Recheck of the SRS warning light....3752
FAIL-SAFE FUNCTION REFERENCE TABLE....3753
POST-COLLISION DIAGNOSIS....3753
SRS-ECU MEMORY CHECK....3753
REPAIR PROCEDURE....3755
INDIVIDUAL COMPONENT SERVICE....3759
WARNING/CAUTION LABELS....3760
FRONT IMPACT SENSORS....3761
REMOVAL SERVICE POINT....3762
INSTALLATION SERVICE POINTS....3762
INSPECTION....3763
SRS CONTROL UNIT (SRS-ECU)....3764
REMOVAL SERVICE POINTS....3765
INSTALLATION SERVICE POINTS....3765
INSPECTION....3766
DRIVER' AIR BAG MODULE AND CLOCK SPRING....3767
REMOVAL SERVICE POINTS....3768
INSTALLATION SERVICE POINTS....3771
INSPECTION....3773
PASSENGER' (FRONT) AIR BAG MODULE....3775
REMOVAL SERVICE POINTS....3776
INSTALLATION SERVICE POINTS....3776
SIDE-AIRBAG MODULE(S)....3778
REMOVAL SERVICE POINT....3779
INSTALLATION SERVICE POINTS....3779
INSPECTION....3781
FRONT SEATBACK ASSEMBLY WITH SIDE-AIRBAG MODULE CHECK....3781
CURTAIN AIR BAG MODULE(S)....3782
REMOVAL SERVICE POINTS....3783
INSTALLATION SERVICE POINTS....3784
INSPECTION....3785
CURTAIN AIR BAG MODULE CHECK....3785
KNEE AIR BAG MODULE....3786
REMOVAL SERVICE POINTS....3787
INSTALLATION SERVICE POINTS....3788
INSPECTION....3789
KNEE AIR BAG MODULE CHECK....3789
SIDE IMPACT SENSOR....3790
REMOVAL SERVICE POINTS....3791
INSTALLATION SERVICE POINTS....3791
INSPECTION....3792
SEAT BELTS WITH PRE-TENSIONER....3793
REMOVAL SERVICE POINTS....3795
INSTALLATION SERVICE POINTS....3795
INSPECTION....3796
SEAT BELT WITH PRE-TENSIONER CHECK....3796
OCCUPANT CLASSIFICATION-ECU....3797
REMOVAL SERVICE POINT....3798
INSTALLATION SERVICE POINTS....3798
INSPECTION....3798
OCCUPANT CLASSIFICATION SENSOR....3799
REMOVAL SERVICE POINT....3800
INSTALLATION SERVICE POINTS....3800
INSPECTION....3800
PASSENGER' AIR BAG ON/OFF INDICATOR LIGHT....3801
REMOVAL SERVICE POINT....3802
INSTALLATION SERVICE POINTS....3802
INSPECTION....3803
AIR BAG MODULE DISPOSAL PROCEDURES....3803
DISPOSAL OF UNDEPLOYED AIR BAG MODULES....3804
DISCARD OF DEPLOYED AIR BAG MODULE....3819
SEAT BELT PRE-TENSIONER DISPOSAL PROCEDURES....3820
UNDEPLOYED SEAT BELT WITH PRE-TENSIONER DISPOSAL....3820
DISCARD OF DEPLOYED SEAT BELT WITH PRE-TENSIONER....3823
GR00004000-52....3824
INTERIOR AND SUPPLEMENTAL RESTRAINT SYSTEM(SRS)....3824
GR00004100-00....3826
GENERAL <BODY AND CHASSIS>....3826
HOW TO USE THIS MANUAL....3828
MAINTENANCE, REPAIR AND SERVICING EXPLANATIONS....3828
DEFINITION OF TERMS....3828
TIGHTENING TORQUE INDICATION....3828
SPECIAL TOOL NOTE....3828
ABBREVIATIONS....3828
TROUBLESHOOTING GUIDELINES....3831
VERIFY THE COMPLAINT....3831
DETERMINE POSSIBLE CAUSES....3831
FIND THE PROBLEM....3831
REPAIR THE PROBLEM....3831
VERIFY THE REPAIR....3831
HOW TO USE TROUBLESHOOTING/ INSPECTION SERVICE POINTS....3831
1. STANDARD FLOW OF DIAGNOSTIC TROUBLESHOOTING....3831
2. SYSTEM OPERATION AND SYMPTOM VERIFICATION TESTS....3831
3. DIAGNOSTIC FUNCTION....3831
4. DIAGNOSTIC TROUBLE CODE CHART....3832
5. SYMPTOM CHART....3832
6. DIAGNOSTIC TROUBLE CODE PROCEDURES....3832
7. SYMPTOM PROCEDURES....3832
8. SERVICE DATA REFERENCE TABLE....3832
9. CHECK AT ECU TERMINALS....3832
10. INSPECTION PROCEDURES USING AN OSCILLOSCOPE....3832
HARNESS INSPECTION....3834
MEASURES TO TAKE AFTER REPLACING THE ECU....3835
CONNECTOR MEASUREMENT SERVICE POINTS....3835
IF INSPECTING WITH THE CONNECTOR CONNECTED <WATERPROOF CONNECTORS>....3835
IF INSPECTING WITH THE CONNECTOR CONNECTED <ORDINARY (NON-WATERPROOF) CONNECTORS>....3835
IF INSPECTING WITH THE CONNECTOR DISCONNECTED....3835
CONNECTOR INSPECTION SERVICE POINTS....3837
VISUAL INSPECTION....3837
HOW TO COPE WITH INTERMITTENT MALFUNCTIONS....3838
HOW TO TREAT PAST TROUBLE....3839
INSPECTION SERVICE POINTS FOR A BLOWN FUSE....3840
VEHICLE IDENTIFICATION....3840
VEHICLE IDENTIFICATION NUMBER PLATE....3840
VEHICLES IDENTIFICATION NUMBER LOCATION....3840
VEHICLE IDENTIFICATION NUMBER LIST....3841
CHASSIS NUMBER....3842
VEHICLE IDENTIFICATION CODE PLATE....3843
CERTIFICATION LABEL....3843
TIRE AND LOADING INFORMATION PLACARD....3844
ENGINE MODEL STAMPING....3844
GENERAL DATA AND SPECIFICATIONS....3845
PRECAUTIONS BEFORE SERVICE....3847
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)....3847
SCAN TOOL [MULTI USE TESTER (M.U.T.-III) SUB ASSEMBLY]....3848
SERVICING ELECTRICAL SYSTEM....3849
HOW TO SHIFT LOCK FORCED RELEASE <CVT>....3850
HOW TO PERFORM VIN WRITING FOR ENGINE CONTROL MODULE, KOS&OSS-ECU AND ETACS-ECU....3851
WHEN ECM IS REPLACED....3852
WHEN KOS&OSS-ECU, ESL ECU IS REPLACED....3854
WHEN ETACS-ECU IS REPLACED....3856
CODING LIST....3858
VARIANT CODING....3858
OPTION CODING....3865
INITIALIZATION PROCEDURE FOR LEARNING VALUE IN MFI ENGINE....3866
ENGINE IDLING LEARNING PROCEDURE....3866
PURPOSE....3866
LEARNING PROCEDURE....3867
INITIALIZATION PROCEDURE FOR THROTTLE ACTUATOR CONTROL MOTOR....3867
TIMING CHAIN LEARNED VALUE RESET....3867
PRE-INSPECTION CONDITION....3868
ENGINE OILS....3868
HEALTH WARNING....3868
RECOMMENDED PRECAUTIONS....3869
FORM-IN-PLACE GASKET (FIPG)....3869
BOLTS AND NUTS WITH STABILIZER FOR COEFFICIENT OF FRICTION....3871
APPLICATION OF ANTI-CORROSION AGENTS AND UNDERCOATS....3871
VEHICLE WASHING....3871
TOWING AND HOISTING....3872
WRECKER TOWING RECOMMENDATION....3872
LIFTING, JACKING SUPPORT LOCATION....3874
LUBRICATION AND MAINTENANCE....3876
MAINTENANCE SCHEDULES....3876
SEVERE SERVICE....3876
ENGINE OIL....3877
LUBRICANTS AND GREASES....3877
FUEL USAGE STATEMENT....3877
MATERIALS ADDED TO FUEL....3878
RECOMMENDED LUBRICANTS AND LUBRICANT CAPACITIES TABLE....3878
LUBRICANT SELECTION....3879
SCHEDULED MAINTENANCE TABLE....3880
MAINTENANCE SERVICE....3889
1. FUEL SYSTEM (TANK, PIPE LINE AND CONNECTION, AND FUEL TANK FILLER TUBE CAP)....3889
CHECK FOR LEAKS....3889
2. FUEL HOSES....3889
CHECK CONDITION....3889
3. AIR CLEANER ELEMENT....3889
REPLACE....3889
4. EVAPORATIVE EMISSION CONTROL SYSTEM (EXCEPT EVAPORATIVE EMISSION CANISTER)....3889
CHECK FOR LEAKS AND CLOGGING....3889
5. SPARK PLUGS (IRIDIUM-TIPPED TYPE)....3890
REPLACE....3890
6. INTAKE AND EXHAUST VALVE CLEARANCE....3890
INSPECT AND ADJUSTMENT....3890
7. DRIVE BELTS (FOR THE GENERATOR AND POWER STEERING OIL PUMP)....3893
DRIVE BELT CONDITION....3893
DRIVE BELT TENSION CHECK AND ADJUSTMENT....3893
8. EXHAUST SYSTEM (CONNECTION PORTION OF MUFFLER, MUFFLER PIPES AND CONVERTER HEAT SHIELDS)....3896
CHECK AND SERVICE....3896
9. ENGINE OIL....3896
10. ENGINE OIL FILTER....3897
11. TRANSAXLE OIL <M/T>....3899
CHECK OIL LEVEL AND CONDITION....3899
TRANSAXLE OIL REPLACEMENT....3899
12. TRANSMISSION FLUID <CVT>....3900
CHECK FLUID LEVEL AND CONDITION....3900
CHANGE....3901
13. ENGINE COOLANT....3902
CHANGE....3902
14. COOLANT HOSES (RADIATOR HOSE, HEATER HOSE)....3903
INSPECT....3903
15. DISK BRAKE PADS AND ROTORS....3903
INSPECT FOR WEAR....3903
16. REAR DRUM BRAKE LININGS AND REAR WHEEL CYLINDERS....3906
INSPECT FOR WEAR AND LEAKS....3906
17. BRAKE HOSES....3907
CHECK FOR DETERIORATION OR LEAKS....3907
18. BRAKE FLUID....3908
CHANGE....3908
19. BALL JOINT AND STEERING LINKAGE SEALS....3909
INSPECT FOR GREASE LEAKS AND DAMAGE....3909
20. DRIVE SHAFT BOOTS....3909
INSPECT FOR GREASE LEAKS AND DAMAGE....3909
21. SUSPENSION SYSTEM....3909
INSPECT FOR LOOSENESS AND DAMAGE....3909
22. TIRES....3909
ROTATE....3909
23. CLEAN AIR FILTER (AIR REFRESHER)....3910
REPLACE....3910
MAIN SEALANT AND ADHESIVE TABLE....3912
GR00004200-26....3916
FRONT AXLE....3916
SERVICE SPECIFICATIONS....3917
LUBRICANTS....3917
FRONT AXLE DIAGNOSIS....3917
SYMPTOM PROCEDURES....3918
INSPECTION PROCEDURE 1: Noise during Wheel Rotation....3918
DIAGNOSIS....3918
STEP 1. Check the wheel bearing end play.....3918
STEP 2. Check the driveshaft and inner shaft for bending.....3918
STEP 3. Check the center bearing for wear.....3918
STEP4. Check the driveshaft assembly for wear or damage.....3918
STEP 5. Retest the system.....3918
INSPECTION PROCEDURE 2: Noise Due to Excessive Play of Wheel in Turning Direction....3919
DIAGNOSIS....3919
STEP 1. Check for play in the inner shaft and side gear serration, the driveshaft and side gear serration, or the driveshaft and front hub serration.....3919
STEP 2. Retest the system.....3919
SPECIAL TOOLS....3919
ON-VEHICLE SERVICE....3922
WHEEL BEARING END PLAY CHECK....3922
HUB BOLT REPLACEMENT....3922
FRONT AXLE HUB ASSEMBLY....3923
REMOVAL SERVICE POINTS....3924
INSTALLATION SERVICE POINT....3927
INSPECTION....3928
DISASSEMBLY SERVICE POINTS....3930
REASSEMBLY SERVICE POINTS....3932
INSPECTION....3934
DRIVESHAFT ASSEMBLY....3935
REMOVAL SERVICE POINTS....3937
INSTALLATION SERVICE POINTS....3940
DISASSEMBLY SERVICE POINTS....3943
ASSEMBLY SERVICE POINTS....3943
INSPECTION....3945
EBJ/VUJ BOOT REPLACEMENT....3945
GR00004300-27....3950
REAR AXLE....3950
SERVICE SPECIFICATIONS....3951
SEALANT....3951
REAR AXLE DIAGNOSIS....3951
SYMPTOM PROCEDURES....3951
INSPECTION PROCEDURE 1: Abnormal Noise....3951
DIAGNOSIS....3951
STEP 1. Check the rear hub assembly installation self-locking nut for looseness.....3951
STEP 2. Check the wheel bearing end play.....3952
STEP 3. Check the rear hub rotary-sliding resistance.....3952
STEP 4. Retest the systems.....3952
SPECIAL TOOLS....3952
ON-VEHICLE SERVICE....3953
WHEEL BEARING END PLAY CHECK....3953
WHEEL BEARING ROTARY-SLIDING RESISTANCE CHECK....3953
REAR AXLE HUB ASSEMBLY....3954
REMOVAL SERVICE POINTS....3955
INSTALLATION SERVICE POINT....3955
DISASSEMBLY SERVICE POINT....3956
ASSEMBLY SERVICE POINT....3957
GR00004400-33....3958
FRONT SUSPENSION....3958
FASTENER TIGHTENING SPECIFICATIONS....3959
SERVICE SPECIFICATIONS....3959
FRONT SUSPENSION DIAGNOSIS....3959
SYMPTOM PROCEDURES....3960
INSPECTION PROCEDURE 1: Steering Wheel is Heavy, Vibrates or Pulls to One Side....3960
STEP 1. Check the tires.....3960
STEP 2. Check the wheel alignment.....3960
STEP 3. Check the lower arm ball joint.....3960
STEP 4. Check the coil spring.....3960
STEP 5. Retest the system.....3960
INSPECTION PROCEDURE 2: Excessive Body Rolling....3960
STEP 1. Check for broken or deteriorated stabilizer bar.....3960
STEP 2. Check the strut assembly for damage.....3960
STEP 3. Retest the system.....3960
INSPECTION PROCEDURE 3: Poor Ride....3961
STEP 1. Check for improper tire inflation pressure.....3961
STEP 2. Check for broken or deteriorated coil spring(s).....3961
STEP 3. Check for strut assembly damage.....3961
STEP 4. Retest the system.....3961
INSPECTION PROCEDURE 4: Unequal Ride Height....3961
STEP 1. Check for broken or deteriorated coil spring(s).....3961
STEP 2. Retest the system.....3961
INSPECTION PROCEDURE 5: Noise....3961
STEP 1. Check for lack of lubrication.....3961
STEP 2. Check the tightened parts for looseness as well as the bushings for wear.....3961
STEP 3. Check for broken coil spring.....3961
STEP 4. Check for strut assembly damage.....3961
STEP 5. Retest the system.....3962
SPECIAL TOOLS....3962
ON-VEHICLE SERVICE....3963
FRONT WHEEL ALIGNMENT CHECK AND ADJUSTMENT....3963
LOWER ARM BALL JOINT PLAY CHECK....3964
LOWER ARM BALL JOINT DUST COVER CHECK....3965
STRUT ASSEMBLY....3965
INSTALLATION SERVICE POINT....3966
INSPECTION....3966
DISASSEMBLY SERVICE POINTS....3967
ASSEMBLY SERVICE POINT....3968
INSPECTION....3969
LOWER ARM....3970
REMOVAL SERVICE POINT....3971
INSPECTION....3971
LOWER ARM REAR BUSHING REPLACEMENT....3972
STABILIZER BAR....3974
REMOVAL SERVICE POINT....3976
INSTALLATION SERVICE POINTS....3976
INSPECTION....3978
GR00004500-34....3980
REAR SUSPENSION....3980
FASTENER TIGHTENING SPECIFICATIONS....3981
SERVICE SPECIFICATIONS....3981
REAR SUSPENSION DIAGNOSIS....3981
SYMPTOM PROCEDURES....3982
INSPECTION PROCEDURE 1: Squeaks or other Abnormal Noise....3982
STEP 1. Check for loose rear suspension installation bolts and nuts.....3982
STEP 2. Check the malfunction of shock absorbers (worn bushings).....3982
STEP 3. Check the torsion axle arm assembly for deformity or damage.....3982
STEP 4. Retest the system.....3982
INSPECTION PROCEDURE 2: Poor Ride....3982
STEP 1. Check the excessive tire inflation pressure.....3982
STEP 2. Check for malfunction of shock absorbers (weak or broken springs).....3982
STEP 3. Retest the system.....3982
INSPECTION PROCEDURE 3: Body Tilting....3982
STEP 1. Check for weak or deteriorated bushings.....3982
STEP 2. Check for weak or broken springs.....3982
STEP 3. Check the torsion axle arm assembly for deformity or damage.....3983
STEP 4. Retest the system.....3983
SPECIAL TOOLS....3983
ON-VEHICLE SERVICE....3983
REAR WHEEL ALIGNMENT CHECK AND ADJUSTMENT....3983
SHOCK ABSORBER AND COIL SPRING....3985
REMOVAL SERVICE POINT....3985
INSTALLATION SERVICE POINT....3986
TORSION AXLE ARM ASSEMBLY....3987
INSPECTION....3988
GR00004600-35A....3990
BASIC BRAKE....3990
SERVICE SPECIFICATIONS....3991
LUBRICANTS....3991
SEALANT....3992
BASIC BRAKE SYSTEM DIAGNOSIS....3992
SYMPTOM PROCEDURES....3992
INSPECTION PROCEDURE 1: Vehicle Pulls to One Side when Brakes are Applied....3992
STEP 1. Check for oil, water, etc., on the pad or lining contact surface of all brakes.....3992
STEP 2. Check the lining and brake drum contact.....3993
STEP 3. Check the adjuster function.....3993
STEP 4. Check the brake drum inside diameter.....3993
STEP 5. Check disc brake pistons for smooth operation.....3993
STEP 6. Check brake disc(s) for run out.....3993
STEP 7. Check brake discs for correct thickness.....3994
STEP 8. Retest the system.....3994
INSPECTION PROCEDURE 2: Insufficient Braking Power....3994
STEP 1. Check whether the brake fluid is low, is the correct fluid (CVT fluid, engine oil, etc.) or is contaminated (debris, sand, etc.).....3994
STEP 2. Check for spongy (not firm brakes).....3994
STEP 3. Check the lining and brake drum contact.....3995
STEP 4. Check the adjuster function.....3995
STEP 5. Check the brake booster function.....3995
STEP 6. Check for pinched or restricted brake tube or hose.....3995
STEP 7. Check for oil, water, etc., on the pad or lining contact surfaces of all brakes.....3995
STEP 8. Check the proportioning valve operation.....3995
STEP 9. Retest the system.....3996
INSPECTION PROCEDURE 3: Increased Pedal Stroke (Reduced Pedal-to-Floor Board Clearance)....3996
STEP 1. Check for spongy (not firm) brakes.....3996
STEP 2. Check the pad for wear.....3996
STEP 3. Check the vacuum hose and check valve for damage.....3996
STEP 4. Check for brake fluid leaks.....3996
STEP 5. Check the master cylinder assembly.....3996
STEP 6. Recheck symptom.....3996
INSPECTION PROCEDURE 4: Brake Drag....3997
STEP 1. Check the parking brake operating lever return.....3997
STEP 2. Check the brake shoe springs for breakage.....3997
STEP 3. Check the parking brake pull amount.....3997
STEP 4. Check port for clogging.....3997
STEP 5. Check disk brake pistons for sticking.....3997
STEP 6. Recheck symptom.....3998
INSPECTION PROCEDURE 5: Scraping or Grinding Noise when Brakes are Applied....3998
STEP 1. Check the front brakes, then rear brakes, for metal-to-metal condition.....3998
STEP 2. Check for interference between the caliper and wheel.....3998
STEP 3. Check for interference between the dust cover and brake disc.....3998
STEP 4. Check the brake drums or discs for cracks.....3998
STEP 5. Check for bent backing plate(s).....3999
STEP 6. Retest the system.....3999
INSPECTION PROCEDURE 6: Squealing, Groaning or Chattering Noise when Brakes are Applied....3999
STEP 1. Check the brake drums and lining or brake disc and pads for wear or cutting.....3999
STEP 2. Check the calipers for rust.....3999
STEP 3. Check the lining parts for damage.....3999
STEP 4. Check whether the lining is dirty or greasy.....3999
STEP 5. Check whether the shoe hold-down springs are weak or the shoe-hold-down pins and springs are loose or damaged.....3999
STEP 6. Adjust the brake pedal or brake booster pushrod.....3999
STEP 7. Retest the system.....3999
INSPECTION PROCEDURE 7: Squealing Noise when Brakes are not Applied....4000
DIAGNOSIS....4000
STEP 1. Check whether the backing plate is bent or loose and interfering with the drum.....4000
STEP 2. Check whether the drum is damaged due to interference with the backing plate or shoe.....4000
STEP 3. Check the brake drum for wear and the shoe spring for damage.....4000
STEP 4. Check the brake discs for rust.....4000
STEP 5. Check the brake pads for correct installation.....4000
STEP 6. Check the calipers for correct installation.....4000
STEP 7. Check the wheel bearings for end play.....4000
STEP 8. Adjust the brake pedal.....4001
STEP 9. Recheck symptom.....4001
INSPECTION PROCEDURE 8: Groaning, Clicking or Rattling Noise when Brakes are not Applied.....4001
DIAGNOSIS....4001
STEP 1. Check whether foreign material has entered the wheel covers.....4001
STEP 2. Check for looseness of the wheel nuts.....4001
STEP 3. Check for looseness of the caliper installation bolt.....4001
STEP 4. Check the wheel bearings for end play.....4001
STEP 5. Recheck symptom.....4001
SPECIAL TOOLS....4002
ON-VEHICLE SERVICE....4002
BRAKE PEDAL CHECK AND ADJUSTMENT....4002
BRAKE BOOSTER OPERATION CHECK....4004
CHECK VALVE OPERATION CHECK....4006
BLEEDING....4006
BRAKE FLUID LEVEL SENSOR CHECK....4007
BRAKE PAD CHECK....4008
BRAKE PAD REPLACEMENT....4008
BRAKE DISC CHECK....4009
BRAKE DRAG FORCE CHECK....4011
BRAKE LINING THICKNESS CHECK....4012
REAR WHEEL HUB ASSEMBLY INSIDE DIAMETER CHECK....4012
BRAKE LINING AND BRAKE DRUM CONTACT CHECK....4013
BRAKE PEDAL....4014
INSPECTION....4015
STOPLIGHT SWITCH CHECK....4015
MASTER CYLINDER ASSEMBLY AND BRAKE BOOSTER ASSEMBLY....4017
REMOVAL SERVICE POINT....4018
INSTALLATION SERVICE POINT....4018
FRONT DISC BRAKE ASSEMBLY....4019
REMOVAL SERVICE POINTS....4020
INSTALLATION SERVICE POINT....4020
DISASSEMBLY SERVICE POINTS....4023
INSPECTION....4024
BRAKE PAD WEAR INSPECTION....4024
REAR DRUM BRAKE....4025
REMOVAL SERVICE POINTS....4027
INSTALLATION SERVICE POINTS....4028
ASSEMBLY SERVICE POINT....4029
GR00004700-36....4032
PARKING BRAKES....4032
SERVICE SPECIFICATION....4033
PARKING BRAKE DIAGNOSIS....4033
SYMPTOM PROCEDURES....4033
INSPECTION PROCEDURE 1: Insufficient Parking Brake Function....4033
STEP 1. Check the excessive parking brake lever stroke.....4033
STEP 2. Check the parking brake cable for sticking.....4033
STEP 3. Check for oil, water, etc., on the lining contact surfaces.....4034
STEP 4. Retest the system.....4034
INSPECTION PROCEDURE 2: When the Parking Brake Lever is Pulled, the Brake Warning Light does not Illuminate.....4034
STEP 1. Using scan tool (M.U.T.-III), check combination meter special function.....4035
STEP 2. Check the parking brake switch.....4035
STEP 3. Connector check: C-115 parking brake switch connector and C-108 combination meter connector....4035
STEP 4. Check the wiring harness for an open circuit between C-115 parking brake switch connector terminal No.1 and C-108 combination meter connector terminal No.4.....4035
STEP 5. Retest the system.....4036
STEP 6. Retest the system.....4036
ON-VEHICLE SERVICE....4036
PARKING BRAKE LEVER STROKE CHECK AND ADJUSTMENT....4036
PARKING BRAKE SWITCH CHECK....4037
PARKING BRAKE LEVER....4038
INSTALLATION SERVICE POINT....4039
PARKING BRAKE CABLE....4040
INSTALLATION SERVICE POINTS....4040
GR00004800-42A....4042
BODY....4042
HOOD....4044
HOOD DIAGNOSIS....4044
SYMPTOM PROCEDURES....4044
INSPECTION PROCEDURE 1: Difficult Locking and Unlocking....4044
STEP 1. Check that the release cable is routed correctly.....4044
STEP 2. Check the engagement of the hood latch and hood striker.....4044
STEP 3. Check for proper lubrication of release cable.....4044
STEP 4. Retest the system.....4044
INSPECTION PROCEDURE 2: Uneven Body Clearance....4045
STEP 1. Check the clearance around the hood.....4045
STEP 2. Retest the system.....4045
INSPECTION PROCEDURE 3: Uneven Height....4045
STEP 1. Check the hood damper height.....4045
STEP 2. Retest the system.....4045
ON-VEHICLE SERVICE....4045
ADJUSTMENT OF CLEARANCE AROUND HOOD....4045
ADJUSTMENT OF HOOD LEVEL AND HOOD STRIKER ENGAGEMENT....4045
ADJUSTMENT OF HOOD HEIGHT....4046
HOOD....4047
REMOVAL SERVICE POINT....4048
INSTALLATION SERVICE POINT....4049
INSPECTION....4049
HOOD LATCH SWITCH CONTINUITY CHECK....4049
FENDER....4050
SPLASH SHIELD....4051
FUEL FILLER LID....4052
WINDOW GLASS....4053
SPECIFICATION(S)....4053
GENERAL INFORMATION....4053
WINDOW GLASS DIAGNOSIS....4055
SYMPTOM PROCEDURES....4055
INSPECTION PROCEDURE 1: Water Leak Through Windshield Glass/Water Leak Through Quarter Window Glass/Water Leak Though Liftgate Window Glass/Water Leak Though Roof Glass....4055
STEP 1. Check if the seal is faulty.....4055
STEP 2. Check if the body flange is deformed.....4055
STEP 3. Retest the system.....4055
WINDSHIELD....4056
REMOVAL SERVICE POINT....4057
INSTALLATION SERVICE POINTS....4059
LIFTGATE WINDOW GLASS....4062
REMOVAL SERVICE POINT....4063
INSTALLATION SERVICE POINTS....4063
DOOR....4065
CENTRAL DOOR LOCKING SYSTEM....4065
POWER WINDOWS....4066
SPECIFICATION(S)....4067
DOOR DIAGNOSIS....4069
STANDARD FLOW OF DIAGNOSTIC TROUBLESHOOTING....4069
SYMPTOM PROCEDURES <CENTRAL DOOR LOCKING SYSTEM>....4070
INSPECTION PROCEDURE 1: Central door locking system does not work at all.....4070
DIAGNOSIS....4070
STEP 1. Using scan tool MB991958, DTC check.....4070
STEP 2. Using scan tool MB991958, check data list.....4070
STEP 3. Check of short to power supply, short to ground, and open circuit in ETACS +B1 line between ETACS-ECU connector and fusible link (2).....4070
STEP 4. Retest the system.....4070
INSPECTION PROCEDURE 2: Door(s) or a liftgate cannot be locked or unlocked by central door locking system.....4071
DIAGNOSIS....4071
STEP 1. Confirmation of the defective door lock actuator or liftgate lock actuator.....4071
STEP 2. Front door lock actuator (LH) check....4071
STEP 3. Check of short to power supply, short to ground, and open circuit in RR-L, RL-U line between the ETACS-ECU connector and front door lock actuator (LH) connector....4071
STEP 4. Front door lock actuator (RH) check....4071
STEP 5. Check of short to power supply, short to ground, and open circuit in RR-L, RL-U line between the ETACS-ECU connector and the front door lock actuator (RH) connector....4071
STEP 6. Rear door lock actuator (LH) check....4071
STEP 7. Check of short to power supply, short to ground, and open circuit in RR-L, RL-U line between the ETACS-ECU connector and the rear door lock actuator (LH) connector....4071
STEP 8. Rear door lock actuator (RH) check....4071
STEP 9. Check of short to power supply, short to ground, and open circuit in RR-L, RL-U line between the ETACS-ECU connector and the rear door lock actuator (RH) connector....4072
STEP 10. Liftgate lock actuator check....4072
STEP 11. Check of short to power supply, short to ground, and open circuit in RR-L, RL-U line between the ETACS-ECU connector and the liftgate lock actuator connector....4072
INSPECTION PROCEDURE 3: Selector 'P' position-linked door unlock function does not operate <CVT>.....4072
DIAGNOSIS....4072
STEP 1. Checking central door unlocking operation....4072
STEP 2. Check the customization function.....4072
STEP 3. Using scan tool MB991958, diagnose the CAN bus lines.....4072
STEP 4. Check the scan tool MB991958 Diagnostic trouble code of other systems....4073
STEP 5. Retest the system.....4073
INSPECTION PROCEDURE 4: The ignition key reminder function does not work normally.....4073
DIAGNOSIS....4073
STEP 1. Check the power supply system.....4073
STEP 2. Using scan tool MB991958, check data list.....4073
STEP 3. Retest the system.....4074
SYMPTOM PROCEDURES <POWER WINDOW (Vehicles without safety system)>....4074
INSPECTION PROCEDURE 1: Power windows do not work at all.....4074
DIAGNOSIS....4075
STEP 1. Check the power supply system.....4075
STEP 2. Using scan tool MB991958, DTC check.....4075
STEP 3. Using scan tool MB991958, check data list.....4075
STEP 4. Check the power window relay.....4075
STEP 5. Voltage measurement at the power window relay connector (power supply line).....4075
STEP 6. Check of short to power supply, short to ground, and open circuit in power supply line between power window relay connector and fusible link.....4075
STEP 7. Voltage measurement at the power window relay connector (B. PW line).....4075
STEP 8. Check of short to power supply, short to ground, and open circuit in B. PW line between ETACS-ECU connector and power window relay connector.....4075
STEP 9. Resistance measurement at the power window relay connector (ground line).....4076
STEP 10. Check of open circuit in ground line between power window relay connector and body ground.....4076
STEP 11. Voltage measurement at the intermediate connector (power supply line).....4076
STEP 12. Check of short to power supply, short to ground, and open circuit in power supply line between power window relay connector and intermediate connector.....4076
STEP 13. Resistance measurement at the power window main switch connector (E line).....4076
STEP 14. Check of open circuit in E line between power window main switch connector and body ground.....4076
STEP 15. Retest the system.....4076
INSPECTION PROCEDURE 2: Front right power window does not work <Vehicles without driver’s side auto down mechanism>....4076
DIAGNOSIS....4077
STEP 1. Voltage measurement at the front power window switch (passenger’s side) connector (power supply line) connector (power....4077
STEP 2. Check of short to power supply, short to ground, and open circuit in power supply line between intermediate connector ....4077
STEP 3. Check the front power window switch (passenger’s side).....4077
STEP 4. Check the front power window motor (RH).....4077
STEP 5. Check of short to power supply, short to ground, and open circuit in input and output line between front power window ....4077
STEP 6. Check of open circuit in ground line between front power window switch (passenger’s side) connector and body ground.....4077
STEP 7. Retest the system.....4077
INSPECTION PROCEDURE 3: Front left power window does not work <Vehicles without driver’s side auto down mechanism>....4077
DIAGNOSIS....4078
STEP 1. Voltage measurement at the front power window switch (driver’s side) connector (power supply line).....4078
STEP 2. Check of short to power supply, short to ground, and open circuit in power supply line between intermediate connector ....4078
STEP 3. Check the front power window switch (driver’s side).....4078
STEP 4. Check the front power window motor (LH).....4078
STEP 5. Check of short to power supply, short to ground, and open circuit in input and output line between front power window ....4078
STEP 6. Check of open circuit in ground line between front power window switch (driver’s side) connector and body ground.....4078
STEP 7. Retest the system.....4078
INSPECTION PROCEDURE 4: Driver' power window does not work by means of the power window main switch <Vehicles with driver’s s....4078
DIAGNOSIS....4079
STEP 1. Check the power window main switch.....4079
STEP 2. Voltage measurement at power window main switch connector (+B line).....4079
STEP 3. Check of short to power supply, short to ground, and open circuit in +B line between the fusible link (6) and the power window main switch connector .....4079
STEP 4. Check of short to power supply, short to ground, and open circuit in U.DR, D.DR line between the power window main switch connector and front power window motor (LH) connector.....4079
STEP 5. Retest the system.....4079
INSPECTION PROCEDURE 5: Relevant power window does not work by means of the front passenger' power window sub switch <Vehicle....4079
DIAGNOSIS....4080
STEP 1. Check the power window main switch.....4080
STEP 2. Check the front power window sub switch....4080
STEP 3. Check the front power window motor (LH)....4080
STEP 4. Voltage measurement at front power window sub switch connector (power supply line)....4080
STEP 5. Check of short to power supply, short to ground, and open circuit in power supply line between the front power window sub switch connector and the power window relay connector....4080
STEP 6. Check of short to power supply, short to ground, and open circuit in input/output line between the front power window sub switch connector and the front power window motor (LH) connector....4080
STEP 7. Retest the system.....4080
INSPECTION PROCEDURE 6: Front passenger' power window does not work by means of the power window main switch <Vehicles with d....4080
DIAGNOSIS....4081
STEP 1. Check the power window main switch.....4081
STEP 2. Check the power window sub switch.....4081
STEP 3. Check of short to power supply, short to ground, and open circuit in input/output line between power window main switch connector and front power window sub switch connector.....4081
STEP 4. Retest the system.....4081
INSPECTION PROCEDURE 7: Power window timer function does not work normally.....4081
DIAGNOSIS....4081
SYMPTOM PROCEDURES <POWER WINDOW (Vehicles with safety system)>....4082
INSPECTION PROCEDURE 1: Power windows do not work at all.....4082
DIAGNOSIS....4082
STEP 1. Check the power supply system.....4082
STEP 2. Using scan tool MB991958, DTC check.....4082
STEP 3. Using scan tool MB991958, check data list.....4083
STEP 4. Check the power window relay.....4083
STEP 5. Voltage measurement at the power window relay connector (power supply line).....4083
STEP 6. Check of short to power supply, short to ground, and open circuit in power supply line between power window relay connector and fusible link.....4083
STEP 7. Voltage measurement at the power window relay connector (B. PW line).....4083
STEP 8. Check of short to power supply, short to ground, and open circuit in B. PW line between ETACS-ECU connector and power window relay connector.....4083
STEP 9. Resistance measurement at the power window relay connector (ground line).....4083
STEP 10. Check of open circuit in ground line between power window relay connector and body ground.....4083
STEP 11. Retest the system.....4084
INSPECTION PROCEDURE 2: Driver' power window does not work by means of the power window main switch.....4084
DIAGNOSIS....4084
STEP 1. Check the power window main switch.....4084
STEP 2. Voltage measurement at power window main switch connector (+BP line).....4084
STEP 3. Check of short to power supply, short to ground, and open circuit in +BP line between the fusible link and the power window main switch connector .....4084
STEP 4. Check of short to power supply, short to ground, and open circuit in MU, MD line between the power window main switch connector and front power window motor (LH) connector.....4084
STEP 5. Retest the system.....4085
INSPECTION PROCEDURE 3: Relevant power window(s) does not work by means of the front and rear passenger' power window sub switches.....4085
DIAGNOSIS....4085
STEP 1. Check the power window main switch.....4085
STEP 2. Using scan tool MB991958, DTC check.....4085
STEP 3. Determine a trouble spot.....4085
STEP 4. Check the front power window sub switch....4085
STEP 5. Check the front power window motor (RH)....4085
STEP 6. Voltage measurement at front power window sub switch connector (power supply line)....4086
STEP 7. Check of short to power supply, short to ground, and open circuit in power supply line between the front power window sub switch connector and the power window relay connector....4086
STEP 8. Check of short to power supply, short to ground, and open circuit in input/output line between the front power window sub switch connector and the front power window motor (RH) connector....4086
STEP 9. Retest the system.....4086
STEP 10. Check the rear power window sub switch (RH)....4086
STEP 11. Check the rear power window motor (RH)....4086
STEP 12. Voltage measurement at rear power window sub switch (RH) connector (power supply line)....4086
STEP 13. Check of short to power supply, short to ground, and open circuit in power supply line between the rear power window sub switch (RH) connector and the power window relay connector....4086
STEP 14. Check of short to power supply, short to ground, and open circuit in input/output line between the rear power window sub switch (RH) connector and the rear power window motor (RH) connector....4087
STEP 15. Retest the system.....4087
STEP 16. Check the rear power window sub switch (LH)....4087
STEP 17. Check the rear power window motor (LH)....4087
STEP 18. Voltage measurement at rear power window sub switch (LH) connector (power supply line)....4087
STEP 19. Check of short to power supply, short to ground, and open circuit in power supply line between the rear power window sub switch (LH) connector and the power window relay connector....4087
STEP 20. Check of short to power supply, short to ground, and open circuit in input/output line between the rear power window sub switch (LH) connector and the rear power window motor (LH) connector....4087
STEP 21. Retest the system.....4087
INSPECTION PROCEDURE 4: Front and/or rear passenger' power window(s) do not work by means of the power window main switch.....4088
DIAGNOSIS....4088
STEP 1. Check the power window main switch.....4088
STEP 2. Check the power window sub switch.....4088
STEP 3. Determine a trouble spot.....4088
STEP 4. Check of short to power supply, short to ground, and open circuit in input/output line between power window main switch connector and front power window sub switch connector.....4088
STEP 5. Retest the system.....4088
STEP 6. Check of short to power supply, short to ground, and open circuit in input/output line between power window main switch connector and rear power window sub switch (RH) connector.....4088
STEP 7. Retest the system.....4088
STEP 8. Check of short to power supply, short to ground, and open circuit in input/output line between power window main switch connector and rear power window sub switch (LH) connector.....4088
STEP 9. Retest the system.....4089
INSPECTION PROCEDURE 5: Power window timer function does not work normally.....4089
DIAGNOSIS....4089
INSPECTION PROCEDURE 6: Power window anti-trap function does not work normally <Driver’s side door>.....4089
DIAGNOSIS....4089
STEP 1. Check the power window fully closed position....4089
STEP 2. Check of short to power supply, short to ground, and open circuit in VCC, SEN1, SEN2, SGND line between the power window main switch connector and the front power window motor (RH) connector....4090
STEP 3. Retest the system.....4090
INSPECTION PROCEDURE 7: Window glass lowers automatically while it is rising <Driver’s side door>.....4090
DIAGNOSIS....4090
STEP 1. Check the power window fully closed position....4090
STEP 2. Check of short to power supply, short to ground, and open circuit in VCC, SEN1, SEN2, SGND line between the power window main switch connector and the front power window motor (LH) connector....4090
STEP 3. Retest the system.....4090
STEP 4. Retest the system.....4091
INSPECTION PROCEDURE 8: Power window main switch one-touch function does not work <Driver’s side door>.....4091
DIAGNOSIS....4091
STEP 1. Check the power window fully closed position....4091
STEP 2. Check of short to power supply, short to ground, and open circuit in VCC, SEN1, SEN2, SGND line between the power window main switch connector and the front power window motor (LH) connector....4091
STEP 3. Retest the system.....4091
STEP 4. Retest the system.....4091
POWER WINDOW MAIN SWITCH TERMINAL CHECK....4092
ON-VEHICLE SERVICE....4093
DOOR ADJUSTMENT....4093
DOOR WINDOW GLASS ADJUSTMENT....4094
ADJUSTMENT OF FAULTY POWER WINDOW....4096
POWER WINDOW SAFETY MECHANISM CHECK <Vehicles with safety system (driver’s side door)>....4096
POWER WINDOW TIMER FUNCTION CHECK....4096
POWER WINDOW OPERATING CURRENT CHECK....4097
CHECK THE POWER WINDOW RELAY....4097
LEARNING PROCEDURES OF POWER WINDOW FULLY CLOSED POSITION <Vehicles with safety system (driver’s side door)>....4098
LEARNING PROCEDURES OF FULLY CLOSED POSITION WHEN POWER WINDOW SWITCH IS REMOVED, OR POWER WINDOW REGULATOR ASSEMBLY IS REMOVED OR REPLACED....4098
LEARNING PROCEDURES WHEN POWER WINDOW SWITCH IS REPLACED WITH A NEW ONE....4098
CENTRAL DOOR LOCKING SYSTEM CHECK....4098
KEY REMINDER FUNCTION INSPECTION....4099
SELECTOR 'P' POSITION-LINKED DOOR UNLOCKING FUNCTION CHECK <CVT>....4099
DOOR LATCH ASSEMBLY INSPECTION....4099
DOOR LOCK ACTUATOR....4100
DOOR OUTSIDE HANDLE ASSEMBLY PLAY CHECK....4103
DOOR INSIDE HANDLE CHECK....4104
DOOR INSIDE HANDLE KNOB PLAY CHECK....4104
DOOR INSIDE HANDLE LOCK KNOB STROKE CHECK....4104
DOOR ASSEMBLY....4105
INSTALLATION SERVICE POINT....4107
INSPECTION....4107
DOOR SWITCH CHECK....4107
DOOR GLASS AND REGULATOR....4108
REMOVAL SERVICE POINT....4109
INSTALLATION SERVICE POINT....4110
INSPECTION....4110
POWER WINDOW MAIN SWITCH CONTINUITY CHECK <Vehicles with safety system>....4110
POWER WINDOW SUB SWITCH CONTINUITY CHECK <Vehicles with safety system>....4111
POWER WINDOW MAIN SWITCH CONTINUITY CHECK <Vehicles without safety system (Vehicles with driver’s side auto down mechanism)>....4111
POWER WINDOW SUB SWITCH CONTINUITY CHECK <Vehicles without safety system (Vehicles with driver’s side auto down mechanism)>....4112
POWER WINDOW SWITCH CONTINUITY CHECK <Vehicles without safety system (Vehicles without driver’s side auto down mechanism)>....4112
POWER WINDOW MOTOR CONTINUITY CHECK....4113
DOOR HANDLE AND LATCH....4114
REMOVAL SERVICE POINT....4116
INSTALLATION SERVICE POINTS....4116
INSPECTION....4117
DOOR LOCK ACTUATOR CHECK....4117
WINDOW GLASS RUNCHANNEL AND DOOR OPENING WEATHERSTRIP....4118
REMOVAL SERVICE POINT....4120
INSTALLATION SERVICE POINT....4121
LIFTGATE....4121
ON-VEHICLE SERVICE....4122
LIFTGATE ALIGNMENT....4122
ADJUSTMENT OF ENGAGEMENT BETWEEN STRIKER AND LATCH....4122
ADJUSTMENT OF CLEARANCE BETWEEN LIFTGATE AND BODY....4123
ADJUSTMENT OF LIFTGATE HEIGHT....4123
LIFTGATE OUTSIDE HANDLE PLAY CHECK....4124
LIFTGATE....4125
REMOVAL SERVICE POINTS....4126
INSTALLATION SERVICE POINTS....4127
LIFTGATE HANDLE AND LATCH....4128
INSTALLATION SERVICE POINT....4129
INSPECTION....4129
LIFTGATE LOCK ACTUATOR CHECK....4129
LIFTGATE LATCH SWITCH CHECK....4130
KEYLESS ENTRY SYSTEM <Vehicles without Keyless operation system>....4130
KEYLESS ENTRY SYSTEM DIAGNOSIS....4130
DIAGNOSIS TROUBLESHOOTING FLOW....4130
SYMPTOM PROCEDURES....4131
Inspection Procedure 1: Keyless entry system does not work.....4131
DIAGNOSIS....4131
STEP 1. Using scan tool MB991958, DTC check.....4131
STEP 2. Check the power supply circuit.....4131
STEP 3. Check the operation of the central door locking system.....4131
STEP 4. Using scan tool MB991958, check data list.....4132
STEP 5. Retest the system.....4132
Inspection Procedure 2: Keyless entry hazard light answerback function or the dome light answerback function does not work normally.....4133
DIAGNOSIS....4133
STEP 1. Check the operation of the hazard warning light.....4133
STEP 2. Check the operation of the dome light.....4133
STEP 3. Check the operation of the keyless entry system.....4133
STEP 4. Check the customization function.....4134
STEP 5. Retest the system.....4134
Inspection Procedure 3: The timer lock function does not work after the doors have been unlocked by the keyless entry system.....4134
DIAGNOSIS....4134
Inspection Procedure 4: Power door locks with selective unlocking does not work.....4135
DIAGNOSIS....4135
STEP 1. Check the customization....4135
STEP 2. Keyless entry system operation check....4135
STEP 3. Check of the troubles....4135
ON-VEHICLE SERVICE....4138
KEYLESS ENTRY SYSTEM INSPECTION....4138
KEYLESS ENTRY SYSTEM TIMER LOCK FUNCTION INSPECTION....4139
HOW TO REGISTER ENCRYPTED CODE....4139
TRANSMITTER....4140
DISASSEMBLY SERVICE POINTS....4141
ASSEMBLY SERVICE POINT....4141
LOOSE PANEL....4142
GR00004900-52A....4144
INTERIOR....4144
SPECIAL TOOL....4145
INSTRUMENT PANEL ASSEMBLY....4145
REMOVAL SERVICE POINT....4147
GLOVE BOX....4147
INSTRUMENT CENTER PANEL....4148
REMOVAL SERVICE POINT....4148
INSTRUMENT LOWER PANEL....4149
FLOOR CONSOLE ASSEMBLY....4150
REMOVAL SERVICE POINT....4151
INSTALLATION SERVICE POINT....4151
TRIMS....4152
INTERIOR TRIM....4152
DOOR TRIM....4154
LIFTGATE TRIM....4157
HEADLINING....4158
REMOVAL SERVICE POINTS....4159
INSIDE REAR VIEW MIRROR....4159
REMOVAL SERVICE POINT....4159
SEAT ASSEMBLY....4160
FRONT SEAT ASSEMBLY....4160
REMOVAL SERVICE POINT....4161
INSTALLATION SERVICE POINT....4161
INSPECTION....4162
CONTINUITY TEST OF HEATED SEAT SWITCH <VEHICLES WITH HEATED SEAT>....4162
SEAT CUSHION HEATER CHECK <VEHICLES WITH HEATED SEAT>....4162
SEATBACK HEATER CHECK <VEHICLES WITH HEATED SEAT>....4163
HEATED SEAT RELAY CONTINUITY CHECK <VEHICLES WITH HEATED SEAT>....4163
SEAT BELT REMINDER SENSOR CHECK <PASSENGER’S SIDE>....4163
DISASSEMBLY SERVICE POINT....4166
REAR SEAT ASSEMBLY....4166
REMOVAL SERVICE POINT....4167
INSTALLATION SERVICE POINT....4168
DISASSEMBLY SERVICE POINT....4170
SEAT BELT....4170
FRONT SEAT BELT....4170
INSPECTION....4171
REAR SEAT BELT....4172
GR00005000-54....4174
CHASSIS ELECTRICAL....4174
GR00005100-54A....4176
CHASSIS ELECTRICAL....4176
BATTERY....4179
ON-VEHICLE SERVICE....4179
FLUID LEVEL AND SPECIFIC GRAVITY CHECK....4179
CHARGE RATE....4180
STEP 1. Check the battery cables.....4180
STEP 2. Check the battery posts.....4180
STEP 3. Check the battery case and cover.....4180
STEP 4. Check the open circuit voltage.....4180
STEP 5. Battery charging....4181
STEP 6. Check the load test.....4181
IGNITION SWITCH....4183
DIAGNOSIS....4183
STANDARD FLOW OF DIAGNOSTIC TROUBLE SHOOTING....4183
SYMPTOM PROCEDURES....4184
Malfunction of the ignition switch power supply system....4184
DIAGNOSIS....4184
STEP 1. Check the battery power supply circuit to the ignition switch. Measure the voltage at ignition switch connector.....4184
STEP 2. Check the fuse.....4184
STEP 3. Check of open circuit in power supply line between ignition switch connector and junction block connector....4184
STEP 4. Check the ignition switch.....4184
STEP 5. Retest the system.....4184
ON-VEHICLE SERVICE....4184
IGNITION KEY REMINDER TONE ALARM INSPECTION....4184
REMOVAL SERVICE POINT....4186
INSPECTION....4187
IGNITION SWITCH CHECK....4187
KEY REMINDER SWITCH INSPECTION....4187
COMBINATION METER....4187
DIAGNOSIS....4190
STANDARD FLOW OF DIAGNOSTIC TROUBLESHOOTING....4190
HOW TO CONNECT THE SCAN TOOL (M.U.T.-III)....4190
HOW TO READ AND ERASE DIAGNOSTIC TROUBLE CODES....4191
HOW TO DIAGNOSE THE CAN BUS LINES....4192
CHECK OF FREEZE FRAME DATA....4193
DIAGNOSTIC TROUBLE CODE PROCEDURES....4194
DTC B1200: Odometer failure....4194
DTC B1201: Fuel information problem....4194
DIAGNOSIS....4194
STEP 1. Check of fuel pump and gauge assembly circuit....4195
STEP 2. Check the fuel level sensor.....4195
STEP 3. Resistance measurement at the fuel pump and gauge assembly connector....4195
STEP 4. Check of open circuit in ground line between fuel pump and gauge assembly connector and ground.....4195
STEP 5. Check of open circuit in F/G line between combination meter connector and fuel pump and gauge assembly connector.....4195
STEP 6. Using scan tool (M.U.T.-III), perform actuator test.....4196
STEP 7. Recheck for diagnostic trouble code.....4196
DTC B1209: B1209 Test mode....4196
DTC B2463: Rheostat switch sticking....4196
DTC U0100: Engine CAN timeout....4196
DIAGNOSIS....4197
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line....4197
STEP 2. Using scan tool (M.U.T.-III), read the engine control module diagnostic trouble code....4197
STEP 3. Using scan tool (M.U.T.-III), read the ETACS diagnostic trouble code.....4197
STEP 4. Recheck for diagnostic trouble code.....4197
STEP 5. Recheck for diagnostic trouble code.....4197
STEP 6. Recheck for diagnostic trouble code.....4197
DTC U0101: T/M CAN timeout....4197
DIAGNOSIS....4198
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line....4198
STEP 2. Using scan tool (M.U.T.-III), read the CVT diagnostic trouble code....4198
STEP 3. Using scan tool (M.U.T.-III), read the ETACS diagnostic trouble code.....4198
STEP 4. Recheck for diagnostic trouble code.....4198
STEP 5. Recheck for diagnostic trouble code.....4198
STEP 6. Check whether the DTC is reset.....4198
DTC U0121: ABS/ASC CAN timeout....4199
DIAGNOSIS....4199
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line....4199
STEP 2. Using scan tool (M.U.T.-III), read the ASC diagnostic trouble code....4199
STEP 3. Using scan tool (M.U.T.-III), read the ETACS diagnostic trouble code.....4199
STEP 4. Recheck for diagnostic trouble code.....4199
STEP 5. Recheck for diagnostic trouble code.....4199
STEP 6. Recheck for diagnostic trouble code.....4200
DTC U0131: EPS CAN timeout....4200
DIAGNOSIS....4200
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line....4200
STEP 2. Using scan tool (M.U.T.-III), read the EPS diagnostic trouble code.....4200
STEP 3. Using scan tool (M.U.T.-III), read the ETACS diagnostic trouble code.....4200
STEP 4. Recheck for diagnostic trouble code.....4201
STEP 5. Recheck for diagnostic trouble code.....4201
STEP 6. Recheck for diagnostic trouble code.....4201
DTC U0141: ETACS CAN timeout....4201
DIAGNOSIS....4201
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line....4201
STEP 2. Using scan tool (M.U.T.-III), read the ETACS diagnostic trouble code....4202
STEP 3. Using scan tool (M.U.T.-III), read the MFI diagnostic trouble code....4202
STEP 4. Recheck for diagnostic trouble code.....4202
STEP 5. Recheck for diagnostic trouble code.....4202
STEP 6. Recheck for diagnostic trouble code.....4202
DTC U0151: SRS-ABG CAN timeout....4202
DIAGNOSIS....4203
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line....4203
STEP 2. Using scan tool (M.U.T.-III), read the SRS diagnostic trouble code....4203
STEP 3. Recheck for diagnostic trouble code.....4203
STEP 4. Recheck for diagnostic trouble code.....4203
STEP 5. Recheck for diagnostic trouble code.....4203
DTC U0154: OCM CAN timeout....4203
DIAGNOSIS....4204
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line....4204
STEP 2. Using scan tool (M.U.T.-III), read the OCM diagnostic trouble code....4204
STEP 3. Using scan tool (M.U.T.-III), read the SRS diagnostic trouble code.....4204
STEP 4. Recheck for diagnostic trouble code.....4204
STEP 5. Recheck for diagnostic trouble code.....4204
STEP 6. Recheck for diagnostic trouble code.....4205
DTC U0168: WCM/F.A.S.T. CAN timeout....4205
DIAGNOSIS....4205
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line....4205
STEP 2. Using scan tool (M.U.T.-III), read the KOS diagnostic trouble code....4205
STEP 3. Using scan tool (M.U.T.-III), read the ETACS diagnostic trouble code....4205
STEP 4. Recheck for diagnostic trouble code.....4206
STEP 5. Recheck for diagnostic trouble code.....4206
STEP 6. Recheck for diagnostic trouble code.....4206
DTC U1000: OSS CAN timeout....4206
DIAGNOSIS....4206
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line....4206
STEP 2. Using scan tool (M.U.T.-III), read the KOS diagnostic trouble code....4207
STEP 3. Using scan tool (M.U.T.-III), read the ETACS diagnostic trouble code....4207
STEP 4. Recheck for diagnostic trouble code.....4207
STEP 5. Recheck for diagnostic trouble code.....4207
STEP 6. Recheck for diagnostic trouble code.....4207
DTC U1110: A/C CAN timeout/Not equipped....4207
DIAGNOSIS....4208
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line....4208
STEP 2. Using scan tool (M.U.T.-III), read the A/C diagnostic trouble code....4208
STEP 3. Using scan tool (M.U.T.-III), read the ETACS diagnostic trouble code....4208
STEP 4. Recheck for diagnostic trouble code.....4208
STEP 5. Recheck for diagnostic trouble code.....4208
STEP 6. Recheck for diagnostic trouble code.....4208
DTC U1190: No receive fault detect signal....4208
DIAGNOSIS....4209
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line....4209
STEP 2. Recheck for diagnostic trouble code.....4209
STEP 3. Recheck for diagnostic trouble code.....4209
DTC U1195: Coding not completed....4209
DIAGNOSIS....4209
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line....4209
STEP 2. Using scan tool (M.U.T.-III), read the ETACS diagnostic trouble code....4210
STEP 3. Recheck for diagnostic trouble code.....4210
SYMPTOM PROCEDURES....4211
Inspection Procedure 1: Power supply circuit check Inspection Procedure 2: The odometer and the trip meter are not displayed. In.....4211
DIAGNOSIS....4211
STEP 1. Using scan tool (M.U.T.-III), read the combination meter diagnostic trouble code....4211
STEP 2. Voltage measurement at the combination meter connector....4212
STEP 3. Check of open circuit in B+B line between the fusible link and combination meter connector.....4212
STEP 4. Voltage measurement at the combination meter connector....4212
STEP 5. Using scan tool (M.U.T.-III), check data list....4212
STEP 6. Check of open circuit in IG1 line between the ignition switch (IG1) and combination meter connector.....4213
STEP 7. Resistance measurement at the combination meter connector....4213
STEP 8. Check of open circuit in GND line between combination meter connector and ground.....4213
STEP 9. Retest the system....4213
Inspection Procedure 5: The speedometer does not work (The other meters work).....4213
DIAGNOSIS....4214
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....4214
STEP 2. Using scan tool (M.U.T.-III), read the MFI diagnostic trouble code.....4214
STEP 3. Using scan tool (M.U.T.-III), check data list....4214
STEP 4. Using scan tool (M.U.T.-III), check actuator test.....4214
STEP 5. Check by scan tool (M.U.T.-III) 'Special Function'....4215
STEP 6. Retest the system.....4215
Inspection Procedure 6: The tachometer does not work (the other meters work).....4215
DIAGNOSIS....4215
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line....4215
STEP 2. Using scan tool (M.U.T.-III), read the combination meter diagnostic trouble code....4215
STEP 3. Using scan tool (M.U.T.-III), read the MFI diagnostic trouble code.....4216
STEP 4. Using scan tool (M.U.T.-III), check actuator test....4216
STEP 5. Check by scan tool (M.U.T.-III) 'Special Function'....4216
STEP 6. Retest the system....4216
Inspection Procedure 7: Tone alarm does not sound normally.....4216
DIAGNOSIS....4217
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line....4217
STEP 2. Using scan tool (M.U.T.-III), read the combination meter diagnostic trouble code....4217
STEP 3. Using scan tool (M.U.T.-III), read for any diagnostic trouble code....4217
STEP 4. Check by scan tool (M.U.T.-III) 'Special Function'....4217
STEP 5. Retest the system....4217
Inspection Procedure 8: Fuel gauge does not work (the other meters work).....4217
DIAGNOSIS....4218
STEP 1. Using scan tool (M.U.T.-III), read the combination meter diagnostic trouble code.....4218
STEP 2. Check the fuel level sensor....4218
STEP 3. Using scan tool (M.U.T.-III), check data list....4218
STEP 4. Using scan tool (M.U.T.-III), check actuator test....4218
STEP 5. Retest the system.....4218
Inspection Procedure 9: The combination meter light does not illuminate normally or the multi-information display is not displayed normally.....4219
DIAGNOSIS....4219
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line....4219
STEP 2. Using scan tool (M.U.T.-III), read the combination meter diagnostic trouble code....4219
STEP 3. Using scan tool (M.U.T.-III), read for any diagnostic trouble code.....4219
STEP 4. Check by scan tool (M.U.T.-III) 'Special Function'....4219
STEP 5. Retest the system....4220
Inspection Procedure 10: The multi-information display screen cannot be changed with the operation of the multi-information display switch.....4220
DIAGNOSIS....4220
STEP 1. Using scan tool (M.U.T.-III), read the combination meter diagnostic trouble code.....4220
STEP 2. Check by scan tool (M.U.T.-III) 'Special Function'....4221
STEP 3. Retest the system.....4221
Inspection Procedure 11: Parking brake reminder tone alarm does not sound. Inspection Procedure 12: Brake warning light does not illuminate.....4221
DIAGNOSIS....4221
STEP 1. Check the speedometer.....4221
STEP 2. Check the parking brake switch.....4221
STEP 3. Check of short to power supply, and open circuit in BRK line between combination meter connector and parking brake switch connector.....4221
STEP 4. Check by scan tool (M.U.T.-III) 'Special Function'....4222
STEP 5. Retest the system.....4222
Inspection Procedure 13: Ambient temperature sensor does not work.....4222
DIAGNOSIS....4222
STEP 1. Check the ambient temperature sensor.....4222
STEP 2. Resistance measurement at the ambient temperature sensor connector....4222
STEP 3. Check of open circuit in SENG line between ambient temperature sensor connector and combination meter connector.....4223
STEP 4. Check of open circuit in AMB line between combination meter connector and ambient temperature sensor connector.....4223
STEP 5. Retest the system.....4223
Inspection Procedure 14: Seat belt reminder function does not work normally.....4223
DIAGNOSIS....4223
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line....4224
STEP 2. Using scan tool (M.U.T.-III), read the SRS diagnostic trouble code.....4224
STEP 3. Check the seat belt switch.....4224
STEP 4. Resistance measurement at the seat belt switch (driver’s side) connector....4224
STEP 5. Check of open circuit in ground line between seat belt switch (driver’s side) and ground.....4224
STEP 6. Check of short to power supply circuit in S/B- line between combination meter connector and seat belt switch (driver’s....4225
STEP 7. Check of short to power supply, and open circuit in BWLP line between combination meter connector and passenger’s air ....4225
STEP 8. Retest the system.....4225
ON-VEHICLE SERVICE....4228
SPEEDOMETER CHECK....4228
TACHOMETER CHECK....4229
HOW TO SET BY OPERATING THE SCAN TOOL (M.U.T.-III)....4230
HOW TO SET BY SPECIAL OPERATION OF SWITCH....4234
HOW TO INACTIVATE THE SERVICE REMINDER FUNCTION....4235
COMBINATION METER....4236
HEADLIGHT....4237
PRECAUTIONS ON HOW TO USE THE HEADLIGHT ASSEMBLY....4237
DIAGNOSIS....4240
DIAGNOSTIC FUNCTION....4240
HOW TO CONNECT THE SCAN TOOL (M.U.T.-III)....4240
HOW TO READ AND ERASE DIAGNOSTIC TROUBLE CODES....4241
HOW TO DIAGNOSE THE CAN BUS LINES....4242
DIAGNOSTIC TROUBLE CODE PROCEDURES....4243
DTC B1706: Flasher fuse blown....4243
DIAGNOSIS....4243
STEP 1. Check the flasher fuse.....4243
STEP 2. Check of open circuit in HAZ1 line between the ETACS-ECU connector and the fusible link.....4243
STEP 3. Using scan tool (M.U.T.-III), Check whether the diagnostic trouble code is stored again.....4244
DTC B1707: Flasher open....4244
DIAGNOSIS....4244
STEP 1. Confirm which turn-signal light is defective.....4244
STEP 2. Check the bulb(s) of the front turn-signal lights.....4245
STEP 3. Resistance measurement at the front turn-signal light (LH) connector or front turn-signal light (RH) connector.....4245
STEP 4. Check of open circuit in ground line between front turn-signal light (LH) connector or front turn-signal light (RH) connector and ground.....4245
STEP 5. Check of open circuit in TURN LH or TURN RH line between front turn-signal light (LH) connector or front turn-signal light (RH) connector and ETACS-ECU connector.....4245
STEP 6. Retest the system.....4246
STEP 7. Check the bulb(s) of side turn-signal lights.....4246
STEP 8. Resistance measurement at the side turn-signal light (LH) connector, side turn-signal light (RH) connector <Fender panel type>, door mirror assembly (LH) connector or door mirror assembly (RH) connector <Door mirror type>.....4246
STEP 9. Check of open circuit in ground line between side turn-signal light (LH) connector, side turn-signal light (RH) connecto.....4247
STEP 10. Check of open circuit in TURN LH or TURN RH line between side turn-signal light (LH) connector, side turn-signal light .....4247
STEP 11. Retest the system.....4247
STEP 12. Check the bulb(s) of rear turn-signal lights.....4247
STEP 13. Resistance measurement at the rear combination light (turn: LH) or rear combination light (turn: RH) connector.....4248
STEP 14. Check of open circuit in ground line between rear combination light (turn: LH) connector or rear combination light (turn: RH) connector and ground.....4248
STEP 15. Check of open circuit in TURN LH or TURN RH line between rear combination light (turn: LH) connector or rear combination light (turn: RH) connector and ETACS-ECU connector.....4248
STEP 16. Retest the system.....4248
STEP 17. Using scan tool (M.U.T.-III), Check whether the diagnostic trouble code is set again.....4249
SYMPTOM PROCEDURES....4250
Inspection Procedure A-1: None of the low-beam headlights illuminate.....4250
DIAGNOSIS....4250
STEP 1. Using scan tool (M.U.T.-III), read the diagnostic trouble code.....4250
STEP 2. Using scan tool (M.U.T.-III), check data list....4250
STEP 3. Check the headlight relay (LO).....4251
STEP 4. Voltage measurement at headlight relay (LO) connector.....4251
STEP 5. Check of short to power supply, and open circuit in power supply lines between headlight relay (LO) connector and fusible link.....4251
STEP 6. Check of open circuit in H/LP LO line between headlight relay (LO) connector and ETACS-ECU connector.....4251
STEP 7. Retest the system.....4251
Inspection Procedure A-2: None of the high-beam headlights illuminate.....4251
DIAGNOSIS....4252
STEP 1. Using scan tool (M.U.T.-III), read the diagnostic trouble code.....4252
STEP 2. Using scan tool (M.U.T.-III), check data list....4252
STEP 3. Check the headlight relay (HI).....4252
STEP 4. Voltage measurement at headlight relay (HI) connector.....4253
STEP 5. Check of short to power supply, and open circuit in power supply lines between headlight relay (HI) connector and fusible link.....4253
STEP 6. Check of open circuit in H/LP HI line between headlight relay (HI) connector and ETACS-ECU connector.....4253
STEP 7. Retest the system.....4253
Inspection Procedure A-3: The high-beam and low-beam headlights do not illuminate when the passing switch is operated.....4253
DIAGNOSIS....4254
STEP 1. Using scan tool (M.U.T.-III), read the ETACS-ECU diagnostic trouble code.....4254
STEP 2. Check that the headlights operate.....4254
STEP 3. Retest the system.....4254
Inspection Procedure A-4: One of the headlights does not illuminate.....4254
DIAGNOSIS....4254
STEP 1. Bulb check....4254
STEP 2. Resistance measurement at the headlight (LH) connector, headlight (RH) connector....4255
STEP 3. Check of open circuit in ground line between headlight (LH) connector or headlight (RH) connector and ground.....4255
STEP 4. Check of short to power supply, and open circuit in power supply line between headlight (LH) connector or headlight (RH) connector and headlight relay (LO) connector.....4255
STEP 5. Retest the system....4255
Inspection Procedure A-5: The high-beam indicator light does not illuminate.....4255
DIAGNOSIS....4256
STEP 1. Check the headlight.....4256
STEP 2. Using scan tool (M.U.T.-III), diagnose the CAN bus line....4256
STEP 3. Using scan tool (M.U.T.-III), read the ETACS diagnostic trouble code.....4256
STEP 4. Check by scan tool (M.U.T.-III) 'Special Function'....4256
Inspection Procedure A-6: The headlight automatic-shutdown function does not work normally.....4256
DIAGNOSIS....4257
STEP 1. Using scan tool (M.U.T.-III), Check the configuration function....4257
STEP 2. Using scan tool (M.U.T.-III), read the diagnostic trouble code.....4257
STEP 3. Using scan tool (M.U.T.-III), check data list....4257
STEP 4. Retest the system.....4257
Inspection Procedure A-7: The position light does not illuminate.....4257
DIAGNOSIS....4258
STEP 1. Using scan tool (M.U.T.-III), read the diagnostic trouble code.....4258
STEP 2. Using scan tool (M.U.T.-III), check data list....4258
STEP 3. Retest the system.....4258
Inspection Procedure A-8: Either of the position lights does not illuminate.....4258
DIAGNOSIS....4259
STEP 1. Bulb check....4259
STEP 2. Resistance measurement at position light (LH) connector, position light (RH) connector....4259
STEP 3. Check of open circuit in ground line between position light (LH) connector or position light (RH) connector and ground.....4259
STEP 4. Check of short to power supply, and open circuit in power supply line between position light (LH) connector or position light (RH) connector and junction block connector.....4259
STEP 5. Retest the system.....4260
Inspection Procedure A-9: When the ignition switch is turned to the ON position with the lighting switch at the OFF or TAIL position, the headlights will illuminate briefly.....4260
DIAGNOSIS....4260
STEP 1. Check dome light fuse.....4260
STEP 2. Check that the headlights operate.....4260
STEP 3. Using scan tool (M.U.T.-III), read the ETACS diagnostic trouble code....4261
STEP 4. Voltage measurement at column switch connector.....4261
STEP 5. Check of short to power supply, and open circuit in power supply line between column switch connector and junction block connector.....4261
STEP 6. Retest the system.....4261
Inspection Procedure A-10: Daytime running light function does not work normally.....4262
DIAGNOSIS....4262
STEP 1. Verify the headlight (low-beam) operation.....4262
STEP 2. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....4262
STEP 3. Using scan tool (M.U.T.-III), read the ETACS-ECU diagnostic trouble code.....4262
STEP 4. Using scan tool (M.U.T.-III), read the MFI system diagnostic trouble code.....4263
STEP 5. Check the parking brake switch.....4263
STEP 6. Temporarily replace the headlight relay (LO), and retest the system.....4263
Inspection Procedure B-1: None of the turn-signal lights illuminate.....4263
DIAGNOSIS....4264
STEP 1. Using scan tool (M.U.T.-III), read the diagnostic trouble code....4264
STEP 2. Using scan tool (M.U.T.-III), check data list....4264
STEP 3. Retest the system....4264
Inspection Procedure B-2: The comfort flasher does not work normally.....4264
DIAGNOSIS....4264
STEP 1. Using scan tool (M.U.T.-III), Check the configuration function.....4264
STEP 2. Using scan tool (M.U.T.-III), read the ETACS-ECU diagnostic trouble code.....4265
STEP 3. Check that the turn-signal light operate.....4265
STEP 4. Replace the ECU.....4265
Inspection Procedure B-3: The turn-signal indicator lights do not illuminate.....4265
DIAGNOSIS....4265
STEP 1. Check turn-signal light....4265
STEP 2. Using scan tool (M.U.T.-III), diagnose the CAN bus line....4265
STEP 3. Using scan tool (M.U.T.-III), read the diagnostic trouble code.....4265
STEP 4. Check by scan tool (M.U.T.-III) 'Special Function'....4266
Inspection Procedure B-4: One of the turn-signal lights does not illuminate.....4266
DIAGNOSIS....4266
STEP 1. Confirm which turn-signal light is defective.....4266
STEP 2. Resistance measurement at the side turn-signal light connector.....4267
STEP 3. Check of open circuit in ground line between side turn-signal light connector <Fender mirror type>, door mirror assembly <Door mirror type> and ground.....4267
STEP 4. Check of open circuit in TURN LH or TURN RH line between side turn-signal light connector <Fender mirror type>, door mirror assembly connector <Door mirror type> and ETACS-ECU connector.....4267
STEP 5. Retest the system.....4268
ON-VEHICLE SERVICE....4268
HEADLIGHT AIMING....4268
PRE-AIMING INSTRUCTIONS (LOW-BEAM)....4268
HEADLIGHT ADJUSTMENT (LOW-BEAM)....4269
LUMINOUS INTENSITY MEASUREMENT....4270
BULB REPLACEMENT....4270
HEADLIGHT BULB REPLACEMENT....4270
POSITION LIGHT BULB REPLACEMENT....4271
FRONT TURN-SIGNAL LIGHT BULB REPLACEMENT....4271
FRONT SIDE-MARKER LIGHT BULB REPLACEMENT....4271
HEADLIGHT AUTOMATIC-SHUTDOWN FUNCTION CHECK....4272
HEADLIGHT....4273
INSPECTION....4274
HEADLIGHT RELAY CHECK....4274
REAR COMBINATION LIGHT....4275
DIAGNOSIS....4277
SYMPTOM PROCEDURES....4277
Inspection Procedure 1: None of the taillights illuminate.....4277
DIAGNOSIS....4278
STEP 1. Using scan tool (M.U.T.-III), read the diagnostic trouble code....4278
STEP 2. Using scan tool (M.U.T.-III), check data list....4278
STEP 3. Retest the system....4278
Inspection Procedure 2: One of taillights does not illuminate.....4278
DIAGNOSIS....4278
STEP 1. Check the bulbs of the taillights.....4278
STEP 2. Resistance measurement at the rear combination light (taillight: LH) connector or rear combination light (taillight: RH) connector.....4279
STEP 3. Check of open circuit in ground line between the rear combination light (taillight: LH) connector or rear combination light (taillight: RH) connector (ground terminal) and ground.....4279
STEP 4. Check of open circuit in TAIL LP lines between the rear combination light (taillight: LH) connector or rear combination light (taillight: RH) connector and ETACS-ECU connector.....4279
STEP 5. Retest the system.....4279
Inspection Procedure 3: The back-up light do not illuminate normally.....4279
DIAGNOSIS....4280
STEP 1. Check the operation of the position lights and the headlights.....4280
STEP 2. Check the transmission range switch <CVT> or back-up light switch <M/T>.....4280
STEP 3. Voltage measurement at the transmission range switch connector <CVT> or back-up light switch connector <M/T>.....4280
STEP 4. Check of open circuit in power supply line between the transmission range switch connector <CVT> or back-up light switch connector <M/T> and the ignition switch (IG1).....4281
STEP 5. Check the bulb of the back-up light....4281
STEP 6. Resistance measurement at the rear combination light (back-up light) connector....4281
STEP 7. Check of open circuit in ground line between rear combination light (back-up light) connector and ground.....4281
STEP 8. Check of open circuit in output line between the rear combination light (back-up light) connector and back-up light switch connector.....4281
STEP 9. Retest the system....4281
Inspection Procedure 4: The stoplight do not illuminate or go out normally.....4282
DIAGNOSIS....4282
STEP 1. Using scan tool (M.U.T.-III), check data list....4282
STEP 2. Voltage measurement at the joint connector....4282
STEP 3. Check of short to power supply, and open circuit in power supply line between the joint connector and the fusible link.....4282
STEP 4. Resistance measurement at the liftgate spoiler connector <high-mounted stoplight>, rear combination light (stop: LH) connector, rear combination light (stop: RH) connector....4282
STEP 5. Check the following wiring harness....4283
STEP 6. Check the following wiring harness....4283
STEP 7. Retest the system....4283
ON-VEHICLE SERVICE....4283
REPLACE THE BULB....4283
REAR TURN-SIGNAL LIGHT BULB REPLACEMENT....4283
STOPLIGHT/TAILLIGHT/REAR SIDE-MARKER LIGHT BULB REPLACEMENT....4283
BACK-UP LIGHT BULB REPLACEMENT....4284
FRONT FOG LIGHT....4285
DIAGNOSIS....4288
SYMPTOM PROCEDURES....4288
Inspection Procedure 1: The front fog lights do not illuminate normally.....4288
DIAGNOSIS....4289
STEP 1. ETACS-ECU coding data check....4289
STEP 2. Check the operation of the headlights.....4289
STEP 3. Using scan tool (M.U.T.-III), read the other system diagnostic trouble code....4289
STEP 4. Using scan tool (M.U.T.-III), check data list.....4289
STEP 5. Check the front fog light relay....4289
STEP 6. Voltage measurement at the front fog light relay connector....4289
STEP 7. Check of short to power supply, and open circuit in power supply lines between front fog light relay connector and the fusible link.....4290
STEP 8. Check of short to power supply, and open circuit in FOGY line between front fog light relay connector and the ETACS-ECU connector.....4290
STEP 9. Check of short to power supply, and open circuit in output lines between front fog light relay connector and the front fog light (LH) or front fog light (RH) connector.....4290
STEP 10. Check of open circuit in ground lines between the front fog light (LH) or front fog light (RH) connector and ground.....4290
STEP 11. Retest the system....4290
Inspection Procedure 2: One of the front fog lights does not illuminate normally.....4290
DIAGNOSIS....4290
STEP 1. Bulb check....4290
STEP 2. Resistance measurement at the front fog light (LH) connector or front fog light (RH) connector....4290
STEP 3. Check of open circuit in ground lines between the front fog light (LH) connector or front fog light (RH) connector and ground.....4290
STEP 4. Check of short to power supply, and open circuit in output lines between front fog light relay connector and the front fog light (LH) or front fog light (RH) connector.....4291
STEP 5. Retest the system....4291
Inspection Procedure 3: The front fog light indicator does not illuminate normally.....4291
DIAGNOSIS....4291
STEP 1. Check the front fog lights....4291
STEP 2. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....4291
STEP 3. Using scan tool (M.U.T.-III), read the ETACS diagnostic trouble code.....4291
STEP 4. Check by scan tool (M.U.T.-III) 'Special Function'....4291
ON-VEHICLE SERVICE....4292
FRONT FOG LIGHT AIMING....4292
PRE-AIMING INSTRUCTIONS....4292
FRONT FOG LIGHT ADJUSTMENT....4293
REPLACE THE BULB....4293
INSPECTION....4295
FRONT FOG LIGHT RELAY CHECK....4295
SIDE TURN-SIGNAL LIGHT....4296
<DOOR MIRROR TYPE>....4296
REMOVAL SERVICE POINT....4296
INSTALLATION SERVICE POINT....4297
DOME LIGHT....4298
DIAGNOSIS....4300
SYMPTOM PROCEDURES....4300
Inspection Procedure 1: The dome light does not illuminate normally.....4300
DIAGNOSIS....4301
STEP 1. Retest the system.....4301
STEP 2. Dome light bulb check....4301
STEP 3. Check of open circuit in power supply lines between the dome light connector and the fusible link.....4301
STEP 4. Check of open circuit in ground line between the dome light connector and the ground.....4301
STEP 5. Retest the system....4301
STEP 6. Using scan tool (M.U.T.-III), check data list.....4302
STEP 7. Check of open circuit in ROOM LP lines between the dome light connector and the ETACS-ECU connector.....4302
STEP 8. Retest the system....4302
Inspection Procedure 2: The luggage compartment light does not illuminate normally.....4302
DIAGNOSIS....4303
STEP 1. Dome light operation check....4303
STEP 2. Luggage compartment light bulb check....4303
STEP 3. Check of open circuit in power supply lines between the luggage compartment light connector and the fusible link.....4303
STEP 4. Check of open circuit in ROOM lines between the luggage compartment light connector and the ETACS-ECU connector.....4303
STEP 5. Retest the system....4303
Inspection Procedure 3: The interior light automatic shutoff function does not work normally.....4303
DIAGNOSIS....4304
STEP 1. Using scan tool (M.U.T.-III), Check the configuration function....4304
STEP 2. Using scan tool (M.U.T.-III), read the diagnostic trouble code.....4304
STEP 3. Using scan tool (M.U.T.-III), check data list....4304
STEP 4. Retest the system....4304
ON-VEHICLE SERVICE....4304
REMOVAL SERVICE POINT....4307
HIGH-MOUNTED STOPLIGHT....4307
LICENSE PLATE LIGHT....4308
DIAGNOSIS....4308
SYMPTOM PROCEDURES....4308
Inspection Procedure 1: The license plate lights do not illuminate.....4308
DIAGNOSIS....4308
STEP 1. Operation check of rear combination light (taillight, LH)....4308
STEP 2. Resistance measurement at license plate light connector....4309
STEP 3. Check of open circuit in ground line between license plate light connector and ground.....4309
STEP 4. Check of open circuit in power supply lines between the license plate light connector and joint connector.....4309
Inspection Procedure 2: One of the license plate lights does not illuminate.....4309
DIAGNOSIS....4309
STEP 1. Bulb check....4309
STEP 2. Retest the system.....4310
HAZARD WARNING LIGHT SWITCH....4311
DIAGNOSIS....4313
SYMPTOM PROCEDURES....4313
Inspection Procedure 1: The hazard warning lights do not illuminate.....4313
DIAGNOSIS....4314
STEP 1. Check that the turn-signal lights operate.....4314
STEP 2. Using scan tool (M.U.T.-III), read the diagnostic trouble code.....4314
STEP 3. Using scan tool (M.U.T.-III), check data list....4314
STEP 4. Retest the system.....4314
INSPECTION....4315
CONTINUITY CHECK FOR HAZARD WARNING LIGHT SWITCH....4315
HORN....4316
INSTALLATION SERVICE POINT....4316
INSPECTION....4317
HORN RELAY CHECK....4317
REAR VIEW CAMERA....4317
DIAGNOSIS....4318
SYMPTOM PROCEDURES....4318
Rear view camera image is not correctly displayed.....4318
DIAGNOSIS....4318
STEP 1. Self-connection check by MMES....4318
STEP 2. Resistance measurement at rear view camera connector (ground terminal)....4319
STEP 3. Check of open circuit in ground line between rear view camera connector and the ground....4319
STEP 4. Check of short to power supply, short to ground, and open circuit in CACC, CMP-, CMP+ line between multivision display connector and rear view camera connector....4319
STEP 5. Check the back-up light switch <M/T> or transmission range switch <CVT>.....4319
STEP 6. Check of short to power supply, short to ground, and open circuit in REV line between multivision display connector and back-up light switch <M/T> or transmission range switch <CVT> connector....4319
STEP 7. Trouble symptom recheck....4319
STEP 8. Trouble symptom recheck....4319
ACCESSORY SOCKET....4321
COLUMN SWITCH....4322
DIAGNOSIS....4324
HOW TO CONNECT THE SCAN TOOL (M.U.T.-III)....4324
HOW TO READ AND ERASE DIAGNOSTIC TROUBLE CODES....4325
DIAGNOSTIC TROUBLE CODE PROCEDURES....4326
DTC B1763: Lighting switch DTC B1764: Wiper switch....4326
DIAGNOSIS....4326
STEP 1. Using scan tool (M.U.T.-III), Check whether the diagnostic trouble code is set again.....4326
STEP 2. Using scan tool (M.U.T.-III), Check whether the diagnostic trouble code is set again.....4327
REMOVAL SERVICE POINTS....4328
INSTALLATION SERVICE POINT....4328
INSPECTION....4329
RADIO AND CD PLAYER....4329
DIAGNOSIS....4330
SYMPTOM PROCEDURES....4331
Inspection Procedure 1: Power is not turned ON when the power switch is turned ON.....4331
DIAGNOSIS....4331
STEP 1. Voltage measurement at radio and CD player connector (ACC terminal)....4332
STEP 2. Check of short to power supply, short to ground, and open circuit in ACC line between ignition switch (ACC) and radio and CD player connector....4332
STEP 3. Using scan tool (M.U.T.-III), read the KOS diagnostic trouble code....4332
STEP 4. Check of short to power supply, short to ground, and open circuit in ACC line between ACC relay and radio and CD player connector....4332
STEP 5. Voltage measurement at radio and CD player connector (+B terminal)....4332
STEP 6. Check of short to power supply, short to ground, and open circuit in +B line between fusible link and radio and CD player connector....4332
STEP 7. Check of short to open circuit in GND line between radio and CD player connector and ground....4332
STEP 8. Retest the system....4332
Inspection Procedure 2: No sound is heard.....4333
DIAGNOSIS....4333
STEP 1. Checking with audio speaker test....4333
STEP 2. Check the speaker.....4333
STEP 3. Check the wiring harness between the speaker connector terminal and the radio and CD player connector terminal.....4334
STEP 4. Check the speaker.....4334
STEP 5. Check the wiring harness between the speaker connector terminal and the radio and CD player connector terminal.....4335
STEP 6. Retest the system....4335
Inspection Procedure 3: The radio broadcasting can not be received.....4335
DIAGNOSIS....4335
STEP 1. Check the state of the antenna rod and antenna base.....4335
STEP 2. Check to see if inspections are taking place is an area exposed to special electric fields.....4336
STEP 3. Move the vehicle and check the radio.....4336
STEP 4. Check if there is any damage to the antenna rod, antenna base and antenna feeder.....4336
STEP 5. Check the connection of the antenna feeder’s plug and radio and CD player.....4336
STEP 6. Substitute a known good radio and CD player, and check the trouble symptom.....4336
Inspection Procedure 4: Audio illuminations does not work normally.....4336
DIAGNOSIS....4336
STEP 1. Check that the taillights illuminate.....4336
STEP 2. Check of short to power supply, short to ground, and open circuit in ILL+ line between radio and CD player connector and ETACS-ECU (taillight relay)....4336
STEP 3. Combination meter check....4336
STEP 4. Substitute the ETACS-ECU with good one, and check the trouble symptom.....4337
Inspection Procedure 5: An audio file, which is stored in the USB memory/iPod, cannot be played.....4337
DIAGNOSIS....4337
STEP 1. Check if the error message is displayed on the monitor.....4337
STEP 2. Check the USB cable.....4337
STEP 3. Retest the system....4337
Inspection Procedure 6: An audio file, which is connected through the external input (AUX) terminal, cannot be played.....4337
<Vehicles with hands free-ECU>....4338
MMES....4340
DIAGNOSIS....4340
PRIOR TO DISCONNECTING THE VEHICLE BATTERY....4340
DIAGNOSIS TIPS CONCERNING THE NAVIGATION FUNCTION....4341
SYMPTOM PROCEDURES....4343
Inspection Procedure 1: Power is not turned ON when the power switch is turned ON.....4343
DIAGNOSIS....4344
STEP 1. Voltage measurement at multivision display connector (ACC terminal)....4344
STEP 2. Check of short to power supply, short to ground, and open circuit in ACC line between ignition switch (ACC) and multivision display connector....4344
STEP 3. Using scan tool (M.U.T.-III), read the KOS diagnostic trouble code....4344
STEP 4. Check of short to power supply, short to ground, and open circuit in ACC line between ACC relay and multivision display connector....4344
STEP 5. Voltage measurement at multivision display connector (+B terminal)....4344
STEP 6. Check of short to power supply, short to ground, and open circuit in +B line between fusible link and multivision display connector....4344
STEP 7. Resistance measurement at multivision display connector (GND terminal)....4344
STEP 8. Check of open circuit in GND line between multivision display connector and ground....4345
STEP 9. Retest the system....4345
Inspection Procedure 2: Current location is not displayed correctly.....4345
DIAGNOSIS....4345
STEP 1. Self-connection check by MMES....4345
STEP 2. Check the GPS antenna.....4345
STEP 3. Check of short to power supply, short to ground, and open circuit in SPD line between multivision display connector and combination meter connector....4346
STEP 4. Check the signal reception state of the GPS antenna.....4346
STEP 5. Reset the MMES and check the trouble symptom.....4346
Inspection Procedure 3: No sound is heard.....4346
DIAGNOSIS....4347
STEP 1. Check a trouble spot.....4347
STEP 2. Check the multivision display operation.....4347
STEP 3. Check the speaker.....4347
STEP 4. Check the wiring harness between the speaker connector terminal and the multivision display connector terminal.....4348
STEP 5. Check the speaker.....4348
STEP 6. Check the wiring harness between the speaker connector terminal and the multivision display connector terminal.....4349
STEP 7. Retest the system....4349
Inspection Procedure 4: The radio broadcasting can not be received.....4349
DIAGNOSIS....4349
STEP 1. Check the state of the antenna rod and antenna base.....4349
STEP 2. Check to see if inspections are taking place is an area exposed to special electric fields.....4349
STEP 3. Move the vehicle and check the radio.....4350
STEP 4. Check if there is any damage to the antenna rod, antenna base and antenna feeder.....4350
STEP 5. Check the connection of the antenna feeder’s plug and multivision display.....4350
STEP 6. Substitute a known good multivision display, and check the trouble symptom.....4350
Inspection Procedure 5: CD/DVD cannot be played.....4350
DIAGNOSIS....4350
STEP 1. Check if the error message is displayed on the monitor.....4350
STEP 2. Check the CD/DVD insertion surface.....4350
STEP 3. Check the CD/DVD.....4350
STEP 4. Check the CD/DVD.....4350
STEP 5. Temporarily replace the CD /DVD with another CD or DVD, and check the trouble symptom.....4350
STEP 6. Temporarily replace the multivision display, and check the trouble symptom.....4351
Inspection Procedure 6: An audio file, which is stored in the USB memory/iPod, cannot be played.....4351
DIAGNOSIS....4351
STEP 1. Check whether the iPod is supported.....4351
STEP 2. Check if the error message is displayed on the monitor.....4351
STEP 3. Check the USB cable.....4351
STEP 4. Retest the system....4352
Inspection Procedure 7: An audio file, which is stored in the SD memory card, cannot be played.....4352
DIAGNOSIS....4352
STEP 1. Check if the error message is displayed on the monitor.....4352
STEP 2. Retest the system....4352
Inspection Procedure 8: The hands-free cellular phone system does not operate normally.....4353
DIAGNOSIS....4353
STEP 1. Check whether the Bluetooth‚ device is supported.....4353
STEP 2. Reset the MMES and check the trouble symptom.....4353
Inspection Procedure 9: The screen brightness is not changed in conjunction with the taillights.....4353
DIAGNOSIS....4353
STEP 1. Self-connection check by MMES....4354
STEP 2. Check of short to power supply, short to ground, and open circuit in ILL+ line between multivision display connector and ETACS-ECU (taillight relay)....4354
STEP 3. Retest the system....4354
ON-VEHICLE SERVICE....4354
CONNECTION CHECK FUNCTION....4354
How to check connections....4354
PAIRING THE BLUETOOTH‚ DEVICE....4356
How to activate or deactivate the pairing with a Bluetooth‚ device through the multivision display....4356
How to pair....4356
How to deactivate or activate the paring....4357
HOW TO RESET MMES....4358
How to reset....4358
INSTALLATION SERVICE POINT....4361
STEERING WHEEL AUDIO REMOTE CONTROL SWITCH....4362
DIAGNOSIS....4362
SYMPTOM PROCEDURES....4363
Inspection Procedure 1: Steering wheel remote control switch (audio remote control switch) does not function.....4363
DIAGNOSIS....4363
STEP 1. Check the steering wheel remote control switch.....4363
STEP 2. Check the clock spring.....4363
STEP 3. Check of short to power supply, short to ground, and open circuit in REM+, REM- line between radio and CD player connector or multivision display connector and steering wheel remote control switch connector....4364
STEP 4. Retest the system....4364
Inspection Procedure 2: Steering wheel remote control switch illumination does not come on.....4364
DIAGNOSIS....4364
STEP 1. Check the steering wheel remote control switch.....4365
STEP 2. Resistance measurement at steering wheel remote control switch connector (ground terminal)....4365
STEP 3. Check of open circuit in ground line between steering wheel remote control switch connector and the ground....4365
STEP 4. Check the clock spring.....4365
STEP 5. Check of short to power supply, short to ground, and open circuit in ILL+ line between combination meter connector and steering wheel remote control switch connector....4365
STEP 6. Retest the system....4366
STEERING WHEEL AUDIO REMOTE CONTROL SWITCH....4366
STEERING WHEEL AUDIO REMOTE CONTROL SWITCH CHECK....4366
ILLUMINATION CHECK....4366
HANDS-FREE INTERFACE SYSTEM <VEHICLES WITH HANDS FREE-ECU>....4367
MMCS DIAGNOSIS....4367
STANDARD FLOW OF DIAGNOSTIC TROUBLESHOOTING....4369
DIAGNOSIS MODE....4369
SYMPTOM PROCEDURES....4372
Inspection Procedure 1: Check the hands free-ECU power supply circuit.....4372
DIAGNOSIS....4372
STEP 1. Resistance measurement at hands free-ECU connector (GND terminal).....4372
STEP 2. Check of open circuit in GND line between hands free-ECU connector and ground.....4372
STEP 3. Voltage measurement at hands free-ECU connector (+B terminal).....4373
STEP 4. Check of short to power supply, short to ground, and open circuit in +B line between fusible link and hands free-ECU connector.....4373
STEP 5. Voltage measurement at hands free-ECU connector (ACC terminal).....4373
STEP 6. Check of short to power supply, short to ground, and open circuit in ACC line between hands free-ECU connector and radio and CD player connector.....4373
Inspection Procedure 2: The USB data cannot be replayed.....4373
DIAGNOSIS....4374
STEP 1. Check the radio and CD player operation.....4374
STEP 2. Check the diagnosis mode....4374
STEP 3. Check the USB cable.....4374
STEP 4. Check of short to power supply, short to ground, and open circuit in AAL+, AAR+ line between hands free-ECU connector and radio and CD player connector.....4374
STEP 5. Replace the hands free-ECU temporarily, and check the trouble symptom.....4375
Inspection Procedure 3: When the speech switch is pressed, the voice guide is output, but the voice recognition is not performed.....4375
DIAGNOSIS....4375
STEP 1. Retest the system....4375
STEP 2. Check the diagnosis mode....4376
STEP 3. Check of short to power supply, short to ground, and open circuit in MIC+, MIC- line between hands free-ECU connector and microphone unit connector.....4376
STEP 4. Replace the microphone unit temporarily, and check the trouble symptom.....4376
STEP 5. Replace the hands free-ECU temporarily, and check the trouble symptom.....4376
Inspection Procedure 4: When the speech switch is pressed, the voice guide is not output.....4376
DIAGNOSIS....4377
STEP 1. Check the diagnosis mode....4377
STEP 2. Operation check of the steering wheel remote control switch (audio remote control switch)....4377
STEP 3. Check the steering wheel remote control switch (speech switch).....4377
STEP 4. Temporarily replace the hands free-ECU, and check the trouble symptom.....4377
Inspection Procedure 5: DIAGNOSIS MODE cannot be made an entry. Mobile Phone item is not displayed on the MENU screen of audio.....4377
DIAGNOSIS....4378
STEP 1. Check the radio and CD player operation.....4378
STEP 2. Check of short to power supply, short to ground, and open circuit in IE+, IE- line between hands free-ECU connector and radio and CD player connector.....4378
STEP 3. Check if the power supply circuit of hands free-ECU have a problem.....4378
STEP 4. Replace the hands free-ECU temporarily, and check the trouble symptom.....4378
Inspection Procedure 6: Voice guide 'Unable to obtain vehicle speed. Please try again or contact your dealer for service' is sent from the speaker....4379
DIAGNOSIS....4379
STEP 1. Check the radio and CD player operation.....4379
STEP 2. Check the diagnosis mode....4379
STEP 3. Replace the hands free-ECU temporarily, and check the trouble symptom.....4379
ON-VEHICLE SERVICE....4380
PAIRING METHOD....4380
PAIRING DELETION METHOD....4381
HANDS FREE ECU....4382
MICROPHONE UNIT....4383
REMOVAL AND INSTALLATION....4383
REMOVAL SERVICE POINT....4383
INSTALLATION SERVICE POINT....4383
STEERING WHEEL VOICE CONTROL SWITCH....4383
REMOVAL AND INSTALLATION....4383
STEERING WHEEL VOICE CONTROL SWITCH CHECK....4384
ILLUMINATION CHECK....4384
SPEAKER....4384
ON-VEHICLE SERVICE....4384
SPEAKER TEST <VEHICLES WITH RADIO AND CD PLAYER>....4384
SPEAKER CONNECTION CHECK MODE....4384
REMOVAL SERVICE POINT....4386
ANTENNA....4387
ETACS....4388
DIAGNOSIS....4390
HOW TO CONNECT THE SCAN TOOL (M.U.T.-III)....4390
HOW TO READ AND ERASE DIAGNOSTIC TROUBLE CODES....4391
HOW TO DIAGNOSE THE CAN BUS LINES....4392
CHECK OF FREEZE FRAME DATA....4392
DIAGNOSTIC TROUBLE CODE PROCEDURES....4394
DTC B1709: ETACS ECU (EEPROM)....4394
DTC B1760: Coding not completed....4394
DTC B1761: VIN not programmed....4395
DIAGNOSIS....4395
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....4395
STEP 2. Write the VIN.....4395
DTC B1762: IOD fuse not seated fully DTC B1765: ECU fuse....4396
DIAGNOSIS....4396
STEP 1. Check the power supply fuses (fuse Nos. 25 and 26)....4396
STEP 2. Check of short to power supply, short to ground, and open circuit in ETACS +B line between fusible link and ETACS-ECU connector....4396
STEP 3. Using scan tool (M.U.T.-III), read the KOS diagnostic trouble code....4397
STEP 4. Check of short to power supply, short to ground, and open circuit in ACCI line between ignition switch (ACC) <vehicles without KOS> or ACC relay connector <vehicles with KOS> and ETACS-ECU connector....4397
STEP 5. Recheck for diagnostic trouble code.....4397
DTC B2206: VIN error/Mismatch....4397
DIAGNOSIS....4398
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....4398
STEP 2. Using scan tool (M.U.T.-III), read the engine control module diagnostic trouble code....4398
STEP 3. Recheck for diagnostic trouble code.....4398
DTC U1000: OSS CAN timeout....4398
DIAGNOSIS....4398
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line....4398
STEP 2. Using scan tool (M.U.T.-III), read the KOS diagnostic trouble code....4399
STEP 3. Using scan tool (M.U.T.-III), read the combination meter diagnostic trouble code....4399
STEP 4. Recheck for diagnostic trouble code.....4399
STEP 5. Recheck for diagnostic trouble code.....4399
STEP 6. Recheck for diagnostic trouble code.....4399
DTC U1100: Engine CAN timeout....4399
DIAGNOSIS....4400
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....4400
STEP 2. Using scan tool (M.U.T.-III), read the engine control module diagnostic trouble code....4400
STEP 3. Using scan tool (M.U.T.-III), read the combination meter diagnostic trouble code....4400
STEP 4. Recheck for diagnostic trouble code.....4400
STEP 5. Recheck for diagnostic trouble code.....4400
STEP 6. Recheck for diagnostic trouble code.....4400
DTC U1101: T/M CAN timeout/Not equipped....4401
DIAGNOSIS....4401
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line....4401
STEP 2. Using scan tool (M.U.T.-III), read the CVT diagnostic trouble code....4401
STEP 3. Using scan tool (M.U.T.-III), read the combination meter diagnostic trouble code....4401
STEP 4. Recheck for diagnostic trouble code.....4401
STEP 5. Recheck for diagnostic trouble code.....4401
STEP 6. Recheck for diagnostic trouble code.....4402
DTC U1102: ASC/TCL/ABS timeout/Not equipped....4402
DIAGNOSIS....4402
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line....4402
STEP 2. Using scan tool (M.U.T.-III), read the ASC diagnostic trouble code....4402
STEP 3. Using scan tool (M.U.T.-III), read the SRS diagnostic trouble code....4402
STEP 4. Recheck for diagnostic trouble code.....4402
STEP 5. Recheck for diagnostic trouble code.....4403
STEP 6. Recheck for diagnostic trouble code.....4403
DTC U1108: Meter CAN timeout/Not equipped....4403
DIAGNOSIS....4403
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....4403
STEP 2. Using scan tool (M.U.T.-III), read the combination meter diagnostic trouble code....4403
STEP 3. Using scan tool (M.U.T.-III), read the SRS diagnostic trouble code....4404
STEP 4. Recheck for diagnostic trouble code.....4404
STEP 5. Recheck for diagnostic trouble code.....4404
STEP 6. Recheck for diagnostic trouble code.....4404
DTC U1110: A/C CAN timeout/Not equipped....4404
DIAGNOSIS....4405
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line....4405
STEP 2. Using scan tool (M.U.T.-III), read the A/C diagnostic trouble code....4405
STEP 3. Recheck for diagnostic trouble code.....4405
STEP 4. Recheck for diagnostic trouble code.....4405
STEP 5. Recheck for diagnostic trouble code.....4405
DTC U1116: F.A.S.T. CAN timeout/No equipped....4406
DIAGNOSIS....4406
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....4406
STEP 2. Using scan tool (M.U.T.-III), read the KOS diagnostic trouble code....4406
STEP 3. Using scan tool (M.U.T.-III), read the combination meter diagnostic trouble code....4406
STEP 4. Recheck for diagnostic trouble code.....4406
STEP 5. Recheck for diagnostic trouble code.....4406
STEP 6. Recheck for diagnostic trouble code.....4407
DTC U1150: Fail Info. for vehicle speed....4407
DIAGNOSIS....4407
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line....4407
STEP 2. Using scan tool (M.U.T.-III), read the engine control module diagnostic trouble code....4407
STEP 3. Recheck for diagnostic trouble code.....4407
STEP 4. Recheck for diagnostic trouble code.....4408
STEP 5. Recheck for diagnostic trouble code.....4408
SERVICE DATA REFERENCE TABLE....4408
SYMPTOM PROCEDURES....4412
Inspection Procedure A-1: Check the battery power supply circuit to the ETACS-ECU.....4412
DIAGNOSIS....4412
STEP 1. Resistance measurement at ETACS-ECU connector (EARTH, SGND terminal)....4412
STEP 2. Check of open circuit in EARTH, SGND line between ETACS-ECU connector and ground....4412
STEP 3. Voltage measurement at ETACS-ECU connector (ETACS +B terminal)....4413
STEP 4. Check of short to power supply, short to ground, and open circuit in ETACS +B line between fusible link and ETACS-ECU connector....4413
STEP 5. Retest the system.....4413
Inspection procedure B-1: Light reminder tone alarm does not work normally.....4413
DIAGNOSIS....4414
STEP 1. Using scan tool (M.U.T.-III), read the diagnostic trouble code.....4414
STEP 2. Using scan tool (M.U.T.-III), check data list....4414
STEP 3. Check by scan tool (M.U.T.-III) 'Special Function'....4414
STEP 4. Retest the system.....4414
INPUT SIGNAL PROCEDURES....4415
Inspection Procedure 1: The ignition switch (ACC) signal is not received.....4415
DIAGNOSIS....4415
STEP 1. Voltage measurement at ETACS-ECU connector (ACCI terminal)....4415
STEP 2. Check of short to power supply, short to ground, and open circuit in ACCI line between ignition switch (ACC) and ETACS-ECU connector....4415
STEP 3. Using scan tool (M.U.T.-III), read the KOS diagnostic trouble code....4416
STEP 4. Check of short to power supply, short to ground, and open circuit in ACCI line between ACC relay connector and ETACS-ECU connector....4416
STEP 5. Using scan tool (M.U.T.-III), check data list.....4416
Inspection Procedure 2: The ignition switch (IG1) signal is not received.....4416
DIAGNOSIS....4416
STEP 1. Voltage measurement at ETACS-ECU connector (IG1 terminal)....4416
STEP 2. Check of short to power supply, short to ground, and open circuit in IG1 line between ignition switch (IG1) and ETACS-ECU connector....4417
STEP 3. Using scan tool (M.U.T.-III), read the KOS diagnostic trouble code....4417
STEP 4. Check of short to power supply, short to ground, and open circuit in IG1 line between IG1 relay connector and ETACS-ECU connector....4417
STEP 5. Using scan tool (M.U.T.-III), check data list.....4417
Inspection Procedure 3: The key reminder switch signal is not received.....4417
DIAGNOSIS....4417
STEP 1. Check the key reminder switch.....4417
STEP 2. Resistance measurement at key reminder switch connector (ground terminal)....4418
STEP 3. Check of open circuit in ground line between key reminder switch connector and the ground....4418
STEP 4. Check of short to power supply, short to ground, and open circuit in HL1+ line between ETACS-ECU connector and key reminder switch connector....4418
STEP 5. Using scan tool (M.U.T.-III), check data list.....4418
Inspection Procedure 4: The front door lock actuator (driver’s side) signal is not received.....4418
DIAGNOSIS....4418
STEP 1. Front door lock actuator (driver’s side) check....4419
STEP 2. Resistance measurement at front door lock actuator (RH) connector (ground terminal)....4419
STEP 3. Check of open circuit in ground line between front door lock actuator (RH) connector and ground....4419
STEP 4. Check of short to power supply, short to ground, and open circuit in DSWL, DSWU line between ETACS-ECU connector and front door lock actuator (RH) connector....4419
STEP 5. Using scan tool (M.U.T.-III), check data list.....4419
Inspection Procedure 5: The front door switch (driver’s side) signal is not received.....4419
DIAGNOSIS....4419
STEP 1. Check the installation condition.....4420
STEP 2. Front door switch (driver’s side) check....4420
STEP 3. Check of short to power supply, short to ground, and open circuit in DDSW line between ETACS-ECU connector and front d....4420
STEP 4. Using scan tool (M.U.T.-III), check data list.....4420
Inspection Procedure 6: The front door switch (passenger’s side) signal is not received.....4420
DIAGNOSIS....4420
STEP 1. Check the installation condition.....4420
STEP 2. Front door switch (passenger’s side) check....4420
STEP 3. Check of short to power supply, short to ground, and open circuit in ADSW line between ETACS-ECU connector and front d....4420
STEP 4. M.U.T.-III data list....4421
Inspection procedure 7: One of the door switch signals (including the liftgate latch switch) is not received.....4421
DIAGNOSIS....4421
STEP 1. Using scan tool (M.U.T.-III), check data list.....4422
STEP 2. Check the installation condition.....4422
STEP 3. Check the rear door switches or the liftgate latch switch.....4422
STEP 4. Check the wiring harness between each rear door switch connector or the liftgate latch switch connector and the ETACS-ECU connector.....4422
STEP 5. Connector check: ETACS-ECU connector (DOOR terminal)....4423
STEP 6. Using scan tool (M.U.T.-III), check data list.....4423
Inspection Procedure 8: The hazard warning light switch signal is not received.....4423
DIAGNOSIS....4423
STEP 1. Check the hazard warning light switch.....4423
STEP 2. Resistance measurement at hazard warning switch connector (ground terminal)....4423
STEP 3. Check of open circuit in ground line between hazard warning switch connector and ground....4423
STEP 4. Check of short to power supply, short to ground, and open circuit in HAZ line between ETACS-ECU connector and hazard warning switch connector....4424
STEP 5. Using scan tool (M.U.T.-III), check data list.....4424
Inspection Procedure 9: The column switch signal is not received.....4424
DIAGNOSIS....4424
STEP 1. Using scan tool (M.U.T.-III), read the ETACS diagnostic trouble code....4424
Inspection Procedure 10: The stoplight switch signal is not received.....4425
DIAGNOSIS....4425
STEP 1. Check the stoplight switch.....4425
STEP 2. Voltage measurement at stoplight switch connector (power supply terminal)....4425
STEP 3. Check of short to power supply, short to ground, and open circuit in power supply line between stoplight switch connector and fusible link....4425
STEP 4. Check of short to power supply, short to ground, and open circuit in BKLP line between ETACS-ECU connector and stoplight switch connector....4425
STEP 5. Using scan tool (M.U.T.-III), check data list.....4425
Inspection Procedure 11: The rear window defogger switch signal is not received. <vehicles with manual air conditioning>....4426
DIAGNOSIS....4426
STEP 1. Check the rear window defogger switch.....4426
STEP 2. Resistance measurement at heater control panel connector (ground terminal)....4426
STEP 3. Check of open circuit in ground line between heater control panel connector and ground....4426
STEP 4. Check of short to power supply, short to ground, and open circuit in DFSW line between ETACS-ECU connector and heater control panel connector....4426
STEP 5. Using scan tool (M.U.T.-III), check data list.....4426
Inspection Procedure 12: The rear window defogger switch signal is not received. <vehicles with automatic air conditioning>....4427
DIAGNOSIS....4427
STEP 1. Using scan tool (M.U.T.-III), check other systems data list.....4427
STEP 2. Check of short to power supply, short to ground, and open circuit in DFSW line between ETACS-ECU connector and auto A/C controller assembly (A/C-ECU) connector....4427
STEP 3. Using scan tool (M.U.T.-III), check data list.....4427
ON-VEHICLE SERVICE....4431
ETACS-ECU....4435
PANIC ALARM....4436
DIAGNOSIS....4436
SYMPTOM PROCEDURES....4436
Panic alarm does not work normally.....4436
DIAGNOSIS....4436
STEP 1. Check keyless entry system <vehicles without KOS> or keyless operation system <vehicles with KOS>.....4436
STEP 2. Check that the headlight operate.....4437
STEP 3. Check of short to power supply, short to ground, and open circuit in DHOR line between horn relay connector and ETACS-ECU connector....4437
STEP 4. Retest the system.....4437
DEFOGGER....4438
DIAGNOSIS....4440
SYMPTOM PROCEDURES....4441
The rear window defogger does not work. <vehicles with manual air conditioning>....4441
DIAGNOSIS....4441
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line....4441
STEP 2. Using scan tool (M.U.T.-III), read the ETACS diagnostic trouble code.....4441
STEP 3. Using scan tool (M.U.T.-III), read the engine control module diagnostic trouble code....4441
STEP 4. Using scan tool (M.U.T.-III), check data list....4441
STEP 5. Check the rear window defogger relay.....4441
STEP 6. Voltage measurement at the rear window defogger connector.....4442
STEP 7. Resistance measurement at the rear window defogger connector.....4442
STEP 8. Voltage measurement at the rear window defogger relay connector.....4442
STEP 9. Check of short to power supply, and open circuit in power supply line between rear window defogger relay connector and fusible link.....4442
STEP 10. Voltage measurement at the rear window defogger relay connector.....4442
STEP 11. Check of short to power supply, and open circuit in input line between rear window defogger relay connector and ignition switch (IG2).....4442
STEP 12. Check of short to power supply, and open circuit in DEF1 line between rear window defogger relay connector and ETACS-ECU.....4442
STEP 13. Check the rear window defogger.....4443
The rear window defogger does not work. <vehicles with automatic air conditioning>....4443
DIAGNOSIS....4443
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line....4443
STEP 2. Using scan tool (M.U.T.-III), read the ETACS diagnostic trouble code.....4443
STEP 3. Using scan tool (M.U.T.-III), read the engine control module diagnostic trouble code....4443
STEP 4. Using scan tool (M.U.T.-III), check data list....4443
STEP 5. Check the rear window defogger relay.....4443
STEP 6. Voltage measurement at the rear window defogger connector.....4444
STEP 7. Resistance measurement at the rear window defogger connector.....4444
STEP 8. Voltage measurement at the rear window defogger relay connector.....4444
STEP 9. Check of short to power supply, and open circuit in power supply line between rear window defogger relay connector and fusible link.....4444
STEP 10. Voltage measurement at the rear window defogger relay connector.....4444
STEP 11. Check of short to power supply, and open circuit in input line between rear window defogger relay connector and ignition switch (IG2).....4444
STEP 12. Check of short to power supply, and open circuit in DEF1 line between rear window defogger relay connector and ETACS-ECU.....4444
STEP 13. Check the rear window defogger.....4445
INSPECTION....4445
REAR WINDOW DEFOGGER SWITCH CONTINUITY CHECK <VEHICLES WITH MANUAL AIR CONDITIONING>....4445
ON-VEHICLE SERVICE....4446
PRINTED HEATER CHECK....4446
REAR WINDOW DEFOGGER RELAY CHECK....4446
IMMOBILIZER SYSTEM <VEHICLES WITHOUT KOS>....4447
DIAGNOSIS....4449
HOW TO CONNECT THE SCAN TOOL (M.U.T.-III)....4449
HOW TO READ AND ERASE DIAGNOSTIC TROUBLE CODES....4450
HOW TO DIAGNOSE THE CAN BUS LINES....4451
CHECK OF FREEZE FRAME DATA....4451
DIAGNOSTIC TROUBLE CODE PROCEDURES....4452
DTC B1702: Transponder read error....4452
DIAGNOSIS....4453
STEP 1. Using scan tool (M.U.T.-III), read the ETACS diagnostic trouble code....4453
STEP 2. Check the ignition key inserted in the key hole for interference.....4453
STEP 3. Check with the spare key that has already been registered.....4453
STEP 4. Recheck for diagnostic trouble code.....4454
DTC B1703: Transponder ID unmatched....4454
DIAGNOSIS....4454
Register all the ignition key IDs again, and recheck the DTC.....4454
DTC B1722: Immobilizer-antenna fail....4455
DIAGNOSIS....4455
STEP 1. Check the key reminder switch (ignition key ring antenna)....4455
STEP 2. Check of short to power supply, short to ground, and open circuit in ANT+, ANT- line between ETACS-ECU connector and key reminder switch connector....4456
STEP 3. Recheck for diagnostic trouble code.....4456
STEP 4. Recheck for diagnostic trouble code.....4456
DTC B1731: PCM authentification timeout....4456
DIAGNOSIS....4457
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line....4457
STEP 2. Recheck for diagnostic trouble code.....4457
STEP 3. Recheck for diagnostic trouble code.....4458
DTC B1766: Already learned by other vehicle....4458
DIAGNOSIS....4458
STEP 1. All ignition keys registration....4458
STEP 2. Using scan tool (M.U.T.-III), diagnose the CAN bus line....4459
STEP 3. Check with another key that has already been registered.....4459
STEP 4. Recheck for diagnostic trouble code.....4459
DTC B1A28: PCM authentification error....4459
DIAGNOSIS....4460
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line....4460
STEP 2. Using scan tool (M.U.T.-III), read the engine control module diagnostic trouble code....4460
STEP 3. Using scan tool (M.U.T.-III), read the ETACS diagnostic trouble code....4460
STEP 4. Recheck for diagnostic trouble code.....4461
STEP 5. Recheck for diagnostic trouble code.....4461
SYMPTOM PROCEDURES....4461
Inspection Procedure 1: The ignition key cannot be registered with the scan tool (M.U.T.-III).....4461
DIAGNOSIS....4462
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line....4462
STEP 2. Check the ignition key inserted in the key hole for interference.....4462
STEP 3. Retest the system.....4462
STEP 4. Check which ignition key cannot be registered.....4463
STEP 5. Retest the system.....4463
STEP 6. Retest the system.....4463
Inspection Procedure 2: The engine does not start (cranking occurs but initial combustion does not).....4463
DIAGNOSIS....4464
STEP 1. Battery voltage check....4464
STEP 2. Using scan tool (M.U.T.-III), diagnose the CAN bus line....4464
STEP 3. Using scan tool (M.U.T.-III), read the engine control module diagnostic trouble code....4464
STEP 4. Using scan tool (M.U.T.-III), read the ETACS diagnostic trouble code.....4464
STEP 5. Check that the engine starts.....4464
STEP 6. Check that the engine starts.....4465
TERMINAL VOLTAGE CHECK TABLE....4465
ON-VEHICLE SERVICE....4465
GR00005100-54AA....4466
CHASSIS ELECTRICAL....4466
BATTERY....4469
ON-VEHICLE SERVICE....4469
FLUID LEVEL AND SPECIFIC GRAVITY CHECK....4469
CHARGE RATE....4470
STEP 1. Check the battery cables.....4470
STEP 2. Check the battery posts.....4470
STEP 3. Check the battery case and cover.....4470
STEP 4. Check the open circuit voltage.....4470
STEP 5. Battery charging....4471
STEP 6. Check the load test.....4471
IGNITION SWITCH....4473
DIAGNOSIS....4473
STANDARD FLOW OF DIAGNOSTIC TROUBLE SHOOTING....4473
SYMPTOM PROCEDURES....4474
Malfunction of the ignition switch power supply system....4474
DIAGNOSIS....4474
STEP 1. Check the battery power supply circuit to the ignition switch. Measure the voltage at ignition switch connector.....4474
STEP 2. Check the fuse.....4474
STEP 3. Check of open circuit in power supply line between ignition switch connector and junction block connector....4474
STEP 4. Check the ignition switch.....4474
STEP 5. Retest the system.....4474
ON-VEHICLE SERVICE....4474
IGNITION KEY REMINDER TONE ALARM INSPECTION....4474
REMOVAL SERVICE POINT....4476
INSPECTION....4477
IGNITION SWITCH CHECK....4477
KEY REMINDER SWITCH INSPECTION....4477
COMBINATION METER....4477
DIAGNOSIS....4480
STANDARD FLOW OF DIAGNOSTIC TROUBLESHOOTING....4480
HOW TO CONNECT THE SCAN TOOL (M.U.T.-III)....4480
HOW TO READ AND ERASE DIAGNOSTIC TROUBLE CODES....4481
HOW TO DIAGNOSE THE CAN BUS LINES....4482
CHECK OF FREEZE FRAME DATA....4483
DIAGNOSTIC TROUBLE CODE PROCEDURES....4484
DTC B1200: Odometer failure....4484
DTC B1201: Fuel information problem....4484
DIAGNOSIS....4484
STEP 1. Check of fuel pump and gauge assembly circuit....4485
STEP 2. Check the fuel level sensor.....4485
STEP 3. Resistance measurement at the fuel pump and gauge assembly connector....4485
STEP 4. Check of open circuit in ground line between fuel pump and gauge assembly connector and ground.....4485
STEP 5. Check of open circuit in F/G line between combination meter connector and fuel pump and gauge assembly connector.....4485
STEP 6. Using scan tool (M.U.T.-III), perform actuator test.....4486
STEP 7. Recheck for diagnostic trouble code.....4486
DTC B1209: B1209 Test mode....4486
DTC B2463: Rheostat switch sticking....4486
DTC U0100: Engine CAN timeout....4486
DIAGNOSIS....4487
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line....4487
STEP 2. Using scan tool (M.U.T.-III), read the engine control module diagnostic trouble code....4487
STEP 3. Using scan tool (M.U.T.-III), read the ETACS diagnostic trouble code.....4487
STEP 4. Recheck for diagnostic trouble code.....4487
STEP 5. Recheck for diagnostic trouble code.....4487
STEP 6. Recheck for diagnostic trouble code.....4487
DTC U0101: T/M CAN timeout....4487
DIAGNOSIS....4488
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line....4488
STEP 2. Using scan tool (M.U.T.-III), read the CVT diagnostic trouble code....4488
STEP 3. Using scan tool (M.U.T.-III), read the ETACS diagnostic trouble code.....4488
STEP 4. Recheck for diagnostic trouble code.....4488
STEP 5. Recheck for diagnostic trouble code.....4488
STEP 6. Check whether the DTC is reset.....4488
DTC U0121: ABS/ASC CAN timeout....4489
DIAGNOSIS....4489
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line....4489
STEP 2. Using scan tool (M.U.T.-III), read the ASC diagnostic trouble code....4489
STEP 3. Using scan tool (M.U.T.-III), read the ETACS diagnostic trouble code.....4489
STEP 4. Recheck for diagnostic trouble code.....4489
STEP 5. Recheck for diagnostic trouble code.....4489
STEP 6. Recheck for diagnostic trouble code.....4490
DTC U0131: EPS CAN timeout....4490
DIAGNOSIS....4490
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line....4490
STEP 2. Using scan tool (M.U.T.-III), read the EPS diagnostic trouble code.....4490
STEP 3. Using scan tool (M.U.T.-III), read the ETACS diagnostic trouble code.....4490
STEP 4. Recheck for diagnostic trouble code.....4491
STEP 5. Recheck for diagnostic trouble code.....4491
STEP 6. Recheck for diagnostic trouble code.....4491
DTC U0141: ETACS CAN timeout....4491
DIAGNOSIS....4491
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line....4491
STEP 2. Using scan tool (M.U.T.-III), read the ETACS diagnostic trouble code....4492
STEP 3. Using scan tool (M.U.T.-III), read the MFI diagnostic trouble code....4492
STEP 4. Recheck for diagnostic trouble code.....4492
STEP 5. Recheck for diagnostic trouble code.....4492
STEP 6. Recheck for diagnostic trouble code.....4492
DTC U0151: SRS-ABG CAN timeout....4492
DIAGNOSIS....4493
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line....4493
STEP 2. Using scan tool (M.U.T.-III), read the SRS diagnostic trouble code....4493
STEP 3. Recheck for diagnostic trouble code.....4493
STEP 4. Recheck for diagnostic trouble code.....4493
STEP 5. Recheck for diagnostic trouble code.....4493
DTC U0154: OCM CAN timeout....4493
DIAGNOSIS....4494
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line....4494
STEP 2. Using scan tool (M.U.T.-III), read the OCM diagnostic trouble code....4494
STEP 3. Using scan tool (M.U.T.-III), read the SRS diagnostic trouble code.....4494
STEP 4. Recheck for diagnostic trouble code.....4494
STEP 5. Recheck for diagnostic trouble code.....4494
STEP 6. Recheck for diagnostic trouble code.....4495
DTC U0168: WCM/F.A.S.T. CAN timeout....4495
DIAGNOSIS....4495
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line....4495
STEP 2. Using scan tool (M.U.T.-III), read the KOS diagnostic trouble code....4495
STEP 3. Using scan tool (M.U.T.-III), read the ETACS diagnostic trouble code....4495
STEP 4. Recheck for diagnostic trouble code.....4496
STEP 5. Recheck for diagnostic trouble code.....4496
STEP 6. Recheck for diagnostic trouble code.....4496
DTC U1000: OSS CAN timeout....4496
DIAGNOSIS....4496
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line....4496
STEP 2. Using scan tool (M.U.T.-III), read the KOS diagnostic trouble code....4497
STEP 3. Using scan tool (M.U.T.-III), read the ETACS diagnostic trouble code....4497
STEP 4. Recheck for diagnostic trouble code.....4497
STEP 5. Recheck for diagnostic trouble code.....4497
STEP 6. Recheck for diagnostic trouble code.....4497
DTC U1110: A/C CAN timeout/Not equipped....4497
DIAGNOSIS....4498
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line....4498
STEP 2. Using scan tool (M.U.T.-III), read the A/C diagnostic trouble code....4498
STEP 3. Using scan tool (M.U.T.-III), read the ETACS diagnostic trouble code....4498
STEP 4. Recheck for diagnostic trouble code.....4498
STEP 5. Recheck for diagnostic trouble code.....4498
STEP 6. Recheck for diagnostic trouble code.....4498
DTC U1190: No receive fault detect signal....4498
DIAGNOSIS....4499
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line....4499
STEP 2. Recheck for diagnostic trouble code.....4499
STEP 3. Recheck for diagnostic trouble code.....4499
DTC U1195: Coding not completed....4499
DIAGNOSIS....4499
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line....4499
STEP 2. Using scan tool (M.U.T.-III), read the ETACS diagnostic trouble code....4500
STEP 3. Recheck for diagnostic trouble code.....4500
SYMPTOM PROCEDURES....4501
Inspection Procedure 1: Power supply circuit check Inspection Procedure 2: The odometer and the trip meter are not displayed. In.....4501
DIAGNOSIS....4501
STEP 1. Using scan tool (M.U.T.-III), read the combination meter diagnostic trouble code....4501
STEP 2. Voltage measurement at the combination meter connector....4502
STEP 3. Check of open circuit in B+B line between the fusible link and combination meter connector.....4502
STEP 4. Voltage measurement at the combination meter connector....4502
STEP 5. Using scan tool (M.U.T.-III), check data list....4502
STEP 6. Check of open circuit in IG1 line between the ignition switch (IG1) and combination meter connector.....4503
STEP 7. Resistance measurement at the combination meter connector....4503
STEP 8. Check of open circuit in GND line between combination meter connector and ground.....4503
STEP 9. Retest the system....4503
Inspection Procedure 5: The speedometer does not work (The other meters work).....4503
DIAGNOSIS....4504
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....4504
STEP 2. Using scan tool (M.U.T.-III), read the MFI diagnostic trouble code.....4504
STEP 3. Using scan tool (M.U.T.-III), check data list....4504
STEP 4. Using scan tool (M.U.T.-III), check actuator test.....4504
STEP 5. Check by scan tool (M.U.T.-III) 'Special Function'....4505
STEP 6. Retest the system.....4505
Inspection Procedure 6: The tachometer does not work (the other meters work).....4505
DIAGNOSIS....4505
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line....4505
STEP 2. Using scan tool (M.U.T.-III), read the combination meter diagnostic trouble code....4505
STEP 3. Using scan tool (M.U.T.-III), read the MFI diagnostic trouble code.....4506
STEP 4. Using scan tool (M.U.T.-III), check actuator test....4506
STEP 5. Check by scan tool (M.U.T.-III) 'Special Function'....4506
STEP 6. Retest the system....4506
Inspection Procedure 7: Tone alarm does not sound normally.....4506
DIAGNOSIS....4507
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line....4507
STEP 2. Using scan tool (M.U.T.-III), read the combination meter diagnostic trouble code....4507
STEP 3. Using scan tool (M.U.T.-III), read for any diagnostic trouble code....4507
STEP 4. Check by scan tool (M.U.T.-III) 'Special Function'....4507
STEP 5. Retest the system....4507
Inspection Procedure 8: Fuel gauge does not work (the other meters work).....4507
DIAGNOSIS....4508
STEP 1. Using scan tool (M.U.T.-III), read the combination meter diagnostic trouble code.....4508
STEP 2. Check the fuel level sensor....4508
STEP 3. Using scan tool (M.U.T.-III), check data list....4508
STEP 4. Using scan tool (M.U.T.-III), check actuator test....4508
STEP 5. Retest the system.....4508
Inspection Procedure 9: The combination meter light does not illuminate normally or the multi-information display is not displayed normally.....4509
DIAGNOSIS....4509
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line....4509
STEP 2. Using scan tool (M.U.T.-III), read the combination meter diagnostic trouble code....4509
STEP 3. Using scan tool (M.U.T.-III), read for any diagnostic trouble code.....4509
STEP 4. Check by scan tool (M.U.T.-III) 'Special Function'....4509
STEP 5. Retest the system....4510
Inspection Procedure 10: The multi-information display screen cannot be changed with the operation of the multi-information display switch.....4510
DIAGNOSIS....4510
STEP 1. Using scan tool (M.U.T.-III), read the combination meter diagnostic trouble code.....4510
STEP 2. Check by scan tool (M.U.T.-III) 'Special Function'....4511
STEP 3. Retest the system.....4511
Inspection Procedure 11: Parking brake reminder tone alarm does not sound. Inspection Procedure 12: Brake warning light does not illuminate.....4511
DIAGNOSIS....4511
STEP 1. Check the speedometer.....4511
STEP 2. Check the parking brake switch.....4511
STEP 3. Check of short to power supply, and open circuit in BRK line between combination meter connector and parking brake switch connector.....4511
STEP 4. Check by scan tool (M.U.T.-III) 'Special Function'....4512
STEP 5. Retest the system.....4512
Inspection Procedure 13: Ambient temperature sensor does not work.....4512
DIAGNOSIS....4512
STEP 1. Check the ambient temperature sensor.....4512
STEP 2. Resistance measurement at the ambient temperature sensor connector....4512
STEP 3. Check of open circuit in SENG line between ambient temperature sensor connector and combination meter connector.....4513
STEP 4. Check of open circuit in AMB line between combination meter connector and ambient temperature sensor connector.....4513
STEP 5. Retest the system.....4513
Inspection Procedure 14: Seat belt reminder function does not work normally.....4513
DIAGNOSIS....4513
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line....4514
STEP 2. Using scan tool (M.U.T.-III), read the SRS diagnostic trouble code.....4514
STEP 3. Check the seat belt switch.....4514
STEP 4. Resistance measurement at the seat belt switch (driver’s side) connector....4514
STEP 5. Check of open circuit in ground line between seat belt switch (driver’s side) and ground.....4514
STEP 6. Check of short to power supply circuit in S/B- line between combination meter connector and seat belt switch (driver’s....4515
STEP 7. Check of short to power supply, and open circuit in BWLP line between combination meter connector and passenger’s air ....4515
STEP 8. Retest the system.....4515
ON-VEHICLE SERVICE....4518
SPEEDOMETER CHECK....4518
TACHOMETER CHECK....4519
HOW TO SET BY OPERATING THE SCAN TOOL (M.U.T.-III)....4520
HOW TO SET BY SPECIAL OPERATION OF SWITCH....4524
HOW TO INACTIVATE THE SERVICE REMINDER FUNCTION....4525
COMBINATION METER....4526
HEADLIGHT....4527
PRECAUTIONS ON HOW TO USE THE HEADLIGHT ASSEMBLY....4527
DIAGNOSIS....4530
DIAGNOSTIC FUNCTION....4530
HOW TO CONNECT THE SCAN TOOL (M.U.T.-III)....4530
HOW TO READ AND ERASE DIAGNOSTIC TROUBLE CODES....4531
HOW TO DIAGNOSE THE CAN BUS LINES....4532
DIAGNOSTIC TROUBLE CODE PROCEDURES....4533
DTC B1706: Flasher fuse blown....4533
DIAGNOSIS....4533
STEP 1. Check the flasher fuse.....4533
STEP 2. Check of open circuit in HAZ1 line between the ETACS-ECU connector and the fusible link.....4533
STEP 3. Using scan tool (M.U.T.-III), Check whether the diagnostic trouble code is stored again.....4534
DTC B1707: Flasher open....4534
DIAGNOSIS....4534
STEP 1. Confirm which turn-signal light is defective.....4534
STEP 2. Check the bulb(s) of the front turn-signal lights.....4535
STEP 3. Resistance measurement at the front turn-signal light (LH) connector or front turn-signal light (RH) connector.....4535
STEP 4. Check of open circuit in ground line between front turn-signal light (LH) connector or front turn-signal light (RH) connector and ground.....4535
STEP 5. Check of open circuit in TURN LH or TURN RH line between front turn-signal light (LH) connector or front turn-signal light (RH) connector and ETACS-ECU connector.....4535
STEP 6. Retest the system.....4536
STEP 7. Check the bulb(s) of side turn-signal lights.....4536
STEP 8. Resistance measurement at the side turn-signal light (LH) connector, side turn-signal light (RH) connector <Fender panel type>, door mirror assembly (LH) connector or door mirror assembly (RH) connector <Door mirror type>.....4536
STEP 9. Check of open circuit in ground line between side turn-signal light (LH) connector, side turn-signal light (RH) connecto.....4537
STEP 10. Check of open circuit in TURN LH or TURN RH line between side turn-signal light (LH) connector, side turn-signal light .....4537
STEP 11. Retest the system.....4537
STEP 12. Check the bulb(s) of rear turn-signal lights.....4537
STEP 13. Resistance measurement at the rear combination light (turn: LH) or rear combination light (turn: RH) connector.....4538
STEP 14. Check of open circuit in ground line between rear combination light (turn: LH) connector or rear combination light (turn: RH) connector and ground.....4538
STEP 15. Check of open circuit in TURN LH or TURN RH line between rear combination light (turn: LH) connector or rear combination light (turn: RH) connector and ETACS-ECU connector.....4538
STEP 16. Retest the system.....4538
STEP 17. Using scan tool (M.U.T.-III), Check whether the diagnostic trouble code is set again.....4539
SYMPTOM PROCEDURES....4540
Inspection Procedure A-1: None of the low-beam headlights illuminate.....4540
DIAGNOSIS....4540
STEP 1. Using scan tool (M.U.T.-III), read the diagnostic trouble code.....4540
STEP 2. Using scan tool (M.U.T.-III), check data list....4540
STEP 3. Check the headlight relay (LO).....4541
STEP 4. Voltage measurement at headlight relay (LO) connector.....4541
STEP 5. Check of short to power supply, and open circuit in power supply lines between headlight relay (LO) connector and fusible link.....4541
STEP 6. Check of open circuit in H/LP LO line between headlight relay (LO) connector and ETACS-ECU connector.....4541
STEP 7. Retest the system.....4541
Inspection Procedure A-2: None of the high-beam headlights illuminate.....4541
DIAGNOSIS....4542
STEP 1. Using scan tool (M.U.T.-III), read the diagnostic trouble code.....4542
STEP 2. Using scan tool (M.U.T.-III), check data list....4542
STEP 3. Check the headlight relay (HI).....4542
STEP 4. Voltage measurement at headlight relay (HI) connector.....4543
STEP 5. Check of short to power supply, and open circuit in power supply lines between headlight relay (HI) connector and fusible link.....4543
STEP 6. Check of open circuit in H/LP HI line between headlight relay (HI) connector and ETACS-ECU connector.....4543
STEP 7. Retest the system.....4543
Inspection Procedure A-3: The high-beam and low-beam headlights do not illuminate when the passing switch is operated.....4543
DIAGNOSIS....4544
STEP 1. Using scan tool (M.U.T.-III), read the ETACS-ECU diagnostic trouble code.....4544
STEP 2. Check that the headlights operate.....4544
STEP 3. Retest the system.....4544
Inspection Procedure A-4: One of the headlights does not illuminate.....4544
DIAGNOSIS....4544
STEP 1. Bulb check....4544
STEP 2. Resistance measurement at the headlight (LH) connector, headlight (RH) connector....4545
STEP 3. Check of open circuit in ground line between headlight (LH) connector or headlight (RH) connector and ground.....4545
STEP 4. Check of short to power supply, and open circuit in power supply line between headlight (LH) connector or headlight (RH) connector and headlight relay (LO) connector.....4545
STEP 5. Retest the system....4545
Inspection Procedure A-5: The high-beam indicator light does not illuminate.....4545
DIAGNOSIS....4546
STEP 1. Check the headlight.....4546
STEP 2. Using scan tool (M.U.T.-III), diagnose the CAN bus line....4546
STEP 3. Using scan tool (M.U.T.-III), read the ETACS diagnostic trouble code.....4546
STEP 4. Check by scan tool (M.U.T.-III) 'Special Function'....4546
Inspection Procedure A-6: The headlight automatic-shutdown function does not work normally.....4546
DIAGNOSIS....4547
STEP 1. Using scan tool (M.U.T.-III), Check the configuration function....4547
STEP 2. Using scan tool (M.U.T.-III), read the diagnostic trouble code.....4547
STEP 3. Using scan tool (M.U.T.-III), check data list....4547
STEP 4. Retest the system.....4547
Inspection Procedure A-7: The position light does not illuminate.....4547
DIAGNOSIS....4548
STEP 1. Using scan tool (M.U.T.-III), read the diagnostic trouble code.....4548
STEP 2. Using scan tool (M.U.T.-III), check data list....4548
STEP 3. Retest the system.....4548
Inspection Procedure A-8: Either of the position lights does not illuminate.....4548
DIAGNOSIS....4549
STEP 1. Bulb check....4549
STEP 2. Resistance measurement at position light (LH) connector, position light (RH) connector....4549
STEP 3. Check of open circuit in ground line between position light (LH) connector or position light (RH) connector and ground.....4549
STEP 4. Check of short to power supply, and open circuit in power supply line between position light (LH) connector or position light (RH) connector and junction block connector.....4549
STEP 5. Retest the system.....4550
Inspection Procedure A-9: When the ignition switch is turned to the ON position with the lighting switch at the OFF or TAIL position, the headlights will illuminate briefly.....4550
DIAGNOSIS....4550
STEP 1. Check dome light fuse.....4550
STEP 2. Check that the headlights operate.....4550
STEP 3. Using scan tool (M.U.T.-III), read the ETACS diagnostic trouble code....4551
STEP 4. Voltage measurement at column switch connector.....4551
STEP 5. Check of short to power supply, and open circuit in power supply line between column switch connector and junction block connector.....4551
STEP 6. Retest the system.....4551
Inspection Procedure A-10: Daytime running light function does not work normally.....4552
DIAGNOSIS....4552
STEP 1. Verify the headlight (low-beam) operation.....4552
STEP 2. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....4552
STEP 3. Using scan tool (M.U.T.-III), read the ETACS-ECU diagnostic trouble code.....4552
STEP 4. Using scan tool (M.U.T.-III), read the MFI system diagnostic trouble code.....4553
STEP 5. Check the parking brake switch.....4553
STEP 6. Temporarily replace the headlight relay (LO), and retest the system.....4553
Inspection Procedure B-1: None of the turn-signal lights illuminate.....4553
DIAGNOSIS....4554
STEP 1. Using scan tool (M.U.T.-III), read the diagnostic trouble code....4554
STEP 2. Using scan tool (M.U.T.-III), check data list....4554
STEP 3. Retest the system....4554
Inspection Procedure B-2: The comfort flasher does not work normally.....4554
DIAGNOSIS....4554
STEP 1. Using scan tool (M.U.T.-III), Check the configuration function.....4554
STEP 2. Using scan tool (M.U.T.-III), read the ETACS-ECU diagnostic trouble code.....4555
STEP 3. Check that the turn-signal light operate.....4555
STEP 4. Replace the ECU.....4555
Inspection Procedure B-3: The turn-signal indicator lights do not illuminate.....4555
DIAGNOSIS....4555
STEP 1. Check turn-signal light....4555
STEP 2. Using scan tool (M.U.T.-III), diagnose the CAN bus line....4555
STEP 3. Using scan tool (M.U.T.-III), read the diagnostic trouble code.....4555
STEP 4. Check by scan tool (M.U.T.-III) 'Special Function'....4556
Inspection Procedure B-4: One of the turn-signal lights does not illuminate.....4556
DIAGNOSIS....4556
STEP 1. Confirm which turn-signal light is defective.....4556
STEP 2. Resistance measurement at the side turn-signal light connector.....4557
STEP 3. Check of open circuit in ground line between side turn-signal light connector <Fender mirror type>, door mirror assembly <Door mirror type> and ground.....4557
STEP 4. Check of open circuit in TURN LH or TURN RH line between side turn-signal light connector <Fender mirror type>, door mirror assembly connector <Door mirror type> and ETACS-ECU connector.....4557
STEP 5. Retest the system.....4558
ON-VEHICLE SERVICE....4558
HEADLIGHT AIMING....4558
PRE-AIMING INSTRUCTIONS (LOW-BEAM)....4558
HEADLIGHT ADJUSTMENT (LOW-BEAM)....4559
LUMINOUS INTENSITY MEASUREMENT....4560
BULB REPLACEMENT....4560
HEADLIGHT BULB REPLACEMENT....4560
POSITION LIGHT BULB REPLACEMENT....4561
FRONT TURN-SIGNAL LIGHT BULB REPLACEMENT....4561
FRONT SIDE-MARKER LIGHT BULB REPLACEMENT....4561
HEADLIGHT AUTOMATIC-SHUTDOWN FUNCTION CHECK....4562
HEADLIGHT....4563
INSPECTION....4564
HEADLIGHT RELAY CHECK....4564
REAR COMBINATION LIGHT....4565
DIAGNOSIS....4567
SYMPTOM PROCEDURES....4567
Inspection Procedure 1: None of the taillights illuminate.....4567
DIAGNOSIS....4568
STEP 1. Using scan tool (M.U.T.-III), read the diagnostic trouble code....4568
STEP 2. Using scan tool (M.U.T.-III), check data list....4568
STEP 3. Retest the system....4568
Inspection Procedure 2: One of taillights does not illuminate.....4568
DIAGNOSIS....4568
STEP 1. Check the bulbs of the taillights.....4568
STEP 2. Resistance measurement at the rear combination light (taillight: LH) connector or rear combination light (taillight: RH) connector.....4569
STEP 3. Check of open circuit in ground line between the rear combination light (taillight: LH) connector or rear combination light (taillight: RH) connector (ground terminal) and ground.....4569
STEP 4. Check of open circuit in TAIL LP lines between the rear combination light (taillight: LH) connector or rear combination light (taillight: RH) connector and ETACS-ECU connector.....4569
STEP 5. Retest the system.....4569
Inspection Procedure 3: The back-up light do not illuminate normally.....4569
DIAGNOSIS....4570
STEP 1. Check the operation of the position lights and the headlights.....4570
STEP 2. Check the transmission range switch <CVT> or back-up light switch <M/T>.....4570
STEP 3. Voltage measurement at the transmission range switch connector <CVT> or back-up light switch connector <M/T>.....4570
STEP 4. Check of open circuit in power supply line between the transmission range switch connector <CVT> or back-up light switch connector <M/T> and the ignition switch (IG1).....4571
STEP 5. Check the bulb of the back-up light....4571
STEP 6. Resistance measurement at the rear combination light (back-up light) connector....4571
STEP 7. Check of open circuit in ground line between rear combination light (back-up light) connector and ground.....4571
STEP 8. Check of open circuit in output line between the rear combination light (back-up light) connector and back-up light switch connector.....4571
STEP 9. Retest the system....4571
Inspection Procedure 4: The stoplight do not illuminate or go out normally.....4572
DIAGNOSIS....4572
STEP 1. Using scan tool (M.U.T.-III), check data list....4572
STEP 2. Voltage measurement at the joint connector....4572
STEP 3. Check of short to power supply, and open circuit in power supply line between the joint connector and the fusible link.....4572
STEP 4. Resistance measurement at the liftgate spoiler connector <high-mounted stoplight>, rear combination light (stop: LH) connector, rear combination light (stop: RH) connector....4572
STEP 5. Check the following wiring harness....4573
STEP 6. Check the following wiring harness....4573
STEP 7. Retest the system....4573
ON-VEHICLE SERVICE....4573
REPLACE THE BULB....4573
REAR TURN-SIGNAL LIGHT BULB REPLACEMENT....4573
STOPLIGHT/TAILLIGHT/REAR SIDE-MARKER LIGHT BULB REPLACEMENT....4573
BACK-UP LIGHT BULB REPLACEMENT....4574
FRONT FOG LIGHT....4575
DIAGNOSIS....4578
SYMPTOM PROCEDURES....4578
Inspection Procedure 1: The front fog lights do not illuminate normally.....4578
DIAGNOSIS....4579
STEP 1. ETACS-ECU coding data check....4579
STEP 2. Check the operation of the headlights.....4579
STEP 3. Using scan tool (M.U.T.-III), read the other system diagnostic trouble code....4579
STEP 4. Using scan tool (M.U.T.-III), check data list.....4579
STEP 5. Check the front fog light relay....4579
STEP 6. Voltage measurement at the front fog light relay connector....4579
STEP 7. Check of short to power supply, and open circuit in power supply lines between front fog light relay connector and the fusible link.....4580
STEP 8. Check of short to power supply, and open circuit in FOGY line between front fog light relay connector and the ETACS-ECU connector.....4580
STEP 9. Check of short to power supply, and open circuit in output lines between front fog light relay connector and the front fog light (LH) or front fog light (RH) connector.....4580
STEP 10. Check of open circuit in ground lines between the front fog light (LH) or front fog light (RH) connector and ground.....4580
STEP 11. Retest the system....4580
Inspection Procedure 2: One of the front fog lights does not illuminate normally.....4580
DIAGNOSIS....4580
STEP 1. Bulb check....4580
STEP 2. Resistance measurement at the front fog light (LH) connector or front fog light (RH) connector....4580
STEP 3. Check of open circuit in ground lines between the front fog light (LH) connector or front fog light (RH) connector and ground.....4580
STEP 4. Check of short to power supply, and open circuit in output lines between front fog light relay connector and the front fog light (LH) or front fog light (RH) connector.....4581
STEP 5. Retest the system....4581
Inspection Procedure 3: The front fog light indicator does not illuminate normally.....4581
DIAGNOSIS....4581
STEP 1. Check the front fog lights....4581
STEP 2. Using scan tool (M.U.T.-III), diagnose the CAN bus line.....4581
STEP 3. Using scan tool (M.U.T.-III), read the ETACS diagnostic trouble code.....4581
STEP 4. Check by scan tool (M.U.T.-III) 'Special Function'....4581
ON-VEHICLE SERVICE....4582
FRONT FOG LIGHT AIMING....4582
PRE-AIMING INSTRUCTIONS....4582
FRONT FOG LIGHT ADJUSTMENT....4583
REPLACE THE BULB....4583
INSPECTION....4585
FRONT FOG LIGHT RELAY CHECK....4585
SIDE TURN-SIGNAL LIGHT....4586
<DOOR MIRROR TYPE>....4586
REMOVAL SERVICE POINT....4586
INSTALLATION SERVICE POINT....4587
DOME LIGHT....4588
DIAGNOSIS....4590
SYMPTOM PROCEDURES....4590
Inspection Procedure 1: The dome light does not illuminate normally.....4590
DIAGNOSIS....4591
STEP 1. Retest the system.....4591
STEP 2. Dome light bulb check....4591
STEP 3. Check of open circuit in power supply lines between the dome light connector and the fusible link.....4591
STEP 4. Check of open circuit in ground line between the dome light connector and the ground.....4591
STEP 5. Retest the system....4591
STEP 6. Using scan tool (M.U.T.-III), check data list.....4592
STEP 7. Check of open circuit in ROOM LP lines between the dome light connector and the ETACS-ECU connector.....4592
STEP 8. Retest the system....4592
Inspection Procedure 2: The luggage compartment light does not illuminate normally.....4592
DIAGNOSIS....4593
STEP 1. Dome light operation check....4593
STEP 2. Luggage compartment light bulb check....4593
STEP 3. Check of open circuit in power supply lines between the luggage compartment light connector and the fusible link.....4593
...
STEP 6. Check the symptom.....5791
Inspection Procedure 8: When the Cruise Control ON/OFF Switch is Turned ON, the Cruise Control Indicator Lamp does not Illuminate (However, the Cruise Control System is Normal).....5791
DIAGNOSIS....5791
STEP 1. Check the CAN bus system diagnosis.....5791
STEP 2. Check the MFI system diagnostic trouble code.....5792
STEP 3. Check the combination meter system special function.....5792
STEP 4. Check the symptom.....5792
STEP 5. Check the symptom.....5792
Inspection Procedure 9: When The Cruise Control Switch is Operated, The System is not Turned ON.....5792
DIAGNOSIS....5793
STEP 1. Check the MFI system diagnostic trouble code.....5793
STEP 2. Check the data list.....5793
STEP 3. Check the cruise control switches.....5793
STEP 4. Check the symptom.....5793
CHECK AT THE ENGINE CONTROL MODULE TERMINAL....5795
ON-VEHICLE SERVICE....5796
CRUISE CONTROL SWITCH CHECK....5796
CRUISE CONTROL ON/OFF SWITCH CHECK....5796
CRUISE CONTROL SETTING....5796
SPEED-INCREASE SETTING....5796
SPEED-REDUCTION SETTING....5797
RETURN TO THE SET SPEED BEFORE CANCELLATION AND CRUISE CONTROL CANCELLATION....5797
CRUISE CONTROL SYSTEM COMPONENT CHECK....5798
CRUISE CONTROL SWITCH CHECK....5798
STOP LIGHT SWITCH CHECK....5798
CLUTCH INTERLOCK SWITCH CHECK <M/T>....5798
TRANSMISSION RANGE SWITCH ('N' POSITION) CHECK <CVT>....5798
THROTTLE VALVE CONTROL SERVO CHECK....5798
CRUISE CONTROL SWITCH....5799
EMISSION CONTROL....5800
VACUUM HOSES....5801
VACUUM HOSE INSTALLATION....5802
VACUUM HOSE CHECK....5802
POSITIVE CRANKCASE VENTILATION SYSTEM....5803
CRANKCASE VENTILATION SYSTEM CHECK....5803
POSITIVE CRANKCASE VENTILATION (PCV) VALVE CHECK....5804
EVAPORATIVE EMISSION CONTROL SYSTEM....5804
PURGE CONTROL SYSTEM CHECK (PURGE FLOW CHECK)....5806
EVAPORATIVE EMISSION PURGE SOLENOID CHECK....5807
INSTALLATION SERVICE POINTS....5808
INSPECTION....5809
EVAPORATIVE EMISSION VENTILATION SOLENOID CHECK....5809
CATALYTIC CONVERTER....5810
INDEX....5812
PrefaceForMMNA_Vol1....5836
PrefaceForMMNA_Vol2....5840
EL_15_intro....5844
Mitsubishi Mirage, Galant, Diamant Repair Service Manual 1990-2000
